AMS TMD2635 User manual

Product
Document
Published by
ams OSRAM Group

Quick Start Guide
QG000142
TMD2635
TMD2635 EVM
Miniature Proximity Sensor Module
v2-00 •2022-May-19

Document Feedback
TMD2635 ●TMD2635 EVM
Content Guide
Quick Start Guide •PUBLIC
QG000142 •v2-00 • 2022-May-19
9│2
Content Guide
1Out of the Box................................ 3
2Software Installation ..................... 4
3Connect Hardware......................... 7
4Start the Application ..................... 8
5Uninstall Application..................... 9

Document Feedback
TMD2635 ●TMD2635 EVM
Out of the Box
Quick Start Guide •PUBLIC
QG000142 •v2-00 • 2022-May-19
9│3
1 Out of the Box
For a detailed description of the TMD2635, please refer to User Guide:
●TMD2635_UG000453
Each TMD2635 Evaluation Kit comes with the following components:
Figure 1 :
Evaluation Kit Contents
No.
Item
Description
1
TMD2635 Daughter Card
PCB with TMD2635 sensor installed
2
EVM Controller Board
Used to communicate USB to I2C
3
USB Cable (A to Micro-B)
Connects EVM controller to PC
4
Flash Drive
Includes application installer and documents
4
3
2
1

Document Feedback
TMD2635 ●TMD2635 EVM
Software Installation
Quick Start Guide •PUBLIC
QG000142 •v2-00 • 2022-May-19
9│4
2 Software Installation
1. Plug the ams flash drive into an unused USB port
2. Double-click the Setup.exe file on the flash drive, or click Start > Run and type E:setup.exe and
press Enter. IMPORTANT: Use the appropriate drive letter in the above command to install the
software. Flash Drive will commonly be assigned the next available drive letter for example C:
hard drive, D: CD-ROM, E: flash drive
3. The Setup Wizard will open and guide you through the installation of the TMD2635 host
software, (Figure 2 through Figure 8)
4. The EVM Controller board requires the installation of FTDI CDM drivers. If these drivers are not
installed on your machine, this setup will automatically launch the installer for the FTDI drivers.
5. At the end of the installation, click Finish to exit the setup.
Figure 2:
Welcome Screen
Figure 3:
Liability Disclaimer

Document Feedback
TMD2635 ●TMD2635 EVM
Software Installation
Quick Start Guide •PUBLIC
QG000142 •v2-00 • 2022-May-19
9│5
Figure 4:
Select Installation Folder
Figure 5:
Select Start Menu Folder
Figure 6:
Installation in Progress
Figure 7:
Information Screen

Document Feedback
TMD2635 ●TMD2635 EVM
Software Installation
Quick Start Guide •PUBLIC
QG000142 •v2-00 • 2022-May-19
9│6
Figure 8:
Installation Completed Successfully

Document Feedback
TMD2635 ●TMD2635 EVM
Connect Hardware
Quick Start Guide •PUBLIC
QG000142 •v2-00 • 2022-May-19
9│7
3 Connect Hardware
Plug the TMD2635 daughterboard into the controller board (Figure 1). Always use ESD procedures
when handling the EVM.
Using the enclosed USB cable, plug the micro-B connector into the EVM module. Using the other end
of the cable, plug the USB A-connector into a USB port on the computer.
When the USB cable is connected, the green LED should light on power up to indicate that power is
being received via the USB interface, and the controller board processor is running. If the green LED
does not light, check the USB cable connections; unplug the USB cable and try again. If the green
LED still does not light, check the PC for USB error messages. When the software application is run, it
will turn off the LED.

Document Feedback
TMD2635 ●TMD2635 EVM
Start the Application
Quick Start Guide •PUBLIC
QG000142 •v2-00 • 2022-May-19
9│8
4 Start the Application
To start the application select ams-OSRAM > TMD2635 EVM > TMD2635 EVM on the system menu.
The default installation directory depending on the device and the operating system you are using is:
C:\Program Files\ ams-OSRAM \TMD2635_EVM (Windows 32-bit operating systems)
C:\Program Files (x86)\ ams-OSRAM \TMD2635_EVM (Windows 64-bit operating systems)
A different install path may be selected by the user during the install (Figure 4). When started, the
TMD2635 window will open on the PC and automatically connect to the hardware.

Document Feedback
TMD2635 ●TMD2635 EVM
Uninstall Application
Quick Start Guide •PUBLIC
QG000142 •v2-00 • 2022-May-19
9│9
5 Uninstall Application
To remove the software from your computer (Figure 9), select ams-OSRAM > TMD2635 EVM >
Uninstall TMD2635 EVM or use the Windows Control Panel.
Figure 9:
Remove Installation
Headquarters
ams-OSRAM AG
Tobelbader Strasse 30
8141 Premstaetten
Austria, Europe
Tel: [phone]
Please visit our website at www.ams.com
Buy our products or get free samples online at www.ams.com/Products
Technical Support is available at www.ams.com/Technical-Support
Provide feedback about this document at www.ams.com/Document-Feedback
For sales offices, distributors and representatives go to www.ams.com/Contact
For further information and requests, e-mail us at [email protected]
Copyright ams-OSRAM AG. Trademarks Registered. All rights reserved. The material herein may not be reproduced, adapted,
merged, translated, stored, or used without the prior written consent of the copyright owner.
ams-OSRAM AG shall not be liable to recipient or any third party for any damages, including but not limited to personal injury,
property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages,
of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or
liability to recipient or any third party shall arise or flow out of ams-OSRAM AG rendering of technical or other services.