AMG AMG5513 User manual

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 1 of 8 AMG5513 Instruction Sheet D17297-
00.doc
AMG5513
Instruction Manual
Transmit Unit with one Bi-directional Data Channel and one
Bi-directional Alarm for a Singlemode Fibre Link
The AMG5513 is a compact standalone transmit unit designed to transmit and receive 1 data signal
plus 1 Bi-directional alarm over one Singlemode optical fibre.
The AMG5513 is designed to be powered using an AMG2001 standalone power supply.
The AMG5513 is designed to operate with an AMG5514 / AMG5514R single channel or AMG5524 /
AMG5524R dual channel receive unit in a point to point configuration. The R suffix in the partno.
indicates a rackmount configuration.

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 2 of 8 AMG5513 Instruction Sheet D17297-
00.doc
Contents
Introduction 3
Unit Functional Schematic..............................................................................................................3
Optical Connection.........................................................................................................................3
Connections 4
Optical Connections Singlemode....................................................................................................4
Power Connection..........................................................................................................................4
Data and Alarm Channel Connections............................................................................................4
Front Panel Indicators 5
Power / Opto LED..........................................................................................................................5
Low Speed Data LEDs...................................................................................................................5
Alarm LEDs ...................................................................................................................................5
Data and Alarm Channel Configuration 6
Data Channel Configuration...........................................................................................................6
Data Interface Connections............................................................................................................6
Alarm Channel Configuration 7
Bi-directional Alarm Interface Connections.....................................................................................7
Physical Information 8
Dimensions....................................................................................................................................8
Mounting Details............................................................................................................................8
Safety 8
Maintenance and Repair 8

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 3 of 8 AMG5513 Instruction Sheet D17297-
00.doc
Introduction
Unit Functional Schematic
The
AMG5513
transmits 1 data channel
and 1 uni-directional alarm signal to the
AMG5514 receive unit.
It also receives 1 data channel and 1 Bi-
directional alarm transmitted from the
AMG5514.
Optical Connection
The AMG5513 connections are illustrated in the following example which shows an AMG5513
transmit unit together with an AMG5514 receive unit configured as a single channel point to point
system.

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 4 of 8 AMG5513 Instruction Sheet D17297-
00.doc
Connections
Optical Connections Singlemode
No. of Optical Connections................. 1
Optical Fibre...................................... Singlemode
Connector.......................................... SC/PC
Primary Optical Launch Power........... -10dBm
Transmit Wavelength......................... 1310nm
Primary Optical Sensitivity.................. -30dBm
Receive Wavelength.......................... 1510nm
Minimum Optical Dynamic Range ...... 20dB.
Power Connection
Connector Type................................. Removable 2-pin, 3.81mm, Screw Terminal
Connector Partno............................... Phoenix 1803578
Supply Voltage................................... +12 to +15Vdc
Maximum Power................................ 1.5 Watts
Data and Alarm Channel Connections
No. of Data Channels......................... 1
No. of Alarm Channels....................... 1
Connector.......................................... Removable 8-pin, 3.81mm, Screw Terminal
Connector Partno............................... Phoenix 1803633
Data Interface.................................... RS-232, RS-422 or R-S485. Selected by slide switch above the
BNC connector.
RS-232 –Switch Position - Left
RS-422 –Switch Position - Centre
RS-485 –Switch Position - Right
Alarm Input........................................ Contact Closure pull-up is 330R to +3V3
Alarm Output ..................................... Solid-state Relay, maximum 150mA at 125Vac/dc, Ron < 6.5Ω

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 5 of 8 AMG5513 Instruction Sheet D17297-
00.doc
Front Panel Indicators
Power / Opto LED
Power / Opto......................................Green - Unit powered, Opto sync.
Red - Unit powered, no Opto sync.
Off - No power applied to unit
Low Speed Data LEDs
Data Present IN (RS485 or RS422).... Green - logic zero (+V, -V) present on IN+, IN-
Red - logic one (-V,V+) present on IN+, IN-
Off - tri-state off or no connection on IN+, IN-
Data Present IN (RS232)................... Green - logic zero (+V) present on input IN+
Red - logic transitions present on input IN+
Off - logic one (-V) present on input IN+
IN corresponds to the data signals being transmitted onto the optical fibre.
Data Present OUT (RS485 or RS422) Green - logic zero (+V,-V) present on OUT+, OUT-
Red - logic one (-V,+V) present on OUT+, OUT-
Off - tri-state off or no connection on OUT+, OUT-
Data Present OUT (RS232)................ Green - logic zero (+V) present on OUT+
Red - logic transitions present on OUT+
Off - logic one (-V) present on OUT+
OUT corresponds to the data signals being received from the optical fibre.
Alarm LEDs
ALARM IN..........................................Green - Alarm ON / Contacts closed.
Off - Alarm OFF / Contacts open.
ALARM OUT......................................Green - Alarm ON / Contacts closed.
Off - Alarm OFF / Contacts open.

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 6 of 8 AMG5513 Instruction Sheet D17297-
00.doc
Data and Alarm Channel Configuration
Data Channel Configuration
The low speed data channel provides an RS-232, RS-422 (full duplex, four wire) or RS-485 (half
duplex, two wire) interface defined by the mode switch on the front panel. The data channel as
shipped from the factory is set up for RS-485 operation unless otherwise requested.
The data input for both the RS-485 and the RS-422 modes detects a tri-state input condition by
monitoring the differential voltage level across the input. A differential level below 600mV positive or
negative will be detected as a tri-state condition. A level above 600mV positive or negative will be
detected as a logic 1 or logic zero respectively. It is important therefore to terminate the RS-485 bus or
the RS-422 input bus using 120Ωif a pre-bias is present on the RS-485 or RS-422 bus.
A large number of third party equipment manufacturers apply a pre-bias on their RS-485 bus. This pre-
bias is applied by pulling one arm of the RS-485 bus high (+5 volts) and the other arm low (0 volts)
using high value resistors within the third party equipment. In order to ensure that the AMG equipment
detects a tri-state condition, then these resistors should have a value above 5kΩ. If the third party
bias resistors are less than 750Ωthe bus can be multiple terminated as required to ensure that a tri-
state level is detected.
The system detects a tri-state input condition on the data channel bus when in RS-485 or RS-422
mode.
Data Interface Connections
Connector
Pin No.
Data Channel
RS-485
[switch right] RS-422 [switch mid] RS-232 [switch left]
1IN + (A) IN
2IN - (B)
3GND GND GND
4
5
6
7IN/OUT + (A) OUT + (A)
8IN/OUT - (B) OUT - (B) OUT
Note: (A) or (B) in brackets in the above table refers to RS-485 / RS-422 data specification.

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 7 of 8 AMG5513 Instruction Sheet D17297-
00.doc
Alarm Channel Configuration
The AMG5513 provides 1 Bi-directional alarm output / contact closure input.
The alarm input is typically connected to a contact closure switch. An ALARM IN+ input incorporates a
330R pull-up resistor to the internal +3V3 supply.
The alarm output can receive an on/off signal from an AMG5514 and is typically used to convey
contact closure status. An alarm output uses a solid-state relay, with a maximum load current of
150mA at 125Vac/dc and Ron < 6.5Ω.
Bi-directional Alarm Interface Connections
Connector Pin
No.
Alarm Interface
Alarm IN Alarm OUT
1
2
3GND
4ALARM IN +
5ALARM OUT -
6ALARM OUT +
7
8

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 8 of 8 AMG5513 Instruction Sheet D17297-
00.doc
Physical Information
Dimensions
Height................................................ 56mm
Width................................................. 55mm (excluding connectors)
Depth................................................. 25mm
Weight............................................... 200grams
Mounting Details
The unit is designed to be mounted using the clip holder supplied, which can be fixed to a wall or
panel using 2 off 4mm screws.
Safety
AMG Optical Fibre Products use Class 1 laser systems in accordance with EN 60825-2:2000.
It is always advisable to follow good practice when working with optical fibre systems. This includes:
§Do not stare with unprotected eyes or with any unapproved collimating device at fibre
ends or connector faces, or point them at other people.
§Use only approved filtered or attenuating viewing aids
For other safety issues and advice on good practice associated with optical fibre systems, please see
EN 60825-2:2000 or your local safety officer.
Maintenance and Repair
There are no user serviceable parts within AMG products. See unit data sheet for full specification.
In case of problem or failure, please call your local support centre or contact: AMG Systems Ltd. at
3 The Omega Centre, Stratton Business Park, Biggleswade, Beds., SG18 8QB, UK.
Phone [phone]
Technical Support [phone]
Email [e-mail]