anko SLR-23050 User manual

a
c
e
b
f
g
d
a. 10 inches ring light
b. 360° ball head mounting bracket
c. Tripod stand
d. Bluetooth Selfie remote control
e. Reflection screen
f. Phone clip set to assemble on the ring
g. Phone clip set to assemble on the tube
SPECIFICATION:
• USB input: 5V DC 2A
• LED wattage: Max. 10W
INSTRUCTIONS FOR ASSEMBLY:
1. Take out the components from assembling pack.
2. First, take out the tripod stand. Loosen the third screw knob. Pull out the tripod stand. Adjust height to make the adjustable bracket
at the horizontal position. It is the most stable position when the adjustable bracket at the horizontal position. Tighten the screw
knob.
3. Loosen the first and second screw knobs to adjust the height you need.
4. Install the 360° ball head mounting bracket to the tripod stand.
5. Install the phone clip to the electrical ring. Please pay attention to the width scope of the clip.
6. Install the electrical ring with phone clip to the 360° ball head mounting bracket. You can loosen the screw knob on the 360° ball
head mounting bracket to adjust the angle of the ring.
7. There is other phone clip which can be assembled on the tube if you want. Loosen the screw knob, open the tube clip, install it to
the tube where you would like to place. Close the tube clip and tighten the screw knob to fix.
10" RING LIGHT
K: 43351640 T: 68734992
SLR-23050
IMPORTANT SAFETY INSTRUCTIONS:
The following safety precautions should always be followed, to reduce the risk of electric shock, personal injury
or fire. It is important to read all of these instructions carefully before using the product, and to save them for
future reference or new users.
THE PACK INCLUDES`:
1. This product must only be used as intended in accordance with the enclosed operating instructions.
2. If the external flexible cable or cord of this luminaire is damaged, this product should be discarded
3. If the luminaire stops unexpectedly or appears to malfunction, switch off the power supply and stop using immediately.
Seek professional advice to rectify the fault or make repairs.
4. Switch off the power supply when not in use, before cleaning or changing accessories.
5. Keep the luminaire and cable away from sources of heat, sharp objects or anything that may cause damage.
6. Be aware that some surfaces may become hot. Do not touch hot surfaces and supervise others accordingly.
7. This product has not been designed for use by children. Children should be closely supervised at all times when they
are near any electrical appliance.
8. To protect against electric shock, never allow the luminaire come into contact with water or any other liquid.
9. Never reach this luminaire that has fallen into water. Do not re-use until the product has been inspected and approved
by a qualified electrician.
10. Do not use outdoors. This luminaire has been designed for domestic indoor use only.
11. Use only a microfiber and dry cloth for cleaning the product.
12. Operate carefully to not cause any damage by dropping or physical shocking it.
13. Do not leave the product in excessive heat, high temperatures can cause the product to malfunction.
14. The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire
shall be replaced.
15. Not suitable for mounting on tubular material.

1. Take out the components from assembling pack. Remove the cap on the top before assembing. Loosen the third screw
knob. Pull out the tripod stand. Adjust height to make the adjustable bracket at the horizontal position. It is the most stable
position when the adjustable bracket at the horizontal position. Tighten the screw knob. Then loosen the first and second
screw knobs to adjust the height you need. Then tighten the screw knobs to fix the height.
2. Install the 360° ball head mounting bracket to the tripod stand. Install the electrical ring light to the 360° ball head
mounting bracket. You can loosen the screw knob on the 360° ball head mounting bracket to adjust the angle of the ring.
Remove the cap before assembling
The second screw knob
The first screw knob
The third screw knob
360° ball head mounting bracket
Adjustable bracket to be horizontal position
Assemble the phone clip set
before installing to the ring.
Assemble the phone clip set
before installing to the tube.

BLUETOOTH SELFIE REMOTE CONTROL WARNING
1. Do not dispose of unit in fire or water
2. Never attempt to disassemble and reassemble.
3. Waste electrical products should not be disposed of
with household waste, please recycle where facilities
exist.
4. Check with your local guthority for recucleadvice.
5. Keep your device and all accessories out of the reach
of children and animals.
6. Small parts may cause choking or seriousinjury if
swallowed.
7. Avoid exposing your device to very cold or very hot
temperatures (below 0℃or above 45℃).
8. Extreme temperature can cause deforming of the
device and reduce the charging capacity and life of your
device.
9. Do not allow your device to get wet-liquids can cause
serious damage.
10. Do not handle your device with wet hands.
WARNING: OPEN THE REFLECTION SCREEN CAREFULLY. THERE IS STRONG ELASTIC
FORCE DURING OPENING THE REFLECTION SCREEN. IT MAY HIT YOUR BODY.
Short video page up
Short video page down
Bluetooth ON / OFF key
E-book page downE-book page up
Bluetooth connection
indicate light
Camera button
Bluetooth selfie remote control
COMPONENTS USING INSTRUCTIONS:
Inline switch
ON / OFF
Brightness reduce
Brightness increase
Mode changing
60cm
• Please install 2 x 1.5V AAA batteries in Bluetooth selfie remote
control before use.
• Push the ON/OFF key to ON, LED light will flash blue when
ready to pair to your mobile.
• In the Bluetooth menu on your mobile phone, search for “anko
43351640” and connect.
• Indicator light will turn off after connected successfully.
• Press camera button to take selfie
Note: The indicator light will turn off and remote control will
enter sleep mode. Press any button to re-activate the remote.
Pause for short video

Unfold and fold instructions： Unfold instructions： Fold instructions：