Analog way Eikos LE User manual

QUICK START
What’s in the box
Quick install and setup
Thank you for choosing Analog Way and the Eikos LE. By following these simple steps, you will be able to setup
and use your powerful Multi Layer Hi-Res. Mixer Seamless Switcher within minutes. Discover the Eikos LE extensive
capabilities and intuitive interface while conguring your rst show, and unleash your creativity for a new experience in
show and event management by Analog Way.
Eikos LE - EKS400
Key points:
 
 -

 
 
 
        

IN MIXER MODE (Maximum displaying):
1
-2 PIPs
3 PIPs
IN NATIVE MATRIX MODE:
-1 PIP
No preview
Getting started:
 


 

 
 
 

        

         

      


IMPORTANT:       
ENTER

1 x Eikos LE
1 x Power supply cord
2 x DVI male to HD15 female and DVI-D female breakout cable
1 x HD15 to 5 BNC cable
1 x Ethernet cross cable (for device update)
1 x Set of 11 audio 5 pin screw terminals
1 x RCS - Remote Control Software (PC only) *
4 x Screws for handle removal (M4x12mm)
1 x Quick Start guide
1 x User Manual
*Download on our website: www.analogway.com/technical_support/
WARNING !
If required, front handles of the device can be dismantled,
but with caution.
The original screws removed must not be reintroduced to
their location without handles in place.
Substantial damages can occur, including risk of elec-
tric shock from the mains voltage.
Only M4x12mm screws can be used.
(They are supplied with the unit)

Eikos LE - Ref. EKS400
Front Panel Description
OUTPUT #1 to #2: select the output #1 to #2, a layer
and a source, then press TAKE
MATRIX #1 & #2
DVI 1 to DVI 2: Press to access DVI #1 or DVI #2
SDI 1 to SDI 4: Press to access SDI #1 to SDI #4
BLACK: Change the active layer to Black
FREEZE: Freeze the input linked to the current layer on MAIN
Background Frame: Display or change Frame
Background Live/PIP1: Change active Layer
PIP2 to PIP3: Change active layer to a PIP
Logo1 to Logo2: Display or change Logo
PREVIEW: Toggle preview functionality
SHIFT: Secondary function selection button
FUNCTION
Transition the pre-selected sources onto the
MAIN output with the selected effects
EXIT/MENU: Home Menu or back one level
ENTER: Validates the menu or command
STAND-BY: Hold for 3 seconds for stand-by Mode
TAKE
DIGITAL INPUT Selection
LAYER
LAYER SELECTION
CONTROL STAND-BY
Preset section: Stores and recalls 4 presets available
CUT: Select Cut as the current transition type
FADE: Select Fade as the current transition type
USER #1: Select User #1 as a customized transition
USER #2: Select User #2 as a customized transition
P1-4: Select P #1 to #4 as a customized preset
EFFECT / PRESET
OUTPUT SETUP
1-Press the EXIT/MENU button from the Home menu [all functions must be
conrmed by the Enter button]
2-Press [Output]
3-Press [Output format]
4-On Format line, select the display’s native resolution
5-Control or adjust your display device (Monitor or Video Projector)
6-If necessary, select [Test Pattern] in the Output menu
#1-7 L / F #1 to #7: access source #1 to #7, Display Frame or Logo #1 to #7
#8 AL / F #8: access Source #8, Display Frame #8 or Logo #8 or Animated Logo
INPUT SETUP
1-Press the EXIT/MENU button from the Home menu [all functions
must be conrmed by the Enter button]
2-Press [Input] and [Autoset ALL]
3-If the acquisition is successful the source appears on Preview.
Please Toggle the Preview button to display the Mosaic Mode
4-If the acquisition has failed, check all connections and perform a
manual setup
5-For a comprehensive Input Setup, please refer to user’s Manual
6-For a manual input setup, press the EXIT/MENU button:
a) Press [Input],
b) Select the right input from Input #1 up to SDI #4, then
c) Select [Type].
NOTE: To adjust input Size or Pos, use the [Layer] Menus.
To adjust Blanking, use the Auto-Centering or Blanking
adjustments in the Image menu.
BUTTON COLOR USAGE
No light: #1 = Input not available on autolock
#2 = Frame or Logo not available
#3 = Layer not available
#4 = Button not available depending on the user mode
Solid red: #1 = Source, Layer or Window is on Main
#2 = Mosaic Preview enable
#3 = Freeze enable
Solid green: #1 = Source or Layer is on Preview
#2 = Function available for modication
#3 = Current output on Matrix Mode
Dim green: Button available for selection
Blinking red: Active Layer or Source for modication on Main
Blinking green: Active Layer or Source for modication on Preview
Dim red: Stand-by button
Solid orange: #1 = Shift button
#2 = Function available by Shift button
HOW TO USE THE MOSAIC PREVIEW FEATURE
To have a full vision of the aspects of your inputs two modes are available. When
the Mosaic Preview button is activated (Red light solid button):
- One live source mode: select your Layer and the source you want to put on it.
The input selected will be automatically refreshed on your Mosaic Preview
Press a Layer button (Bkgnd Live, PIP1 or 2) --> Press the Live source chosen
- Random live source mode: To have a random refreshment of all your inputs, select
a layer and put it to black. All sources will be automatically refreshed randomly.
Press a Layer button (Bkgnd Live, PIP1 or 2) --> Press the Black Button
ANALOG INPUT Selection

Eikos LE - Ref. EKS400
Rear Panel Description
VIDEO OUT
AUDIO OUTPUT
AUDIO INPUT
RS-232 communication port
on a DB9 female connector or
TCP/IP on RJ45 connector
Power supply: IEC/EN/UL/CSA
60950-1, internal, autoswitchable
Universal Analog Computer/TV/HDTV inputs
SD-SDI/HD-SDI inputs #1 to #4: female BNC
DVI inputs #1 & #2: female DVI-I (digital pins)
Outputs #1 (Main) & #2 (Preview): female
HD15, DVI-I (analog pins)
Connectors:
1x BNC-F: SD/HD-SDI (with audio embedded)
3x BNC-F: Y_Cb_Cr
1x Mini Din 4: S. Video
1x BNC-F: Composite video PAL/NTSC
Balanced or unbalanced mono/
stereo Output
(all Pin MCO mode connector)
IP-LAN connector Balanced or unbalanced mono/stereo inputs
(all pin MCO male connectors)
OPERATIONS OVERVIEW
WORKING IN MIXER MODE
1- Select an input.
2- On the preview screen, the input appears
3- Select an EFFECT (open/close)
4- Press TAKE to view the result on the Main screen
WORKING WITH PIPs IN MIXER MODE
1- Press the PIP2 button. On the preview screen, the PIP (layer) appears as a
color rectangle
2- Select an input. On the preview screen, the input appears in the layer rectangle
3- Adjust the PIP (layer) with ADJUSTMENT button (Pos & Size or Zoom by
Toggle function)
4- Select a transition (open/close) or an effect into Layer menu [Home menu]
5- Press TAKE to view the result on the main screen
6- To remove layer, press BLACK then TAKE
7- For another PIP setup, repeat from step #1
AUDIO CONNECTIONS
MCO male connectors
Inputs #1 to #6: Balanced & unbalanced connection
Inputs DVI #1 to DVI #2: Balanced & unbalanced connection
Input (AUX): Balanced & unbalanced connection
Outputs #1 to #2: Balanced & unbalanced connection
L+
L-
R+
R-
UNBALANCED
LEFT
RIGHT
GROUND
4
4
L+
L-
R+
R-
BALANCED
L+
R+
L-
R-
GROUND(S)
HOME MENU
- MODE : select to choose which mode the Eikos LE will work in (Mixer or Matrix Mode).
- INPUT : select to congure the 12 individual input types and resolutions.
- MAIN OUT : in Mixer mode, select to set the output types and resolutions of the Main output.
- OUTPUT 1 : in Matrix mode, select to set the output types and resolutions of Output 1.
- PREVIEW OUT : in Mixer mode, select to set the output types and resolutions of the Preview output.
- OUTPUT 2 : in Matrix mode, select to set the output types and resolutions of Output 2.
- VIDEO OUT : select to congure Video output card settings.
- PRESET : select to store and use presets.
- IMAGE : select to change source image settings of an input.
- KEYING/TITLING : select to access keying and titling controls and parameters when video layer
is selected.
- LAYER : select to adjust layer size, position, border, transparency or transitions.
- LOGO/FRAME : select to store (record), use and manage logos and frames into the Eikos LE.
- AUDIO : select to access all audio input and output parameters.
- CONTROL : select to access device software information, LAN settings, reset factory settings,
amongst other user oriented functions (see next page).
-VIRTUAL T-Bar : select to access the Virtual T-Bar.

Going further with the EIKOS LE
For complete details and operations procedures, please refer to the Eikos LE User’s Manual and our website for further
information: www.analogway.com.
Version : 3.0 - 29/03/11
Code : 140121
Home Menu (extract)
Warranty
This Analog Way product has a 3 year warranty on parts and labor, return to factory. This warranty does not include faults
resulting from user negligence, special modications, electrical surges, mishandling (drop/crush), and/or any other damage
caused by misuse.
NOTE : The updater les are available on our web site : http://www.analogway.com.
Versions
Key locking
LCD brightness
Key brightness
Prog. Keys
Standby
Erase Memories(L3)
Default values (L3)
Vers.: 3.00 BETA
l3=xxxx l4=xxxx
MM K=xxxx
Remote address (L1)
CA V=xxxx
Device port...
TH V=xxxx
RS232
TCP
Enabled
Netmask...
l1=xxxx l2=xxxx
0=xxxx
Device address...
MF K=xxxx
Gateway address...
FA V=xxxx
Remote port (L1)
CS V=xxxx
LAN
UDP
Input 1 (L4)
DVI 1 (L4)
Input 2 (L4)
DVI 2 (L4)
Input 3 (L4)
SDI 1 (L4)
Input 4 (L4)
SDI 2 (L4)
Input 5 (L4)
SDI 3 (L4)
Input 6 (L4)
SDI 4 (L4)
Input freeze
Baud rate
All
Fade
Set message OFF
Freeze all
Set message ON
Menus
User 1
User 2
Clear message ON
Clear message OFF
Standby
Default setup (L2)
CONTROL
RS232/LAN
LAN setup
Auto Lock
Sync. loss
Auto TAKE
Preset Toggle
V-TBar enable
Freeze mode
Transp Backgr
Dynamic t
(L1) UDP only
(L2) Conrmation asked
(L3) Only for User 1 & User 2
(L4) Visible if Sync. Loss is activated
Direction (L3)
Type (L3)
Effect duration