Extreme Networks Mogul-100 User manual

Part number: 122024-00 Rev 01
Mogul–100 Quick Guide
The Mogul-100 connects an Ethernet network to a Very High speed Digital
Subscriber Line (VDSL), so it allows your Ethernet local area network
(LAN) to connect to a wide area network (WAN). The Mogul–100 is
compatible with the Extreme Networks VDSL module for the Alpine 3800
series switch. Your service provider is responsible for installing and
maintaining the Alpine 3800 and for establishing a WAN connection to
your facility over standard telephone-style wiring. The Extreme Networks
VDSL WAN connection looks like a standard RJ11 voice phone line, but
does not carry standard telephone calls, only network data.
Once your provider has established the wiring and activation for your site,
the Mogul-100 connects your provider’s WAN to your LAN.
Power supply
XM_003
Ethernet LAN RJ11 WAN line

The Mogul-100 power supply (AC adapter) comes with a detachable cable
designed to connect to your local AC electrical supply. The cable that is
permanently attached connects to the back of the Mogul-100 and supplies
the required DC power.
Connecting the Mogul-100
1. Connect the power supply to your local AC power.
2. Connect the power supply to the back of the Mogul-100. The green
POWER LED will light up.
3. Connect the RJ11 cable specified by your service provider to the WAN
port on the Mogul-100.
4. Connect the RJ45 Ethernet cable for your LAN to the LAN port.
Once the WAN cable is connected, the green LINK LED near the WAN port
will light up. It may take up to one minute for the LED to light up as the
Mogul-100 connects with the VDSL module on the Extreme Networks
Alpine 3800 series switch.
Once the LAN cable is connected, the green LINK LED near the LAN port
will light up. The amber ACT LEDs on both ports will light up as data is
transferred across the link.
XM_002
Ethernet connection to your LAN Connection to your service provider

The Mogul-100 can be attached to a wall. Use two screws, installed 90 mm
apart. Use a 6-32 round head screw (maximum shaft diameter 3.5 mm,
maximum head diameter 7 mm). If attaching to drywall, use drywall
anchors or install the screws into a wall stud.
Certification Marks
CE (European
Community) TUV/GS (German
Notified Body)
TUV/S
(Argentina) GOST (Russian Federation)
ACN 090 029 066
C-Tick (Australian
Communication
Authority)
Underwriters
Laboratories (USA
and Canada)
MIC (South
Korea) NOM (Mexican Official
Normalization,
Electronic
Certification and Normalization)
BSMI, Republic of Taiwan
Environmental Requirements
Operating Temperature 0° to 40° C

Storage Temperature -10°to 70°C
Operating Humidity 10% to 95% relative humidity,
noncondensing
Standards EN60068 to Extreme IEC68
schedule
Safety Agency Certifications UL 1950 3rd Edition, listed
EN60950:1992/A1-4:1997
plus ZB/ZC Deviations
IEC 950CB
Low Voltage Directive (LVD)
CSA 22.2#950-95
AS/NZS 3260
Electromagnetic Interference/
Compatibility (EMI/EMC) FCC CFR 47 part 15 Class B ICES-0003 A/C108.8-M1983
Class B
VCCI Class B
AS/NZS 3548
EN55022 Class B
CISPR 22 Class B
EN55024:1998 includes
IEC 61000-4-2, 3, 4, 5, 6, 8, 11
EN 61000-3-2, 3
CNS 13438 Class B
Power Supply
AC Line Frequency 47 Hz to 63 Hz
Input Voltage Options 90 VAC to 264 VAC, auto-ranging
Current Rating 115 VAC 0.4 A / 230 VAC 0.2A