American Standard Chandler 7048 Series User manual

CHANDLER™ APRON KITCHEN SINK
MODEL 7048 SERIES
Installation
Instructions
790759-100 REV A
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
BEFORE YOU BEGIN...Unpack new sink and inspect carefully for damage. Replace the sink in its original
packing carton to protect it until you are ready to begin installation.
Certified to comply with ANSI Z124.6
Patent Pending
Observe local plumbing and building codes.
™
RECOMMENDED TOOLS & MATERIALS
Putty Knife
Pipe Wrench
Channel Locks
Drill
Phillips Screwdriver
Regular Screwdriver
Adjustable Wrench
Basin Wrench
Saber Saw
Plumbers' Putty or
Caulking
Various Carpentry Tools
Tubing Cutter
Tape Measure
Hacksaw
Silicone Adhesive
M A D E W I T H
Product names listed herein are trademarks of American Standard Inc. unless otherwise noted.
Corian®Dupont registered trademark © American Standard Inc. 2004
PRODUCT REQUIREMENTS
Due to the special nature of this installation, American Standard recommends that an experienced cabinet
maker build the new cabinet or modify an existing cabinet to achieve a satisfactory installation.
To ensure proper fit of the sink in the cabinet, we suggest you provide the cabinet maker with the actual sink
that will be installed.
NOTES
The cabinet designs illustrated below are intended as suggestions only. Your specific installation requirements
may vary from those shown.
SINK DIMENSIONS
NOTE: Tile recess is
designed to accept four
6" x 6" x 5/16" thick tiles
(by others). Secure tiles
with silicone adhesive.
3/8
(10mm)
2
(51mm)
6-3/16
(157mm) 9-3/4
(248mm)
SEALING
COMPOUND
FRONT OF
CABINET
24-1/2
(622mm)
TILE RECESS
33 (838mm)
7-1/8
(181mm)
3-1/2
(89mm) DIA.
1-3/8 (35mm) DIA.
HOLES TYP.
8-3/4
(222mm)
22
(558mm)
C/L
7048.804
4 HOLE
VARIATION
1-3/4
(44mm) DIA.
1-1/2
(38mm) REF.
36
(914mm)
4-1/2
(114mm) 9-1/2
(241mm)
1 (25mm)
RAD. TYP.
CABINET DESIGN
The sink is designed to be installed with the apron exposed and the back of the apron flush against the front of
the cabinet.

790759-100 REV A 2
COUNTERTOP
TRACED LINE
OF SINK
3/8 IN.
MAX. 25mm (1")
COUNTERTOP
OVERHANG-DIM "X"
CABINET FACE
SINK CUTOUT
LINE
1a
1
ALIGN MARKS CENTER OF MOUNTING
LOCATION MARKED ON
COUNTERTOP
CENTER MARK ON
BACKSIDE OF SINK
SIDE
VIEW
COUNTERTOP
CABINET
FACE
SHOULD BE
MAXIMUM
25mm (1")
Mark
X
XCOUNTERTOP
22
(559mm)
APRON
EDGE
APRON
PORTION
OF SINK
CABINET
FACE
X
TOP
VIEW
C/L
SINK INSTALLATION
SINK UPSIDE DOWN
SINK CUTOUT
A. Mark center of backside of sink. Mark center of location on counter top approx. 22in. from outside
edge of countertop.
B. Mark countertop to show the cabinet face location (dim. X) .
C. Place sink, upside down, on countertop. Align centerline marks of sink and countertop.
D. Align the apron edges with the cabinet face marks on countertop.
E. Trace outside of sink (this is not the cut line.). Carefully remove sink, set aside.
A. Measure 3/8 in. inside of marked line - this is the sink cutout line.
B. Cut out countertop.
BCA
A
C
SINK PLACED
UPSIDE DOWN
ON COUNTERTOP
B
TRACE
THIS EDGE
E
D
B
SINK CUTOUT
LINE
DIM "X" B
A

790759-100 REV A 3
1b
1C
TRACED LINE
OF SINK
MAX. 25mm (1")
COUNTERTOP
OVERHANG-DIM "X"
CABINET FACE
CABINET FACE
CUTOUT
FOLLOW THE SINK
CUTOUT LINE
VERTICALLY DOWN
ON THE CABINET
SINK CUTOUT
LINE
COUNTERTOP NOTCH
AND CABINET CUTOUT
INSTALLED VIEW (after completing steps 2 thru 7)
A. The cut allows the apron portion of the sink to fit in the countertop.
B. Cut the cabinet face per the diagram.
C. Drop in sink and check fit. Be sure apron edges touch the cabinet face.
MARKED LINE
OF SINK
MARKED LINE
OF SINK
10mm
(3/8")
FRONT EDGE
OF COUNTERTOP
CUT LINES
FOR NOTCH
SINK
CUTOUT
LINE
CABINET FACE
X
TOP VIEW
9-1/4
(235mm)
32-1/4
(819mm)
A
B

AB
Double Bowl
Trap
3
4
6
7
Connect supply lines to
faucet finger tight, and
carefully bend to engage
with the supply stops.
Tighten connections to
faucet for secure seal.
5
Connect drain assembly
hand tight to check
alignment. It may be
necessary to cut off part
of the tailpiece (area "A")
or part of the horizontal
leg of the trap (area "B").
Secure joint for water-
tight assembly.
790759-100 REV A 4
Apply a masking
tape outline 1/8"
outside traced out-
line as a guide for
application of silicone
sealant.
1/8"
Sink
Masking
Tape
Masking
tape
outline
Sink
outline
Cutout
Silicone
Sealant
Apply a generous portion of silicone sealant inside line
traced on countertop. Carefully lower sink into place
and press down firmly. Use guidelines for proper
positioning. Using water to dampen your finger,
remove excess sealant for a smooth even line. Apply
additional sealant if necessary to provide a uniform
bead from the rim of sink to the masking tape line as
shown. Carefully remove tape. Dampen finger and run
it slightly over the sealant to remove any high spots.
If inspection of the Corian Sink of this American Standard product, within ten years after
its initial purchase, confirms that it is defective in materials or workmanship, American
Standard will repair or, at its option, exchange the product for a similar model.
This warranty applies only to the original purchaser and installation of these products. All
labor and transportation costs or charges incidental to warranty service are to be borne by
the original consumer-purchaser.
This limited warranty does not apply to local building code compliance. Since local
building codes vary considerably, the purchaser of this product should check with a local
building or plumbing contractor to insure local code compliance before installation.
This warranty shall be void if the product has been fabricated or modified in a manner
inconsistent with the product as shipped by American-Standard; moved from its initial place
of installation; if it has been subjected to faulty maintenance, abuse, misuse, accident or
other damages; or if it was not installed in accordance with American Standard's
instructions.
American Standard's option to repair or exchange the product under this warranty does
not cover any labor or other costs of removal or installation, nor shall American Standard
be responsible for any other incidental or consequential damages attributable to a
product defect or to the repair or exchange of a defective product, all of which are
expressly excluded from this warranty. (Some states or provinces do not allow the
exclusion or limitation of implied warranties, so this exclusion may not apply to you.)
This warranty gives you specific legal rights. You may have other statutory rights that
vary from state to state of from province to province, in which case this warranty does not
affect such statutory rights.
In Canada:
American-Standard,
1401 Dupont Street,
Toronto, Ontario
Canada M6H 2B1
Toll free: [phone]
In Mexico:
Customer Service Manager
Ideal Standard, S.A. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
AMERICAN STANDARD TEN-YEAR LIMITED WARRANTY
CORIAN®SINK
For residents of the United States,
warranty information may also be
obtained by calling the following
toll free number: [phone]
Corian®Care &
MaintenanceTips
Use soapy water or
ammonia-based cleaner.
Wipe with damp cloth; towel dry.
Use an abrasive cleanser and
a green Scotch-Brite* pad.
Occasionally wipe surface with
diluted household bleach
(1 part water/1 part bleach).
Rub with Scotch-Brite* pad alone.
Cleaning
Most dirt
and stains
Water
marks
Difficult
stains
Disinfecting
Maintenance
*Registered trademark of the 3M Company
In the United States:
American Standard Inc.,
P. O. Box 6820
Piscataway, NJ 08855
Attention: Director of Consumer Affairs
2
Mount the faucet and
drain assembly on the
sink following the
manufacturer's
instructions.
Before applying the
sealant, place the sink
temporarily into the
cutout. Check for
alignment and clear-
ance, then trace
around the outside
edge of the sink as
a guide for installation location and application of
sealant. Remove sink.