Andersen 18ST FS User manual

PRODUCT MANUAL
18ST (V.2.0)
18ST FS (V.2.0.F)
RON-WPM-710218-18STFS-Rev.4

EXPLODED VIEW
ITEM. 3
MODEL ST FS - PART No. 537551
ITEM. 3
MODEL ST FS - PART No. 537511
ITEM. 5 - PART No. 786001
p2
18ST (V.2.0)
18ST FS (V.2.0.F)

PARTS LIST
ITEM NO. QTY. DESCRIPTION PART NO.
1 3 Screw 543310
2 1 Self-tailing arm 786105
3 1 Self-tailing top complete
Model ST 537551
3 1 Self-tailing top complete
Model ST FS 537511
3.1 1 Circlip 726400U
3.2 1 Top ring 782100
3.3 6 Screw 781811
3.4 1 Disc - Model ST (537551 only) 726310
4 1 Drum complete 773600
5 1 Drive shaft complete 786010
5.1 1 Drive shaft 786001
6 4 Arm spring 713300
7 4 Pawl 713200
8 1 Bearing 785700
9 1 Bushing (not removable) 716501
10 1 Ratchet gear 785900
11 1 Shaft 785300
12 1 Bushing RD786300
13 1 Gear wheel 786200
14 1 Base 773700
15 1 Bushing for ratchet gear 785500
16 1 Shaft for ratchet gear 785100
1 Service kit 18 (not included) 710018
p3
18ST (V.2.0)
18ST FS (V.2.0.F)

MOUNTING INSTRUCTIONS
PAWL SPRING MOUNTING
Installing the winch is easy, if you follow these instructions. The numbers in ( ) refer to the
position numbers in the parts list.
Tools required for the installation:
• Allenkey(3mm)
• Allenkey(5mm)
• Ø6.5mm.(1/4”)drill
• Beddingcompound
1. Remove screws (1).
2. Remove self-tailing arm (2) and drum (4).
3. PlacethetemplateanddrillholesØ6.5mm(1/4”).
Makesurethatnodustcomesintocontactwiththewinchwhiledrilling.
4. Apply a light coat of bedding compound, ensuring that each bolt hole is bedded.
Keep drain grooves clear.
5. Fastenbase(14)intoplaceusing6pieces.M6(1/4”)countersunkheadscrews.
Uselargewashersorabackingplate.
6. Assemble in reverse order.
7. Checkthatthewinchisfunctioningcorrectly:
-Thedrumshouldoperatesmoothly,byturningthedrumclockwisebyhand.
-Thedrummustnotturnwhentryingtoturnthedrumanticlockwise.
-Whileturningthewinchhandleclockwisethedrumshouldturn.
-Whileturningthewinchhandleanticlockwisethedrumshouldnotturn.
• 6xM6(1/4”)countersunkheadscrewsandcorresponding
nuts(lengthdependingondeckthickness).
• 6xlargewashersorbackingplate
• Ringspannertomatchnuts
Note the curved
spring“arm”
p4
18ST (V.2.0)
18ST FS (V.2.0.F)

SERVICE INSTRUCTIONS
• Allenkey(3mm)
• ANDERSENwinchgrease
Tools required for service:
• Screwdriver(large)
• Screwdriver(small)
• Winchhandle
1. Remove screws (1).
2. Remove self-tailing arm (2).
3. Remove drum (4).
4. Pull up the drive shaft (5) gently, using the winch handle.
5. Remove pawls (7) and springs (6).
6. Remove shaft (11) and pull out gearwheel (13).
7. Lift up ratchet gear (10) and pull it out through hole in base (14).
8. Cleanallpartsinwhitespirits/mineralspiritsincludinggearteeth.
9. Assemble in reverse order. During assemble, by the use of a small soft brush lightly grease
all gear teeth, drive shaft, roller bearing, shafts, pawls, springs and bushings. Pawls should
only be lubricated with a very thin film of ANDERSEN WINCH GREASE. It is very important
that pawls can move freely.
IMPORTANT: Whenassemblingthewinch,checkthefunctioningofeachpawlbypushing
the pawl against the spring. The pawls should move smoothly and automatically return to
their normal position, where the pawls engage with the teeth. If the pawls do not function
correctly,cleanandlubricatethepawlsandgears.Checkthefunctionofthepawlsagainto
makesurethatitworkscorrectly.Ifthepawlsdonotworkcorrectlyreplacethespringsand
recheckthefunctioning.
Malfunctioningpawlsmayleadtounexpectedreleaseofthewinchforceresultinginfatal
injuries to the user and others.
ServiceKitNo:18(part.no.710018)containssparepartsforthesewinches.
Maintenance instructions for PVD coated stainless steel surfaces.
PVD-coated surfaces should be rinsed regularly in fresh water to remove any salt residue, dirt
orothercontaminantsanddriedgentlywithasoftcloth.Toremovegreaseorothermarks,a
mild abrasive free cleaning agent such as spray-on glass cleaning solution may be used. No
caustic detergents or other aggressive or abrasive cleaning agents should ever be used, as
they may damage the surface.
p5
18ST (V.2.0)
18ST FS (V.2.0.F)

GENERAL INFORMATION
Due to the best choice of materials and high precision in manufacturing, we recommend, for
normal use, only to dismantle, clean and lubricate the winch once every second year. Under
extensiveuse,suchasracing,charterorbluewatersailing,werecommendtolubricatethe
winch once every year.
We strongly recommend always to use ANDERSEN WINCH GREASE, when lubricating your
winch.ANDERSENWINCHGREASEisahighqualitysilicone/Teongreaseproduct.
Mostothertypesofgrease,including“marinegrease”arenotsuitableforlubricationof
winches. Non-suitable grease products can cause malfunction, which could result in fatal
injuries for the user and others.
Pawl arm springs should be replaced every second year. Spare arm springs and other parts
that may be required are included in the ANDERSEN Service Kit. Please refer to the service
instruction for the Service Kit suitable for the specific winch.
When the winch handle is not in use but the winch is under load, we recommend, from a
safety point of view, to remove the winch handle from the winch.
To ensure correct function of the self-tailing unit, only use recommended line sizes. When
using the winch with mooring lines DO NOT use the self-tailing function and be sure that the
mooring line is not in contact with the self-tailing arm.
To ensure the best possible functioning of the winch, we recommend that
the winch is placed in accordance with the line entry (shown below).
Be also aware that the self-tailing arm is positioned correctly. We recommend to have the
self-tailing arm positioned within the shaded area (shown above). On this model the self-
tailing arm can be placed in several dierent positions after having installed the winch.
To identify the Output Drive Gear, insert a winch handle into the winch
androtateinbothdirections,thedrivegearwillonlyrotateclockwise
in a fast and slow speed.
Ideal
rope
entry
Output
drive
gear
p6
18ST (V.2.0)
18ST FS (V.2.0.F)

SAFETY NOTICES
ALL WINCHES
DO NOT DISCARD
Failure to observe these precautions
could result in serious injury or death.
Read All Safety Notices and Product Manuals
Do not install or operate this winch before reading and fully understanding the contents of
this Product Manual.
Stay Alert When Operating
Andersen winches are very powerful and have the potential to cause significant damage
and/orseriousinjuryifusedimproperlyorwithoutduecautionandvigilance.
Operators Must be Trained
Helppreventsignicantdamageand/orseriousinjurybyensuringanypersonoperatinga
winch has a thorough understanding of its proper operation and is aware of the potential
hazards involved. As a minimum, all winch operators must read and understand this Safety
Notice Sheet and the Product Manual.
Particularattentionisdrawntothefollowingpoints:
• Childrenandothersnotqualiedtooperateanelectricwinchmustbekeptatasafe
distance from the winch and any rigging or fittings that are under load.
• Longhairand/orlooseclothingmustbetiedbacktoavoidbeingcaughtinthewinch.
• In the event of a rope override or other fault, stop the winch and turn o power before
attempting to resolve the problem.
Avoid Accidental Operation
Remove winch handles and turn o power to the winch when not in use to help avoid
unsupervised or unintentional operation. Failure to do so could result in significant
damageand/orseriousinjury.
Maintenance
Turnopowertothewinchbeforeperforminganymaintenanceorservicetasks.Failure
todosocouldresultinsignicantdamageand/orseriousinjury.
Lifting Operations
Thewinchmustnotbeoperatedwiththeropeintheselftailerwhenusedinanykindof
lifting operation.
Any lifting operations should be conducted by two persons in order to maintain constant
visual contact with the object being lifted.
Furthermore the self tailer must not be used as a cleat for a rope used to lift or suspend
any object. The rope must be secured properly by tying o, or leading to a suitable fitting
such as a cleat or bollard.
p7
18ST (V.2.0)
18ST FS (V.2.0.F)

Visit www.andersenwinches.com
Visitwww.ronstan.com/warranty
Manufactured by Ronstan Denmark ApS.
Jægervænget36-7100Vejle-Denmark
o[email protected]-www.andersenwinches.com
WORLDWIDE DISTRIBUTION & SERVICE
WARRANTY
18ST (V.2.0) |18ST FS (V.2.0.F)
p8
PRODUCT MANUAL