Amit RB-SW00A/NR1 User manual

rb-sw00anr1_g_en_100
RB-SW00A/NR1
Industrial Ethernet switch
Operation manual
Version 1.00

RB-SW00A/NR1
rb-sw00anr1_g_en_100 2/18
AMiT, spol. s r.o. does not provide any warranty concerning the contents of this
publication and reserves the right to change the documentation without
obligation to inform any body or authority about it.
This document can be copied and redistributed under following conditions:
1. The whole text (all pages) must be copied without any changes.
2. All redistributed copies must retain the AMiT, spol. s r.o. copyright notice
and any other notices contained in the documentation.
3. This document must not be distributed for purpose making of profit.
The names of products and companies used herein can be trademarks or
registered trademarks of their respective owners.
AMiT is a registered trademark.
Copyright (c) 2013, AMiT, spol. s r. o.
Producer: AMiT, spol. s r. o.
Naskové 3/1100, 150 00 Praha
www.amit.cz
Technical support: [email protected]

RB-SW00A/NR1
3/18 rb-sw00anr1_g_en_100
Contents History of revisions.........................................................................................4
Related documentation...................................................................................4
1. Introduction..........................................................................................5
2. Technical parameters..........................................................................6
2.1. Dimensions.....................................................................................................7
2.2. Recommended drawing symbol .....................................................................8
3. Conformity assessment ......................................................................9
3.1. Other tests....................................................................................................10
4. Power supply......................................................................................11
5. Communication lines.........................................................................12
5.1. Ethernet interface.........................................................................................12
6. Location of LEDs and connectors....................................................13
6.1. Connectors and terminals layout..................................................................13
6.2. LEDs layout..................................................................................................14
7. Mounting.............................................................................................15
7.1. Installation rules............................................................................................15
8. Ordering information and completion .............................................16
8.1. Completion ...................................................................................................16
9. Maintenance .......................................................................................17
10. Waste disposal...................................................................................18

RB-SW00A/NR1
rb-sw00anr1_g_en_100 4/18
History of revisions
Document name: rb-sw00anr1_g_en_100.pdf
Author: Viktor Csörgő
Revision
Date
Changes
100
18. 11. 2013
New document
Related documentation
1. Datasheet RB-SW00A/NR1
file: rb-sw00anr1_d_en_xxx.pdf
2. Application Note AP0037 –Principles of using Ethernet network
file: ap0037_en_xx.pdf
3. Application Note AP0051 –Ethernet network cabling on rolling stock
file: ap0051_en_xx.pdf

RB-SW00A/NR1
5/18 rb-sw00anr1_g_en_100
1. Introduction
RB-SW00A/NR1 is an industrial Ethernet switch without Power over Ethernet
(PoE). Switch is designed for using on rolling stock.
4 integrated industrial 5+1 port switches
Communication rate 10/100 Mbps on ports X12 to X16, X22 to X26, X32 to
X36, X42 to X46
Communication rate 100 Mbps on ports X11, X21, X31 and X41 (Uplink)
Connection through RJ45 connectors
Power supply +24 V DC
Design according to EN 50155:2007
Basic features

RB-SW00A/NR1
rb-sw00anr1_g_en_100 6/18
2. Technical parameters
Number of ports
24
Communication rate X11
X22 to X26
100 Mbps
10/100 Mbps
Communication rate X21
X22 to X26
100 Mbps
10/100 Mbps
Communication rate 31
X32 to X36
100 Mbps
10/100 Mbps
Communication rate X41
X42 to X46
100 Mbps
10/100 Mbps
Galvanic separation
Yes
Galvanic separation strength
500 V AC /1 minute *)
Connection point
RJ45 connector, according to IEEE 802.3
Recommended cabling
STP CAT5
Maximum segment length
100 m
*) Insulation must not be used for dangerous voltage separation.
Nominal power supply voltage
24 V DC
Power supply voltage range
16.6 V to 33.6 V DC
Power consumption
Max. 0.6 A at 24 V DC
Inrush peak current
Max. 12 A
Galvanic separation
No
Connection point
WAGO X-COM 769 connector
Wire cross section
0.75 mm2to 4 mm2
Mechanical design
Metal case
Colour
RAL 7035
Mounting
4 × hole ø 6 mm
Ingress protection rate
IP20
Weight –netto
–brutto
1.30 kg ±5 %
1.42 kg ±5 %
Dimensions (w × h × d)
(92 × 193 × 88) mm
Unit overall mass of plastics
260 g ±5 %
Included mass of self-
extinguishing plastics
260 g ±5 %
Device does not contain
PUR, PVC, Asbestos
Device conforms
2011/65/EU (ROHS)
1907/2006EU (REACH)
Operating temperature range
-40 °C to 70 °C
Storage temperature range
-40 °C to 70 °C
Maximum ambient humidity
< 95 % non-condensing
Expected MTBF
500 000 h
Expected lifetime
15 years
None
Ethernet
Note
Power supply
Mechanics
Dangerous
materials
Temperatures
Others
Components
with reduced
lifetime

RB-SW00A/NR1
7/18 rb-sw00anr1_g_en_100
Equipment is intended to operate up to 1 400 m above the sea level.
Equipment is designed to meet the Temperature Class TX.
According to EN 61373:2010 standard, the equipment is classified in terms of vibra-
tions into Category 1, Class B (mounting to vehicle body).
Permissible supplying voltage drop-outs duration: max 10 ms (Class S2 according to
Chapter 3.1.1.2 of EN 50155:2007).
For supply voltage switching are permissible conditions of C1 and C2 Class.
The equipment meets the SIL0 classification according to EN 50129:2003 Railway
applications –Communication, signalling and processing systems –Safety-related
electronic systems for signalling.
2.1. Dimensions
92
67
158 174 193
4x o 6
88
124
Fig. 1 - RB-SW00A/NR1 dimensions
Claims EN
50155:2007 3
Safety
classification

RB-SW00A/NR1
rb-sw00anr1_g_en_100 8/18
2.2. Recommended drawing symbol
Following drawing symbol is recommended for industrial Ethernet switch
RB-SW00A/NR1. Drawing symbol is available for download in DWG, DXF and
WMF formats at www.amit-transportation.cz web site.
ETH
ETH
ETH
ETH
ETH
ETH
X15
X12
RB-SW00A/NR1
X16
PWR
PE
GND
Vcc
X7
1
2
3
X13
X14
X11
UPLINK
RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
ETH
ETH
ETH
ETH
ETH
ETH
X25
X22
X26
X23
X24
X21
UPLINK
RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
ETH
ETH
ETH
ETH
ETH
ETH
X35
X32
X36
X33
X34
X31
UPLINK
RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
ETH
ETH
ETH
ETH
ETH
ETH
X45
X42
X46
X43
X44
X41
UPLINK
RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
Fig. 2 - Recommended drawing symbol for RB-SW00A/NR1

RB-SW00A/NR1
9/18 rb-sw00anr1_g_en_100
3. Conformity assessment
The equipment meets the requirements of NV616/2006 Czech governmental
decree. Conformity assessment procedure was carried out in accordance with
harmonized standard EN 61326-1:2006 and EN 50121-3-2:2006.
Tested in accordance
with standard
Type of test
Classificat
ion
EN 55011:2009
Industrial, scientific and medical equipment –
Radio-frequency disturbance characteristics –
Limits and methods of measurement
Complies *)
EN 61000-4-2:2009
Electromagnetic compatibility (EMC) –
Part 4-2: Testing and measurement
techniques –Electrostatic discharge immunity
test
Complies *)
EN 61000-4-3:2006
Electromagnetic compatibility (EMC) –
Part 4-3: Radiated, radio-frequency,
electromagnetic field immunity test,
800 MHz to 1000 MHz
20 V/m **)
EN 61000-4-3:2006
Electromagnetic compatibility (EMC) –
Part 4-3: Radiated, radio-frequency,
electromagnetic field immunity test,
1000 MHz to 2100 MHz
10 V/m **)
EN 61000-4-3:2006
Electromagnetic compatibility (EMC) –
Part 4-3: Radiated, radio-frequency,
electromagnetic field immunity test,
2100 MHz to 2500 MHz
5 V/m **)
EN 61000-4-4:2004
Electromagnetic compatibility (EMC) –
Part 4-4: Testing and measurement
techniques –Electrical fast transient/burst
immunity test, power supply
±4 kV **)
EN 61000-4-4:2004
Electromagnetic compatibility (EMC) –
Part 4-4: Testing and measurement
techniques –Electrical fast transient/burst
immunity test, communication
±4 kV **)
EN 61000-4-5:2006
Electromagnetic compatibility (EMC) –
Part 4-5: Testing and measurement
techniques –Electrostatic discharge immunity
test, power supply.
±4 kV **)
EN 61000-4-5:2006
Electromagnetic compatibility (EMC) –
Part 4-5: Testing and measurement
techniques –Electrostatic discharge immunity
test, communication lines
±3 kV **)
EN 61000-4-6:2009
Electromagnetic compatibility (EMC) –
Part 4-6: Testing and measurement tech-
niques –Immunity to conducted disturbances,
induced by radio-frequency fields
10 V **)
*) Device complies with EN 50121-3-2:2006 2. This device belongs to A Class
according to EN 61326-1:2006 standard and complies with EN 55011
standard.
**) Device complies with both standards in wider range then the standards
require.

RB-SW00A/NR1
rb-sw00anr1_g_en_100 10/18
3.1. Other tests
Tested in accordance
with standard
Type of test
Classification
EN 61000-4-29:2000
Electromagnetic compatibility (EMC) –
Part 4-29: Testing and measurement
techniques –Voltage dips, short
interruptions and voltage variations
immunity tests
Complies
EN 50155:2007
Electronic equipment used on rolling
stock.
Complies
EN 50121-3-2:2006
Electromagnetic compatibility (EMC) –
Part 3-2: Rolling stock –equipment
Complies
EN 61373:2010
Railway applications –Rolling stock
equipment –Shock and vibration tests.
Complies
EN 60068-2-1:2007
Environmental testing –Part 2-1: Test A:
Cold
Complies
EN 60068-2-2:2007
Environmental testing –Part 2-2: Test B:
Dry heat
Complies

RB-SW00A/NR1
11/18 rb-sw00anr1_g_en_100
4. Power supply
Industrial Ethernet switch RB-SW00A/NR1 can be powered only by DC power
supply.
Industrial Ethernet switch RB-SW00A/NR1 can be supplied by current DC
power supplies made by AMiT.
X7
Vcc (3)
GND (2)
PE (1)
Fig. 3 - Ethernet switch RB-SW00A/NR1 power supply
Terminal
Label
Meaning
1
PE
Device chassis
2
GND
Power supply, ground
3
Vcc
Power supply, +24 V DC
RB-SW00A/NR1
1
2 3
PE
GND
Vcc
X7
PWR
230 V stř.
7
6
5
4
GND
GND
+24V
+24V
L
PE
N
1
2
3
AZ1 24V/2,5A
24 V ss.
Fig. 4 - Wiring scheme of X7 connector –power supply
Power supply
24 V DC
Wiring of X7
connector
Wiring
example

RB-SW00A/NR1
rb-sw00anr1_g_en_100 12/18
5. Communication lines
5.1. Ethernet interface
Industrial Ethernet switch RB-SW00A/NR1:
4 integrated 6 port Ethernet switches.
24 ports which meets the IEEE 802.3 standard.
Ports X12 to X16, X22 to X26, X32 to X36, X42 to X46 support communica-
tion rate 10/100 Mbps
Ports X11, X21, X31 and X41 support communication rate 100 Mbps
All ports enable the Half-duplex or Full-duplex communication
All ports operate with direct or cross-wired cable
Recommended cabling: CAT5, shielded.
Line state indication separately for each port.
Fig. 5 - Meaning of LED indicators for Ethernet
LED
Status
Meaning
LINK
Lights
Cable connection detected
ACT
Blinks
Running communication
Details about Ethernet network are stated in Application Note AP0037.
Meaning of
LED
indicators for
Ethernet
Note

RB-SW00A/NR1
13/18 rb-sw00anr1_g_en_100
6. Location of LEDs and connectors
6.1. Connectors and terminals layout
Fig. 6 - Connectors and terminals location
Connector
Meaning
Connector
Meaning
X11
Ethernet port 1 –Uplink
X31
Ethernet port 1 –Uplink
X12
Ethernet port 2
X32
Ethernet port 2
X13
Ethernet port 3
X33
Ethernet port 3
X14
Ethernet port 4
X34
Ethernet port 4
X15
Ethernet port 5
X35
Ethernet port 5
X16
Ethernet port 6
X36
Ethernet port 6
Connector
Meaning
Connector
Meaning
X21
Ethernet port 1 –Uplink
X41
Ethernet port 1 –Uplink
X22
Ethernet port 2
X42
Ethernet port 2
X23
Ethernet port 3
X43
Ethernet port 3
X24
Ethernet port 4
X44
Ethernet port 4
X25
Ethernet port 5
X45
Ethernet port 5
X26
Ethernet port 6
X46
Ethernet port 6
Connector
Meaning
X7
Power supply
Terminal
Meaning
1
Tx+
2
Tx-
3
Rx+
4
Not used
5
Not used
6
Rx-
7
Not used
8
Not used
Connectors
specification
Terminals
meaning
X11 to X16
X21 to X26
X31 to X36
X41 to X46

RB-SW00A/NR1
rb-sw00anr1_g_en_100 14/18
6.2. LEDs layout
Industrial Ethernet switch contains single LED indicator.
LED PWR
Fig. 7 - LEDs layout
LED
Status
Meaning
PWR
Lights
Power supply OK
Meaning of
LEDs

RB-SW00A/NR1
15/18 rb-sw00anr1_g_en_100
7. Mounting
Industrial Ethernet switch RB-SW00A/NR1 is intended for mounting with four
holes with 6 mm diameter. Industrial switch can be mounted in arbitrary
position.
67
174
4x o 6
Fig. 8 - Mounting RB-SW00A/NR1 switch
7.1. Installation rules
PE terminal of power supply connector must be connected with local installation
earthing terminal. All PE connections must be realized with as low as possible
impedance. Technical parameters of industrial Ethernet switch are guaranteed
only when these wiring rules are applied.
The cables or individual wires being connected to Ethernet switch must be
protected against mechanical stress. Cables or individual wires connected to
Ethernet switch must be protected against mechanical stress by binding to the
solid installation part. Length of cable or individual wire between last binding
point and the Ethernet switch connector should not exceed 15 cm.
Note

RB-SW00A/NR1
rb-sw00anr1_g_en_100 16/18
8. Ordering information and completion
RB-SW00A/NR1
Complete, see chapter Completion
8.1. Completion
Part
Quantity
Industrial Ethernet switch
1
Connector counterpart WAGO 769-103/021-000
1
Operation manual
1
Routine testing protocol
1
Insulation testing protocol
1
Warranty certificate
1
RB-SW00A/NR1

RB-SW00A/NR1
17/18 rb-sw00anr1_g_en_100
9. Maintenance
With exception of cleaning the device requires no periodic control nor
maintenance.
Depending on equipment usage, the dust is to be removed occasionally from
equipment. The equipment can be cleaned by dry soft brush or vacuum cleaner,
only when turned-off and disassembled.
Inspection must be carried out once every five years.
The maintenance mentioned above can be performed by manufacturer or
authorized service only!
Cleaning
Note

RB-SW00A/NR1
rb-sw00anr1_g_en_100 18/18
10. Waste disposal
The disposal of electronic equipment is subject to the regulations on handling
electrical waste. The equipment must not be disposed off in common public
waste. It must be delivered to places specified for that purpose and recycled.
Electronics
disposal