American Standard Bath/Shower Trim Kits T373.500 User manual

ENFIELD
FINISHED WALL
4"
BOTTOM OF TUB
74" FOR HEAD
CLEARANCE
5-1/8" REF.
7-7/8" REF.
18" OPTIONAL
5-3/4" REF.
1/2" NPT
1/2" NPT
9-1/8"
1-1/2” REF.
OPTIONAL TO FINISHED
FLOOR USUALLY
BETWEEN 65'' AND 80''
1-1/2” REF.
TOP OF TUB RIM
M968285 Rev. 1.1
T373.502 T373.522
T373.501 T373.521
T373.500 T373.520
Installation
Instructions
Certified to comply with ANSI A112.18.1
BATH/SHOWER
TRIM KITS
with EverClean™ Finish
Congratulations on purchasing your American Standard faucet with
EverClean finish found only on American Standard faucets.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Required Tools
Adjustable Wrench Channel Locks
Flat Blade Screwdriver
Plumbers' Putty or Caulking
Phillips Screwdriver
ROUGHING-IN DIMENSIONS
Installation for Bath/Shower, Shower only, or
Valve only Trim.
ODimensions are for reference.
EverClean Finish
• One wipe effortlessly removes spots
• Eliminates the need for cleaners and scrubbing
• Permanent surface protectant remains beautiful
for the life of the faucet
• EverClean™ available on: Polished Chrome, Satin Nickel,
Stainless Steel, Polished Brass (or any combination of these finishes)

VALVE LEAKS WHEN SHUT OFF
Remove CARTRIDGE (1) by removing CARTRIDGE SCREWS (2).
Remove three SCREWS (3) from FIXATION RING (4)
and pull out PRESSURE BALANCING (5) unit.
Clean SEALS (9) on base of CARTRIDGE (1). Check base of PRESSURE
BALANCING UNIT (5) and clean O-RINGS (6). Remove CAPS (7) and check
O-RINGS on inside of CAPS (7) for debris. Clean inside sealing surfaces of VALVE BODY (8).
Re-assemble PRESSURE BALANCING UNIT (5) and CARTRIDGE (1). Tighten all screws.
Turn on water supply and see above for installing TRIM and HANDLE.
If it still leaks, replace pressure balancing unit (M952100-0070A).
UNABLE TO MAINTAIN CONSTANT TEMPERATURE
Remove PRESSURE BALANCE UNIT (5).
 Remove CAPS (7) and clean valve thoroughly.
  Examine balancing unit and check condition of O-ring on end of piston. Piston should move back and forth.
Order Repair Part M952100-0070A if balancing unit is defective. Replace CAPS (7) and install PRESSURE
BALANCE UNIT (5). Make sure inlets line up with two holes in bottom of casting.
Top flange should butt-up against top of casting.
INSTALL TRIM
CAUTION: Protect finish on SHOWER ARM, SHOWER HEAD
and TUB SPOUT when installing.
When finished tiling the wall, remove PLASTER GUARD (A)
and turn off water supply.
Install STEM ADAPTER (1) onto valve stem with ADAPTER
SCREW (2).
Push CAP (3) over VALVE CARTRIDGE (4).
Mount ESCUTCHEON (5) to valve body with SCREWS (6).
Push DIAL PLATE (7) over CAP (3) and into the four alignment
holes in ESCUTCHEON (5).
Remove PIPE CAP (8) and PIPE CAP (9) from shower pipe and tub filler
pipe.
 Install SHOWER ARM (10), SHOWER HEAD (11) and TUB
FILLER SPOUT (12) by threading onto pipe nipples using teflon
tape or pipe sealant.
Align HANDLE (13, 14) and push onto STEM ADAPTER (1).
Tighten set screw in HANDLE (13, 14) securley with HEX
WRENCH (15) supplied.
1
2TO GAIN ACCESS TO VALVE FOR SERVICING
Remove HANDLE and TRIM. See step one and reverse assembly
procedure. HANDLE
and TRIM
10
11
5
11
8
4
9
12
9
4
13
14
10
(4) ALIGNMENT
HOLES FOR
DIAL PLATE 1
2
3
A
M968285 Rev. 1.1

ADJUST HOT LIMIT STOP
By restricting HANDLE rotation and limiting the
amount of hot water allowed to mix with the
cold, the HOT LIMIT SAFETY STOP (1) reduces
risk of accidental scalding. To set the maximum
hot water temperature of your faucet, you
need to adjust the setting on the HOT LIMIT
SAFETY STOP (1).
  Turn CARTRIDGE STEM (2) to the OFF position
(coldest setting) before making adjustment to
HOT LIMIT STOP (1). Use a flat blade
screwdriver to pry free the HOT LIMIT SAFETY
STOP (1).
Pull forward and rotate counterclockwise
one number to limit hot water temperature.
Use ARROW (3) on CARTRIDGE (4) and
NUMBERS (5) on HOT LIMIT STOP (1) for
indication.
TEST INSTALLED FITTING
Turn VALVE (1) "off".
 With HANDLE (1) in "off" position, turn on water supplies and check all connections
for leaks.
  Operate HANDLE (1) and flush water lines thoroughly. Pull DIVERTER (2) up and check
SHOWER (3) for proper operation.
  Check SPOUT (4) and SHOWER (3) connections for leaks.
4
3
5
4
3
1
2
BACK TO BACK INSTALLATION
Remove PRESSURE BALANCE UNIT (5). Rotate PRESSURE BALANCE UNIT (5) 180˚ so that the inlets face up and the
large outlet port faces down.
Push PRESSURE BALANCE UNIT (5) in casting make sure inlets line up with holes in bottom of casting. Top flange should
butt up against top of casting. Reassemble FIXATION RING (4) and CARTRIDGE (1).
BACK TO BACK INSTALLATION
ROTATE 180˚
12
9
5
5
7
8
6
43
INLETS
LARGE OUTLET
M968285 Rev. 1.1
6EverClean™ Finish Care Instructions
American Standard’s EverClean finish will wipe clean with a soft, dry cloth. A soft cloth with
clean water may also be used, if desired. No additional cleaning products are required.
DO NOT USE: Soaps, acid, polish, abrasives, harsh cleaners, or a cloth with a coarse surface.
1
5
1
3
1
1
9
7
5
3
1
0
1
5
4
3
2
1
5
1
3
1
1
9
7
5
3
1
1
5
1
3
1
1
9
7
5
3
1
COLDER
(Larger Numbers)
0 1 3 5 7 9 11 13 15
HOTTER
(Smaller Numbers)
0 1 3 5 7 9 11 13 15
1
5
4
3
2