Andersen 58/62 STE SE User manual

www.Busse-Yachtshop.de - [email protected]
Manual
58/62 & 68/72 STE SE
2+1 SPEED
12V & 24V
GENEREL INFORMATION
MOUNTING INSTRUCTION
EXPLODED VIEW
PARTS LIST
CONNECTING DIAGRAM
WIRE DIMENSION AND FUSE SIZE
WORLD WIDE DISTRIBUTION LIST
SERIAL NO: PS_____________

www.Busse-Yachtshop.de - [email protected]
CONGRATULATIONS
You have purchased an ANDERSEN high quality winch. This product is a result of many years of
development and experience in producing winches for sailboats. This winch gives you a high degree of
functionality and many years of safe and easy sail handling.
GENERAL INFORMATION
PLEASE READ THIS BEFORE INSTALLING YOUR ANDERSEN ELECTRIC WINCH.
The electric ANDERSEN winch has some built-in advantages:
-Easy to fit on your boat.
-Template included.
-Special tools included.
-Electric unit is turnable in 8 horizontable steps (45°).
-Easy to dismantle. Winch and electric unit can be dismantled separately.
-Winch in the usual high ANDERSEN quality, featuring drum, roller bearings etc. of stainless
steel.
-Always the possibility of manual (2 speed) drive, just by inserting a standard winch handle.
No shift-bottom of any kind.
-MODULAR POWER SYSTEM©: Always the possibility of changing to a hydraulic drive unit
or from 2+1 SE to a 2+2 or the Compact© electric drive unit.
Mounting installation:
Follow mounting instructions on next page:
Ensure that each hole in the deck is bedded, including the big hole in the center.
IMPORTANT: Be careful not to put bedding compound IN the thread holes in the deck plate.
Ensure that the sealing ring (O-ring) on top of the gear unit is placed in its groove.
Electric Installation:
Follow mounting instructions on next page and Wire dimensions & fuse sizes on last page.
WARNING: Do not use smaller wire, than recommended in the diagram. This can cause malfunction of
the winch and in worst case; FIRE. The wires should always be as short as possible.
Normal Use:
The electric motor has built-in overload circuit breaker, which breaks the circuit, before the motor gets
too hot.
After a short period of cooling, depending on temperature under deck, ventilation etc., the winch will be
ready for electrical operation again.
Meanwhile, if necessary, just insert a standard winch handle, and use the winch as a 2 speed manual
winch. We recommend to remove the handle when operated electrically - from a safety point of view.
General Service Instructions:
The electric drive unit is lubricated & sealed and requires no further maintenance.
The part on deck is a standard self tailing winch, and needs regular service. We recommend
dismantling, cleaning and lubrication once a year. Under extensive use, such as racing, charter or blue
water sailing, we recommend to make a further lubrication check during the one year period.
We strongly recommend always to use ANDERSEN WINCH GREASE© when lubricating your winch.
ANDERSEN WINCH GREASE© is a high quality silicone/Teflon® grease.

www.Busse-Yachtshop.de - [email protected]
MOUNTING INSTRUCTION
58/62 & 68/72 STE SE
2+1 SPEED
FIG.1
FIG.2
FIG.4
FIG.3
Ø24

www.Busse-Yachtshop.de - [email protected]
Important Installation Information!
It is extremely important that your motor is aligned with your winch. Non-aligned motors will be noisy
and gear wear will be accelerated.
To insure that your motor is aligned properly the motor flange must be flush with the deck plate and the
eight-sided nut must fit snugly into the octagon in the deck plate.
This can be achieved with the help of the following:
•Drill the hole through the deck wider that the motor flange. When mounted there must be free
space between the deck and the flange.
•Clean the deck hole before attempting the install the motor so that the motor flange does not
catch splinters of fiberglass or wood when being inserted through the deck.
•Insure that the underside of the deck plate is clean and free from resin, varnish or sealants.
•Do not use a sealant between the flange and deck plate. An o-ring insures a waterproof
connection. Extra waterproofing can be achieved by applying sealant to the top of the deck
plate next to the mounting nut after installation.
•Insure that the locking screw on the mounting nut is not protruding beyond the contact surface
before tightening the mounting nut. Tighten the locking screw when the mounting nut is
securely in place.
Deck plate
Motor
flange Deck
Mounting
nut
Locking
screw
The motor
flange must sit
flush with the
deck plate here.
Deck hole larger
than flange

www.Busse-Yachtshop.de - [email protected]
EXPLODED VIEW
58/62 & 68/72 STE SE
2+1 SPEED
2.2
4
5
6
3
2.2
2.14
2.13
2.1
2.4
2.5
2.7
2.6
2.12
2.11
2.1.2
2.1.1
2.10
2.3
2.8
7
8
9
10
12
13
14
17
11
ACCESSORIES
15 16
1
2
2.9

www.Busse-Yachtshop.de - [email protected]
PARTS LIST
58/62 & 68/72 STE SE
2+1 SPEED
POS. QTY. DESCRIPTION ART. NO.
1 EL-unit 58/62STE TYPE SE 12V 777100
EL-unit 58/62STE TYPE SE 24V 777110
EL-unit 68/72STE TYPE SE 12V 777120
EL-unit 68/72STE TYPE SE 24V 777130
1. 1 Motor CIMA 1500W 12V STE SE 777340
1. 1 Motor CIMA 1500W 24V STE SE 777350
1.1 1 Key DIN6885-A-5X5X15
2.0 1 Gear unit 58-72STE SE 776150
2.1 1 Gear i38 VF63SE 776230
2.1.1 8 Washer DIN125-A4-Ø6
2.1.2 4 Screw DIN912-A4-M6x25
2.2 2 Key DIN6885-A-8X7X20
2.3 1 Ratchet gear 775860
2.4 1 Washer 835000
2.5 1 Bushing RD100439
2.6 2 Pawl 713200
2.7 2 Pawl spring 713300
2.8 1 Drive shaft 837000
2.9 1 Washer 775890
2.10 1 Drive shaft housing 775850
2.11 1 Bushing 823100
2.12 1 Sealing ring RD100169
2.13 1 Gear wheel 980900
2.14 1 Circlip RD829680
3. 1 O-ring RD100074
4. 3 Pin 713401
5. 1 Deck plate 58/62 STE 747700
5. 1 Deck plate 68/72 STE 740200
6. 6 Screw 580100
7. 1 Centre nut 584502
8. 1 Screw DIN916-A4-M5x8
9. 1 Pin spanner RD738000
10. 1 Allen key 593000
11. 1 Allen key 592900
12. 1 Template 58/62STE RD100214
12. 1 Template 68/72STE RD100215
13. 1 Switch labels RD100029
14. 1 Switch RD581900
15. 1 Sealing 735050
16. 3 Screw RD100025
17. 1 Control box 12V 990212
17. 1 Control box 24V 990224

www.Busse-Yachtshop.de - [email protected]

www.Busse-Yachtshop.de - [email protected]
CONNECTING DIAGRAM
12V + 24V
58/62 & 68/72 STE SE
2+1 SPEED

www.Busse-Yachtshop.de - [email protected]
FUSE
-+
BATTERI
MINIMUM WIRE DIMENSIONS & FUSE SIZES
(Not for continuous service)
IMPORTANT: Do not use connection 1D1
REMARK: Fuse must be of a slow blow type

www.Busse-Yachtshop.de - [email protected]
WINCH WIRE LENGTH* 12V. DC 24V. DC
WIRE FUSE BAT.
CAP. WIRE FUSE BAT. CAP.
58/62 STE SE 0-3 m / 0-10 ft 70 mm² 200 A 360 Ah 35mm² 125 A 240Ah
3-8 m / 10-27 ft 95 mm² 224 A 360 Ah 50mm² 200 A 240Ah
68/72 STE SE 0-3 m / 0-10 ft 70 mm² 200 A 360 Ah 35mm² 125A 240Ah
3-8 m / 10-27 ft 95 mm² 224 A 360 Ah 50mm² 200 A 240Ah
*) WIRE LENGTH is defined as the distance from battery to switch box + the distance from switch box
to motor.
IMPORTANT: Fuse must be of a slow blow type.
For current World Wide Distributor list please see:
www.andersenwinches.com