Anilam 6000 User manual

6000 CNC CONTROL
Simple Program

1.
CREATING A PROGRAM
From Manual page press F2 PROGRAM
CREATE
F2
Press
The softkeys will changed as shown below.
Type the program name (Maximum 8 letters/numbers).
Press Enter put into program directory

2.
EDIT
High light will be on program just created.
Press F8

3.
This is how screen will appear when entering EDIT
Program name
Note:Softkeys have change .
Note:Insert is turn ON ,if not will not go past bottom of page.

4.
X0 Y0
.75
2.75
.5
1.5
This part needs to have 4 hole drilled .25 dia and .5 deep

5.
Press HELP
High light will be on G0 press enter
Move high light G17 , G70 and G90 press enter on each of these.
F1
Press M5 press
Exit
Press it will go into program as shown below.
F10

6.
Top line of program.
Program has been edited
Cursor position line and column
Lines 2 and 3 are typed in manually.
The * allows commence into program control will read
ignore after it.

7.
Screen will appear as shown below.
Press #2 for basic drilling, press enter.
Press press #9 for DRILL press
HELP
F1

8.
Enter values Finish Depth -.5 press down arrow, enter
Start Hgt .1 down arrow and Feedrate 12
The next enter hole positions.
Type G0 X.75 Y.5 X2.75 Y1.5 X.75
Type G80
Cancel drill, this must always in program after last hole.
Exit
Press exits help menu and enters line into program.
F10

9.
Press press
Exit Draw
View XY plane
View XZ plane
View YZ plane
View isometric
Fit to screen
Zoom window
Half current size
Double current size
Scale drawing
Pans part around screen
Erase screen
Displays text ----------------
Displays tool-----------------
Show tool comp-------------
Rapid ON/OFF--------------
Displays axis----------------
Grid ON/OFF----------------
Size of grid-------------------
Auto/single step/motion---
Run ON/OFF----------------
Erase screen----------------
Block to start draw---------
Block to end draw----------
Edit program
Run program
Exit draw mold
F10 F7
Soft key will change as shown below.
Type in last three lines.

10.
Press cursor will be on FIT press enter
DISPLAY
This will fits drawing to screen.
Red lines are RAPID moves , blue circle are the holes and
purple circle is the tool.
Press this brings control back to program page
Press to select program ,check that high light is
on correct program.
Press go to Manual
Select
Exit
F5
Exit
F10
F6
F10

12.
SETTING PART ZERO.
If using an edge finder , touch edge of part using jog keys.
Go to tool page press press
Tool OFFSETS
Press this will enter value into table.
CalibX
Cursor to required OFFSET using arrow up and down keys.
Move X axis until part is located with edge finder.
Because the edge find is .2 dia the position will be incorrect , press
the letter A key ,a box as shown below will appear.
Type in X.1 this will adjust offset to correct position press ENTER.
Repeat for Y axis
All offset are taken from machine Home position.
F9 F1
F4

13.
SETTING TOOL LENGTH OFFSETS
Put tool in spindle , bring tool tool down to top of part.
Press high light correct tool number in tool page
press
If there are more move Z axis up change to next tool
and calibrate it as before,tool #0 must always be active
when setting offsets.
Press when all tools are calibrated.
Tool
CalibZ
Exit
F9
F8
F10
RUNNING PART.
Press turn down feedrate override knob to 10%
Auto
If machine has a tool changer ,it will put tool #1in spindle if
not already there.
If no tool changer install it will stop and allow you to change
tool if necessary .
When program complete Zaxis will go up to 5” above part.
Press
% FEED
F6