Analog Devices EVAL-ADV7282MEBZ User manual

ADV7282-M
Installation Guide
Rev. A
March 2013

ADV7282-M Installation Guide
Rev. A, March 2013 2
TABLE OF CONTENTS
Introduction to the ADV7282-M Installation Guide...................................................................................................... 3
Audience..........................................................................................................................................................................................3
Disclaimer .......................................................................................................................................................................................3
Trademark and Service Mark Notice...........................................................................................................................................3
1. Description of the ADV7282-M Evaluation Board................................................................................................ 4
2. Setting Up the ADV7282-M Evaluation Board...................................................................................................... 6
2.1. Download and Install an FTP Client ...........................................................................................................................6
2.2. Download ADV7282-M Files From ADI FTP Site....................................................................................................6
2.3. Install the DVP Eval Program.......................................................................................................................................7
2.4. Load the ADV7282-M Script Files...............................................................................................................................8
2.5. Power up the ADV7282-M Evaluation Board ............................................................................................................9
2.6. Program the ADV7282-M Evaluation Board .............................................................................................................9
List of Figures.................................................................................................................................................................... 12
List of Tables ..................................................................................................................................................................... 12
Revision History ............................................................................................................................................................... 12

ADV7282-M Installation Guide
Rev. A, March 2013 3
INTRODUCTION TO THE ADV7282-M INSTALLATION GUIDE
The ADV7282-M Installation Guide describes the ADV7282-M evaluation board; and provides instructions for setting up the ADV7282-
M evaluation board, installing the required ADV7282-M software, and running the scripts needed to operate the ADV7282-M evaluation
board.
AUDIENCE
The ADV7282-M Installation Guide is intended for the use of the person installing an ADV7282-M evaluation board.
DISCLAIMER
The information contained in this document is proprietary of Analog Devices Inc. (ADI). This document must not be made available to
anybody other than the intended recipient without the written permission of ADI.
The content of this document is believed to be correct. If any errors are found within this document, or if clarification is needed, contact
the local FAE.
TRADEMARK AND SERVICE MARK NOTICE
The Analog Devices logo is a registered trademark of Analog Devices, Inc. All other brand and product names are trademarks or service
marks of their respective owners.

ADV7282-M Installation Guide
Rev. A, March 2013 4
1. DESCRIPTION OF THE ADV7282-M EVALUATION BOARD
Analog video is fed into the analog inputs (Ain1 to Ain6) of the ADV7282-M evaluation board. The ADV7282-M evaluation board can be
configured to receive many different analog video formats (refer to Table 1). The analog video is fed into the ADV7282-M video decoder
which converts it into a MIPI CSI-2 output stream.
The MIPI CSI-2 output of the ADV7282-M consists of one differential data lane (D0+ and D0-) and one differential clock lane (Clk+ and
Clk-). These are output to the SMA connectors on the evaluation board.
Table 1. Acceptable Analog Video Input Formats to ADV7282-M Evaluation Board
Ain1 Ain2 Ain3 Ain4 Ain5 Ain6
Single-ended CVBS
(NTSC, PAL, SECAM)
SE CVBS1 SE CVBS2 [1] [1] [1] [1]
Differential CVBS [2] [2] DIFF CVBS1+ DIFF CVBS1- DIFF CVBS2+ DIFF CVBS2-
S-Video (YC)
S_Video1(Y)
S_Video1 (C)
[3]
[3]
[3]
[3]
YPbPr [4] [4] [4] No No No
Note: The shaded areas in Table 1indicate that modifications need to be made to the ADV7282-M evaluation board before that particular
video input standard can be input to that particular analog input pin.
[1] These inputs can be configured to receive single-ended CVBS, but the user needs to change some resistor values on the ADV7282-M
evaluation board.
[2] Ain1 and Ain2 can be configured to receive differential CVBS, but the user needs to change some resistor values on the ADV7282-M
evaluation board.
[3] These inputs can be configured to receive YC (S-video), but the user needs to change some resistor values on the ADV7282-M
evaluation board.
[4] These inputs can be configured to receive component (YPbPr), but the user needs to change some resistor values on the ADV7282-M
evaluation board.

ADV7282-M Installation Guide
Rev. A, March 2013 5
Figure 1. ADV7282-M Evaluation Board
LED D6: Indicates
power supply is ok
7.5V Power
Supply
Connector
USB
Connector
LED D7:
Indicates USB
connection
is ok
Ain1:
Single-ended
analog input
Positive MIPI
CSI-2 data
output lane
SMA connector
Positive MIPI
CSI-2 clock
output lane
SMA connector
ADV7282-M
Video Decoder
Negative MIPI
CSI-2 data
output lane
SMA connector
Negative MIPI
CSI-2 clock
output lane
SMA connector
Ain2:
Single-ended
analog input
Ain3 and 4:
Differential
analog inputs
Ain5 and 6:
Differential
analog inputs
I2C Headers

ADV7282-M Installation Guide
Rev. A, March 2013 6
2. SETTING UP THE ADV7282-M EVALUATION BOARD
The Analog Devices (ADI) DVP Eval program and ADV7282-M script files are needed to operate the ADV7282-M evaluation board. The
DVP Eval program and ADV7282-M script files are available on an ADI File Transfer Protocol (FTP) site.
The following setup process is recommended, and is described in detail in Section 2.1 to Section 2.6.
1. Download and install an FTP client.
2. Download the DVP Eval program and ADV7282-M script files from the ADI FTP site.
3. Install the DVP Eval program.
4. Load the ADV7282-M script files.
5. Power up the ADV7282-M evaluation board.
6. Program the ADV7282-M evaluation board.
2.1.DOWNLOAD AND INSTALL AN FTP CLIENT
Download and install an FTP client such as FileZilla in order to access the ADI FTP site.
1. Go to the http://filezilla-project.org/download.php?type=client website.
2. Download the FileZilla FTP client .exe installation file.
3. When the download is completed, run the .exe installation file and follow the onscreen instructions.
2.2.DOWNLOAD ADV7282-M FILES FROM ADI FTP SITE
The DVP Eval program and ADV7282-M script files are available on the ADI FTP site.
1. Open the FTP client, for example, FileZilla.
2. A quick connect bar appears near the top of the FileZilla client window. Enter the following information. (Note that the boxes
are case sensitive.)
a. In the Host box, enter ftp.analog.com.
b. In the Username box, enter adv728x.
c. In the Password box enter1dN62jy.
d. Leave the Port box blank.
3. Press the Quickconnect button.
FileZilla then shows two panes (refer to Figure 2). The left pane displays the Local Site Pane (that is, your computer). The right
pane displays the Remote Site Pane (that is, the ADI FTP site).

ADV7282-M Installation Guide
Rev. A, March 2013 7
Figure 2. Image of ADI ADV7282-M FTP Site
4. On the Local Site Pane, navigate to where you want to drop the ADV7282-M files.
5. On the Remote Site Pane, select the ADV7282-M folder and drag it to the desired location in the Local Site Pane.
The files and folders on the ADI FTP site then copy to your computer.
Note: The Transfer Queue Pane shows the progress of this copying.
6. On the Remote Site Pane, select the Install DVP Eval Latest Source 10-14-11.exe and drag it to the desired location in the Local
Site Pane.
2.3.INSTALL THE DVP EVAL PROGRAM
Note: If the DVP Eval program is already installed on your computer, then this section can be skipped.
1. When the transfer from the FTP site is complete (as described in Section 2.2), double click on the Install DVP Eval Latest
Source 10-14-11.exe file.
2. A window appears showing a software license agreement. After you have read the agreement, press the I Agree button.
3. A new window appears asking if you want to add Desktop and Start Menu shortcuts. Press the Next button.
4. A new window appears (refer to Figure 3), prompting you to select the installation destination folder. Press the Install button.
Note: It is strongly recommended to use the default destination folder. Selecting a different folder can cause the DVP Eval
program to not install correctly in some versions of Windows.
Local Site
Pane (your
computer)
Remote Site Pane
(ADI FTP site)
Enter ADI FTP site details
here. (See Step 2 above.)
Transfer Queue Pane
Shows progress of file transfers from ADI
FTP site to your computer

ADV7282-M Installation Guide
Rev. A, March 2013 8
Figure 3. Installation Destination for DVP Eval Program
5. Restart your computer after the DVP Eval program is installed.
2.4.LOAD THE ADV7282-M SCRIPT FILES
This section describes how to load the ADV7282-M script files to the DVP Eval program.
1. Open the ADV7282-M folder that you downloaded from the ADI FTP site.
2. Open the Software for Rev.A Evaluation Board folder in the ADV7282-M folder.
3. Copy the folder called ADV7282M_CUST to the following directory:
C:\Documents and Settings\USER_NAME\My Documents\Analog Devices\DVP Eval Latest Source 10-14-11\xml\New Boards.
Note: This directory may be slightly different depending on where you installed the DVP Eval program.
4. To open the DVP Eval program, select Start -> Analog Devices -> DVP Eval Latest Source 10-14-11.
5. Select File -> Update Boards.
Figure 4. Update Board Files on DVP Eval Program
A number of black command prompt windows appear and then disappear. Finally, a window appears with the message “update
boards successful”. Press the OK button.
The ADV7282-M script files have been added to the DVP Eval program.
6. Exit the DVP Eval program.

ADV7282-M Installation Guide
Rev. A, March 2013 9
2.5.POWER UP THE ADV7282-M EVALUATION BOARD
1. Connect a mains cable to the 7.5 V supply cable included in the ADV7282-M evaluation kit.
2. Connect the 7.5 V supply cable to Jumper J8 on the ADV7282-M evaluation board. When this is done correctly, LED D6 turns
on (refer to Figure 1).
3. Connect the USB cable included in the ADV7282-M evaluation kit to the computer where you installed the DVP Eval program
and ADV7282-M script files. This cable is used to send commands from your computer to the ADV7282-M evaluation board.
4. Connect the other end of the USB cable to Jumper J7 of the ADV7282-M evaluation board. When this is done correctly, LED D7
turns on (refer to Figure 1).
5. Connect the analog video input(s) to the Ain inputs of the ADV7282-M evaluation board. Refer to Table 1 for information on
how to connect these inputs.
6. Connect SMA cables to the MIPI CSI-2 output connectors and feed these to a sink device.
Notes:
•The I2C lines to the ADV7282-M can be accessed via test points on the evaluation board. Refer to Figure 1.
•Even after the ADV7282-M evaluation board is powered up, the 28.63636 MHz crystal (Y1) will not oscillate until the
ADV7282-M is programmed (refer to Section 2.6).
2.6.PROGRAM THE ADV7282-M EVALUATION BOARD
1. To run the DVP Eval Latest Source application, select Start-> All Programs -> Analog Devices -> DVP Eval Latest Source 10-14-
11.
2. Press the Choose Board button on the top left of the DVP Eval program window and the Board Selector window appears (refer
to Figure 5).
Figure 5. Board Selector Window of DVP Eval Program
3. Select ADV7282M_CUST in the Rx section of the Board Selector window.
4. Select None in the MotherBoard section.
5. Select None in the Tx section.
6. Press the Load button. A window similar to that shown in Figure 6 appears.

ADV7282-M Installation Guide
Rev. A, March 2013 10
Figure 6. DVP Eval Program After Loading ADV7282-M Board
Note: A warning message similar to that shown in Figure 7 appears. This is expected as the I2C slave address of the CSI_Top
map has not yet been programmed. This warning will disappear after any script is run (see step 7).
Figure 7. Warning Message That Appears After Loading ADV7282-M Board
Selects ADV7282-M
Selects Main Map
of ADV7282-M
Selects
Interrupt/VDP Sub
Map of ADV7282-M
Selects
User Sub
Map 2 of
ADV7282-M
ALSB pin of
ADV7282-M tied
high on evaluation
board. Therefore,
I2C device address
of ADV7282-M set to
0x42.
Selects MIPI
CSI-2 Map of
ADV7282-M
Selects Video
Post Processor
Map of
ADV7282-M