American Standard Deck-Mount Bath Filler 2980 User manual

*Wrench
M968212
Certified to comply with ANSI A112.18.1M
Required Tools
*Supplied with Fitting
* ex key
RECESS
Turn off hot and cold water supplies before beginning.
CAUTION
12
Insert SPOUT S ANK (1) through center hole of MOUNTING LEDGE.
Make sure that the RUBBER RING (2) is properly seated in RECESS
at base of SPOUT (3).
Assemble RUBBER WAS ER (4) and BRASS WAS ER (5) onto
S ANK (1). From underside of ledge secure SPOUT (3) into position
with LOCKNUT (6).
SPOUT ASS MBLY PR PAR TUB AND T ASS MBLY
3
4
2
3
1
34
1
2
4
6
5
Prepare TUBE and TEE ASSEMBLY (1) to fit center to center
VALVE (2) location (between 6-1/2" and 12"). If necessary,
cut and/or bend TUBING carefully. Make sure tube bend is
close to the TEE (1) so that it will not effect the compression
joint at the VALVE CONNECTION.
Remove COUPLING NUT (3) and FERRULE (4) from each
VALVE (2) and slide onto TUBING (5).
ADJ. 6-1/2 TO 12
5
Flat Blade Screwdriver
Adjustable Wrench
Channel Locks
MOUNTING
LEDGE.
VALV inlet is 3/4-inch NPT male.
NOT
MOUNTING
SURFACE
ADJ. 6-1/2 TO 12
2-1/2D.
2-1/2D.
3-1/2"
ROUGHING-IN DIM NSIONS
MOUNTING
SURFACE
2-1/2D. 2-1/2D.
2-7/8"
8-5/8"
4-1/4"
D CK-MOUNT
BATH FILL R
Installation
Instructions
2980
2981
Thank you for selecting American-Standard...the
benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
by
COLLECTION
™
“”
THE
1-1/2 MAX.
1-1/4
MAX.
1-3/16 D.
3
( ) (C)
1-1/8 D.
7-1/4
12 MAX
2-1/16
D.
1-1/16 D.
3/4-14 MALE
N.P.T. INLETS

M968212
9
2
4
5/16'' MIN. MOUNTING
SURFACE
10
11
11
10
1
3
Push TUBING (3) ends into VALVE (4) side outlets. Insert VALVES (4)
into mounting holes from underside of ledge.
Press TEE (5) onto SPOUT S ANK (6) making certain that the O-RING (7) is
properly seated on S ANK (6). Push COUPLING (8) into TEE (5) and attach to
SPOUT S ANK (6) and tighten.
Install LOCKNUTS (1) and RUBBER WAS ERS (2) onto valve shanks.
Place RUBBER RING (10) into ESCUTC EON ADAPTERS (9) and thread onto
valves until snug against internal stop.
Tighten LOCKNUT (1) to secure VALVE (4) position.
Slide FERRULE (12) and COUPLING NUT (13) to outlet of VALVE (4) and tighten
COUPLING NUT (13) firmly.
Connect OT water supply to inlet of left VALVE and COLD water supply to inlet of
right VALVE using appropriate connector.
VALV ASS MBLY
HOT
COLD
12
4
13
7
6
8
5
13
12
34
MOUNTING
SURFACE
Thread of VALVE BODY (4) should extend at least 5/16 inch above MOUNTING
SURFACE (11). If necessary, adjust LOCKNUT (1).
10
9
9
4
Push INDEX CAP (6) in hole of ANDLE (4).
Secure ANDLE (4) with ANDLE SCREW (5).
Find correct position of ANDLE (4) by adjusting male teeth on
ADAPTER (1) to female teeth in ANDLE (4).
Thread ANDLE BASE (3) onto DECK ADAPTER (7)
Push ANDLE (4) onto ADAPTER (1).
Push ADAPTER (1) on VALVE STEM (2), so that the hole of the
ADAPTER (1) without spline is facing up. See figure "A".
1
2
TOP
Figure "A"
SPLINE END DOWN
INSTALL HANDL S
4
3
7
5
6
5S RVIC
To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position.
Pull out INDEX CAP (1) and remove
ANDLE SCREW (2).
Pull off ANDLE (3), and unscrew
ESCUTC EON (4).
Pull off STEM ADAPTER (7).
Remove SPRING CLIP (6).
Lift STOP WAS ER (5), turn 90° and replace.
Replace SPRING CLIP (6) and STEM ADAPTER (7).
Reinstall ESCUTC EON (4) and ANDLE
ASSEMBLY (1,2 & 3).
If spout drips, operate handles several times
from OFF to ON position. Do not force - handles
turn only 90°.
90°5
6
2
4
3
7
1

M968212
9
CAR INSTRUCTIONS:
DO: SIMPLY RINS TH PRODUCT CL AN WITH CL AR
WAT R. DRY WITH A SOFT COTTON FLANN L CLOTH.
DO NOT: CL AN TH PRODUCTWITH SOAPS, ACID,
POLISH, ABRASIV S, HARSH CL AN RS, OR A CLOTH
WITH A COARS SURFAC .
OT LINE FOR ELP
For toll-free information and answers to your questions, call:
1 [phone]
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2002
ex wench, supplied
HANDSHOW R INSTALLATION (Model 2981 series only)
T ST INSTALL D FAUC T
7
Turn VALVES "off" and attach handles.
Lift ANDS OWER from OLDER, direct spray into tub, lift
TRANSFER KNOB to check ANDS OWER and OSES for leaks.
Turn handles "off."
Check with local codes, and if required, add a vacuum breaker
kit (part no. 028708) at specified height. Refer to the install-
lation instructions supplied with the kit.
IMPORTANT
Drop SPRAY ESCUTC EON (1) through the fourth hole of the tub ledge (12" max from SPOUT
center) with SPRAY ESCUTC EON (1) directed towards tub center. Be sure RUBBER RING (2)
is properly seated in ESCUTC EON (1). Install RUBBER WAS ER (3) and LOCKNUT (4} from
underside of ledge.
Secure SPRAY ESCUTC EON (1) by tightening LOCKNUT (4).
Add SEAL WAS ER (5) and connect OSE (10) to outlet nipple
at the bottom of TEE (7). Tighten firmly.
Slip S OWER OSE (8) with COUPLING NUT through SPRAY
OLDER (6) and ESCUTC EON (1). Install SEAL (9) and
connect both OSES (8) and (10). INSTALL second SEAL (9)
and connect AND S OWER (11) to SPRAY OSE (8).
When not in use, HANDSHOW R should be seated
in the HOLD R.
NOT
Before the bathroom is completely finished, you may
want to remove spout, handshower, and handles.
To remove handles, reverse steps in section 4.
To remove SPOUT (1), proceed as follows:
Lift TRANSFER ROD (2) and unscrew KNOB (3). (Model 2555.901only).
Remove PLUG BUTTON (4) and remove SET SCREW (5) using hex
wrench supplied.
Lift SPOUT (1) off S ANK (6) carefully and remove RUBBER
RING (7).
Unscrew S ANK SLEEVE (8) and lift TRANSFER ROD (2) from
S ANK (6). (Model 2555.901only).
Reverse sequence to re-install SPOUT (1). Be sure RUBBER
RING (7) is properly seated in its recess at the base of the SPOUT (1).
Make certain SET SCREW (5) is properly aligned and tight so that
SPOUT (1) is locked in place.
8
6
With handles in "off" position, turn on water supplies and check
all connections for leaks.
Operate both handles and flush water lines thoroughly.
Check SPOUT mounting for leaks.
The flow rate of this Tub Filler exceeds 20 gallons/minute
at higher water pressure. Do not fill bathtub unattended.
CAUTION
1
2
3
4
5
5
7
8
10
9
9
11
1
2
3
4
6
7
6
8