Amprobe AMP-25 User manual

Mini-Clamp
www. .com [e-mail]1.800.561.8187

AMP-25
User Manual
®
English
www. .com [e-mail]1.800.561.8187

AMP-25 Mini-Clamp
www. .com [e-mail]1.800.561.8187

AMP-25 Mini-Clamp
www. .com [e-mail]1.800.561.8187

AUTO:
A:
HOLD:
LPF:
INRUSH:
CAT III
www. .com [e-mail]1.800.561.8187

Measurement Category III (CAT III)
Warning: Read Before Using
www. .com [e-mail]1.800.561.8187

www. .com [e-mail]1.800.561.8187

Warning
Press button to turn ON the meter (the
default is auto AC/DC A mode). Press > one
second to turn OFF.
Press
Press
OFF
>1 Sec
Press button to turn ON or to turn OFF
LCD backlight. The backlight automatically
turns OFF after approximately 30 seconds.
Press
www. .com [e-mail]1.800.561.8187

Press button to select AC A or DC A mode.
Press button > one second to return to
AUTO AC/DC A mode.
Press button to enter Low Pass Filter
mode (LPF is displayed). Press a second time
to enter Inrush mode (INRUSH is displayed).
Press again to exit the function.
/ Press button to activate non-contact
voltage mode. Press a second time to exit
non-contact voltage mode.
Press / button > two seconds to
clear DC A reading from the display ( is
displayed) and establish a baseline for DC A.
Press button > two seconds again to exit
this mode.
1. ZERO mode can be activated in DC A and
DC A of Auto DC/AC A mode only.
2. When ZERO is activated (symbol is
displayed in DC A and Auto DC A mode
only), the offset residual value will not be
reset until the Meter is turned OFF.
3. ZERO can be activated if residual value < 6
A in DC A mode, < 6 A DC and <0.1 A AC in
Auto DC/AC A mode.
HOLD Press HOLD button to freeze the display
reading (HOLD is displayed) and releases the
reading when pressed a second time.
Warning
www. .com [e-mail]1.800.561.8187

Warning
Caution
During current measurement keep the jaws away from
other current carrying devices such as transformers,
motors or energized wires, as they may negatively
influence accuracy of the measurement.
Auto
Press > 1 Sec
Press
Press
CAT III 600 V
Tactile barrier
www. .com [e-mail]1.800.561.8187

/
0A
LPF
Press
100A/1KHz
INRUSH
www. .com [e-mail]1.800.561.8187

INRUSH
www. .com [e-mail]1.800.561.8187

HOLD
Warning
To avoid possible electric shock or personal injury, when
Display HOLD is activated, be aware that the display will
not change when you apply a different current.
HOLD
0A
Press
HOLD
DC 100A
HOLD
Note: During data hold, the display flashes if the measured
signal is 50 counts larger than the display reading. The
Meter cannot detect across the AC and DC current.
www. .com [e-mail]1.800.561.8187

Disable auto power off:
RoFF
° ° ° °
° ° ° °
° ° ° °
www. .com [e-mail]1.800.561.8187

°
° °
www. .com [e-mail]1.800.561.8187

www. .com [e-mail]1.800.561.8187

www. .com [e-mail]1.800.561.8187

www. .com [e-mail]1.800.561.8187

To avoid shock, injury, or damage to the Meter, disconnect
test leads before opening case.
Replacing BATTERY follow below steps:
4
3
www. .com [e-mail]1.800.561.8187

AMP-25
Guide d’utilisation
®
All rights reserved. Printed in Taiwan
Français
www. .com [e-mail]1.800.561.8187