Anolis ArcWash Recessed 136 RGB User manual

Version 1.0

3

3
Table of contents
1. Safety i 4
2. Op 4
3. Desc 5
4. Installation.. 6
4.1 Mounting the xture..................................................................................................................6
4.2 Fitting the frost ltr...................................................................................................................7
4.3 DMX-512 connection/connection between xtures................................................................. 8
5. ArcWash Recessed 136 RGB - DMX protocol,version 1.0...................................................... 9
6. ArcWash Recessed 136 RGB - Control menu map............................................................... 11
7 12
7.1 Fixture 
7.2 Fixtur
7.3 Personality.
7.4 Manual mo
7.5 Test seq
7.6 Reset func
7.7 Special 
8. Pow 16
9. Error and information messages............................................................................................ 16
10. Technical specications........................................................................................................ 17
1 19
12. Ceiling boxes - versions and dimensions............................................................................ 20
ArcWash
Recessed 136 RGB

4
5
CAUTION! Keep this device away from rain and moisture!
Unplug mains lead before opening the housing!
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE YOU INITIAL START - UP!
1. Safety instructions
Every person involved with installation and maintenance of this device have to:
- be qualied
- follow the instructions of this manual
CAUTION! Be careful with your operations. With a high voltage you can suffer
a dangerous electric shock when touching the wires!
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure a safe ope-
ration, it is absolutely necessary for the user to follow the safety instructions and warning notes written in this manual.
Important:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any
unauthorized modication to the device.
Please consider that damages caused by manual modications to the device are not subject to warranty.
Make sure that the available voltage is not higher than stated on the rear panel.
f the device has been exposed to drastic temperature uctuation (e.g. after transportation), do not switch it on immedia-
tely. The arising condensation water might damage your device. Leave the device switched off until it has reached room
temperature.
Always disconnect from the mains, when the device is not in use or before cleaning it.
This device falls under protection class I. Therefore it is essential to connect the yellow/green conductor to earth.
The electric connection, repairs and servicing must be carried out by a qualied employee.
Do not connect this device to a dimmer pack.
During the initial start-up some smoke or smell may arise. This is a normal process and does not necessarily mean that
the device is defective.
Do not touch the device’s housing bare hands during its operation (housing becomes hot)!
CAUTION ! EYEDAMAGES !
Avoid looking directly into the light source (meant especially for epileptics) !
2. Operating determinations
This device is a moving-head spot for creating decorative effects and was designed for indoor use only.
Do not shake the device. Avoid brute force when installing or operating the device.
Never lift the xture by holding it at the projector-head, as the mechanics may be damaged. Always hold the xture at the
transport handles.
When choosing the installation-spot, please make sure that the device is not exposed to extreme heat, moisture or
dust.
The minimum distance between light-output and the illuminated surface must be more than 0.8 meter.
Make sure that the area below the installation place is blocked when rigging, derigging or servicing the xture.

4
5
Only operate the xture after having checked that the housing is rmly closed and all screws are tightly fastened.
The maximum ambient temperature 40° C must never be exceeded.
Operate the device only after having familiarized with its functions. Do not permit operation by persons not qualied for
operating the device. Most damages are the result of unprofessional operation!
Please use the original packaging if the device is to be transported.
Please consider that unauthorized modications on the device are forbidden due to safety reasons!
DANGER TO LIFE!
For protection from dangerous electric shock,the xture must be
installed in ceiling box and covered with box covers before applying power!
3. Description of the device
1 - Ceiling box
2,3 - Box covers
4 - Arm
5 - Front glass
6 - Moving head
Control panel
13 - Display
14 - Mode-button
15 - Enter-button
16 - Up-button
17 - Down-button
Moving head´s base
7 - Control panel
8 - DMX output
9 - DMX input
10 - Fuse holder
11 - Power terminals
12 - Moving head base
1 - Ceiling box

6
7
4. Installation
4.1 Mounting the xture
The moving head is designed for ceiling mounting.
The installation is of the projector has to be built and constructed in a way that it can hold 10 times the weight for 1 hour
without any harming deformation.
When rigging, derigging or servicing the xture staying in the area below the installation place, under high working places
and other endangered areas is forbidden.
The operator has to make sure that safety-relating and machine-technical installations are approved by an expert before
taking into operation for the rst time and after changes before taking into operation another time.
The operator has to make sure that safety-relating and machine-technical installations are approved by an expert after
every four year in the course of an acceptance test.
The operator has to make sure that safety relating and machine-technical installations are approved by a skilled person
once a year.
The moving head should be installed outside areas where persons may walk by or be seated.
IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including calculating working load limits,
installation material being used, and periodic safety inspection of all installation material and the projector. If you lack these
qualications, do not attempt the installation yourself.Improper installation can result in bodily injury and (or) damage to
property.
The moving head should be installed out of the reach of people.
Danger of re !
When installing the device, make sure there is no highly inammable
material (decoration articles, etc.) in between a distance of min. 0.5 m.
CAUTION!
Make sure that the device is xed properly! Ensure that the structure (truss)
to which you are attaching the xtures is secure.
The ArcWash Recessed 136 RGB includes a moving head and a ceiling box for mounting to the lower ceiling.
Installation:
1.Fix the recessed ceiling box (8) to the lower ceiling.Be careful the mounting grid can hold the moving head installati-
on!
The ceiling box must be xed properly ,otherwise the vibration of the mounting structure can occur during the operation of
the moving head. Pull the power cable (5) and data cables through the apertures (1) on the bottom of the box.
2.Put the moving head base (4) on the 4 xative pins (6) in the bottom of the ceiling box (8) and turn the base gently to
the right. Insert and tighten clockwise the 2 quick-lock fasteners (7) to secure the moving head in the ceiling box.

6
7
3.Use the 3-wired power cable (the wires with cross-sectional area of 1.5mm2 ) to connect the power.
Pull the power cable through a cable holder (3) and connect it into the connection terminals (2) as follows:
Possible pin identication schemes:
Cable (EU) Cable (US) Pin International
Brown Black Live L
Liht blue White Neutral N
Yellow/
Green Green Earth
Connect the earth-wire (10) with the earth-terminal (9) on the ceiling box (8).
If you have any doubts about proper installation,consult a qualied electrician!
Make sure the wires are securely connected.Tighten 2 screws in the cable holder to secure the power cable in it.
For protection from electric shock,the xture must be grounded!
4.Connect the data cables to the xture DMX input/output.
5.Fasten 2 covers on the ceiling box by 14 screws.
DANGER TO LIFE!
For protection from dangerous electric shock,the xture must be
installed in ceiling box and covered with box covers before applying power!
Before taking into operation for the rst time,the installation has to be
approved by an expert!
When installing xtures side-by-side,
avoid illuminating one xture with another!
4.2 Fitting the frost ltr
The ArcWash Recessed 136 RGB is supplied with clear front glass (factory tted) and two types of frost lters (lms). If
you wish to use a diffusive light ,follow the steps to install desired frost lter:
1
2
2.Put the frost lm on the front glass and centre the holes
in the lm on the holes in the holder of the glass.
3.Put the ring carefully back and tighten both fastening
screws.
1.Remove the ring (1) from the forefront
of the head by loosening both fastening
screws (2).
3

8
9
4.3 DMX-512 connection/connection between xtures
The xture is equipped with 3-pin XLR sockets for DMX input and output. Only use a shielded twisted-pair cable designed
for RS-485 and 3-pin XLR-plugs and connectors in order to connect the controller with the xture or one xture with
another.
Occupation of the XLR-connection:
DMX - output DMX-input
XLR mounting-sockets (rear view): XLR mounting-plugs (rear view):
Building a serial DMX-chain:
If you are using the standard DMX-controllers, you can connect the DMX-output of the controller directly with the DMX-
-input of the rst xture in the DMX-chain. If you wish to connect DMX-controllers with other XLR-outputs, you need to
use adapter-cables.
Connect the DMX-output of the rst xture in the DMX-chain with the DMX-input of the next xture. Always connect output
with the input of the next xture until all xtures are connected.
Caution: At the last xture, the DMX-cable has to be terminated with a terminator. Solder a 120 Ohm resistor between
Signal (–) and Signal (+) into a 3-pin XLR-plug and plug it in the DMX-output of the last xture.
Building a master/slave-chain:
Connect the DMX-output of the master xture in the data-chain with the DMX-input of the rst slave. Always connect output
with the input of the next slave until all slaves are connected (up to 32 xtures).
Caution: It’s necessary to insert the XLR termination plug (with 120 Ohm) into the input of the master xture and into the
output of the last slave xture in the link in order to ensure the proper transmission on the data link.
1 - Shield
2 - Signal (-)
3 - Signal (+)
Master/slave operation
DMX operation

8
9
5. ArcWash Recessed 136 RGB - DMX protocol,version 1.0
Mode 1
Channel
Mode 2
Channel Value Function Type of control
1 1 0 - 255 Pan
Pan movement by 530° proportional
20 - 255 Pan Fine
Fine control of pan movement proportional
3 2 0 - 255 Tilt
Tilt movement by 280° proportional
40 - 255 Tilt ne
Fine control of tilt movement proportional
5 3
0
1 - 255
1 - 255
Pan/Tilt speed, Pan/Tilt time
Max. speed (tracking mode)
P./T. speed-set Speed Mode in menu: P./T. Mode
Speed from max. to min. (vector mode)
P./T. time - set Time Mode in menu: Pan/Tilt Mode
Time from 0.1 s to 25.5 s.
step
proportional
proportional
6
0 - 9
10 - 31
32 - 63
64 - 95
96 - 127
128 - 159
160 - 191
192 - 223
224 - 255
Pan/Tilt macro selection
Disabled pan/tilt macro
Reserved
Figure of circle (from small to large)
Figure of horizontal eight (from small to large)
Figure of vertical eight (from small to large)
Figure of rectangle (from small to large)
Figure of triangle (from small to large)
Figure of ve-pointed star (from small to large)
Figure of cross (from small to large)
step
step
proportional
proportional
proportional
proportional
proportional
proportional
proportional
7 0
1-127
128-129
130-255
Pan/Tilt macro speed
Set pan/tilt speed (channel 5) at 0 DMX
No macro generation
Macro generation from fast to slow-forwards
No macro generation
Macro generation from slow to fast-backwards
step
proportional
step
proportional
80 - 129
130 - 139
140 - 255
Special functions
Reserved
Pan/tilt reset
Reserved
step
9 4 0-255
Red LED
Red LED saturation control (0-100%) proportional
10 5 0-255
Green LED
Green LED saturation control (0-100%) proportional
11 6 0-255
Blue LED
Blue LED saturation control (0-100%) proportional
12
0-7
8-15
16-23
24-31
32-39
40-47
48-55
56-63
64-71
72-79
80-87
88-95
96-103
104-111
112-119
120-127
128-135
Colour MACRO SELECTION
No function
Macro 1
Macro 2
Macro 3
Macro 4
Macro 5
Macro 6
Macro 7
Macro 8
Macro 9
Macro 10
Macro 11
Macro 12
Macro 13
Macro 14
Macro 15
Macro 16
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step

10
11
Mode 1
Channel
Mode 2
Channel Value Function Type of control
12
136-143
142-151
152-159
160-167
168-175
176-183
184-191
192-199
200-207
208-215
216-223
224-231
232-239
240-247
248-255
Macro 17
Macro 18
Macro 19
Macro 20
Macro 21
Macro 22
Macro 23
Macro 24
Macro 25
Macro 26
Macro 27
Macro 28
Macro 29
Macro 30
Macro 31-Rainbow effect
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
13 7
0-31
32-63
64-95
96-127
128-143
144-159
160-191
192-223
224-255
SHUTTER/STROBE
Shutter closed
Shutter open
Strobe-effect from slow to fast
Shutter open
Opening pulses in sequences slow--> fast
Closing pulses in sequences fast --> slow
Shutter open
Random strobe-effects from slow to fast
Shutter open
step
step
proportional
step
proportional
proportional
step
proportional
step
14 8 0-255
DIMMER
Dimmer intensity from 0% to 100% proportional

10
11
6. ArcWash Recessed 136 RGB - Control menu map
Default settings=Bold print
A001 (001-498)
InFo
tEMP.
VErS.
IC1.b.
IC2.b.
PErS.
r.PAn (On,Off)
r.tilt (On,Off)
MI.SE (1...10...20)
dM.Pr. (Mod.1,Mod 2)
FEEd. (On,Off)
P.t.Mo. (SP.Mo.,ti.Mo.)
bL.Co.(On,Off)
bl.P.t. (On,Off)
BALA. (On,Off)
C.bAL.
rEd.b. (0..200..255)
GrE.b. (0...255)
bLu.b. (0..215..255)
I.bli. (On,Off)
dFSE
MAn.C.
Pan (0-255)
:
dimr (0-255)
tESt
St.AL.
EPG.1
EPG.2
:
PrG.6
Auto (On,Off)
Audi.(On,Off)
Edit
EPG.1
EPG.2 St.01
EPG.3 :
St.30
P.End
PAn (0-255)
:
dimr. (0-255)
F.tim.(0-255)
S.tim. (0-255)
COPY.
MaSt.
EPG1
:
PrG.6
SLA.
rESE.
SPEC.
uPd.M.(No,Yes)

12
13
7. Functions of the control panel
The control panel situated on the front panel of the base offers several features. You can simply set the DMX address,
run programs, make a reset and also use many functions for setting the xture behaviour.
Control elements on the control board:
[MODE] button-leaves menu without saving changes.
[ENTER] button- enters menu,conrms adjusted values and leaves menu.
[UP] button and[DOWN] button- moves between menu items on the the same level, sets values.
After switching the xture on,the display shows the initial screen:
Use [UP],[DOWN] to browse through the menu. To select a function or submenu,press [ENTER].
7.1 Fixture Address
Use this menu to set the DMX start address of the xture, which is dened as the rst channel from which the ArcWash
Recessed 136 RGB will respond to the controller.
If you set, for example, the address 15, the ArcWash Recessed 136 RGB will use the channel 15 to 28 for control (if Mode
1 is selected).
Please, be sure that you don’t have any overlapping channels in order to control each ArcWash Recessed 136 RGB
correctly and independently from any other xture on the DMX data link.
If two, three or more ArcWash Recessed 136 RGB are addressed similarly, they will work similarly.
After having addressed all ArcWash Recessed 136 RGB, you may now start operating these via your lighting control-
ler.
Note: After switching on, the ArcWash Recessed 136 RGB will automatically detect whether DMX 512 data is received
or not.
If there is no data received at the DMX-input, the display will start to ash „A001” with actually set address.
This situation can occur if:
- the 3 PIN XLR plug (cable with DMX signal from controller) is not connected with the input of the ArcWash Recessed
136 RGB.
- the controller is switched off or defective, the cable or connector is defective or the signal wires are swaped in the input connec-
tor.
7.2 Fixture informations
Use this menu to read an useful information about the xture.
tEMP ---Fixture temperature.The function shows the temperature in the xture head (°C).Please note that the outside
temperature should not exceed 40° C.
VErS. --- Software version.Select this function to read the software version of processors:
IC1.b.--- Main processor on the main board in the xture base
IC2.b.--- Pan/tilt processor on the main board in the xture base
7.3 Personality
Use this menu to to modify the ArcWash Recessed 136 RGB operating behavior.
r.PAn --- Pan reverse.Select this function to invert the pan movement.
r.tilt --- Tilt reverse.Select this function to invert the tilt movement.

12
13
DM.Pr. --- DMX preset.Select this item to choose desired DMX mode.Please refer to the chapter "DMX protocol" for
detail description.
Mi.SE. --- Microphone sensitivity.Select this function to adjust the microphone sensitivity from 1(maximum) to
20(minimum).If the sensitivity is correctly adjusted,the upper segment of the rst digit blinks in the bass beat.
Examples:
underexited right level overexited
(upper segment blinks)
FEEd --- Pan/Tilt feedback.This function allows to return the mowing head to the required pan/tilt position after changing
the position by external force (e.g.by stroke).
Be careful, the Pan/Tilt Feedback OFF is not the standard operation and the head of the xture can be de-
maged!
Note: If the feedback was switched off ,the pan/tilt-position is changed by an external force and the feedback is switched
on again,the moving head might not to be synchronized with the DMX signal.You have to make a reset in order to syn-
chronize the moving head with the DMX signal.
P.t.Mo. --- Pan/tilt movement mode.Use this menu to set the character of the pan/tilt movement.
ti.Mo. --- Time mode.Pan and tilt will move with different speeds and they will come at the same
time to end point (pan and tilt sets its optimal speed).
SP.Mo. --- Speed mode.Pan and tilt will move with the same speed as adjusted at the channel 5
(Pan/Tilt speed).E.g. pan will come to the end point and wait for tilt,which has longer track.
bL.Co. --- Blackout during movement correction.Select this function to enable the blackout during the head movement
correction (if the moving head lost its right pan/tilt position for a short moment).
bl.P.t. --- Active Blackout while Pan/Tilt moving: - Use this function if you wish to close the light output during
pan/tilt changes.
bALA. --- Balance.Select this function to enable (On) or disable (OFF) the white balance which is set in "White colour
balance" menu below.If this function is set OFF,ArcWash Recessed 136 RGB will use maximum values (255) of satura-
tion for red, green and blue channel.
C.bAL. --- White colour balance. Using this menu you can set the white balance:
1. Browse through the menu by pressing the [UP] and [DOWN] buttons until the display shows "C.bAL." menu.Press
[ENTER] button and "rEd.b." will appear on the display.
2.Press [ENTER] button again and use [UP] and [DOWN] buttons to adjust the new maximum value required for the red
channel.Conrm your choice by pressing [ENTER].Use the [UP] and [Down] buttons to select next colour.
3.Repeat step 2 for green channel "GrE.b." and for blue channel "bLu.b".
i.bLi. --- Initial blink.If this function is on,ArcWash 136 RGB makes auto-calibration (All LEDs light on 100% for a short
time) after switching the xture on.If this function is set off,you have to set manually every colour on max.brightness after
switching on the driver before starting regular operating.This action should last min. one second for every colour.
dF.SE. --- Default Settings .Select this option to reset all xture personalities to the factory values.
7.4 Manual mode
Select this menu to control channel effects by control buttoms on the control board without an external controller.
PAn a coarse pan movement GrEE a green LED saturation
F.PAn a ne pan movement bLuE a blue LED saturation
tilt a coarse tilt movement MACr a colour macros
F.tilt a ne tilt movement Stro. a strobe,shutter
SpEd a pan/tilt speed dimr a dimmer
P.t.SE. a pan/tilt macro selection
P.t.SP. a pan/tilt speed
Func. a special function
rED a red LED saturation

14
15
7.5 Test sequences
Use this menu to to run a demo-test sequences without an external controller, which will show you some possibilities of
using ArcWash Recessed 136 RGB.
7.6 Stand-alone setting
The xtures on a data link are not connected to the controller but can execute pre-set programs which can be different for
every xture. “Stand-alone operation” can be applied to the single xture or to multiple xtures operating synchronously.
Synchronous operation of multiple xtures requires that they must be connected on a data link and one of them is set as
a master (“MSt“) and the rest as the slaves (“SLA“). Up to 32 xtures can be connected in master/slave chain.Only one
xture can be set as the master.
Note: Disconect the xtures from the DMX controller before master/slave operating, otherwise data collisions can occur
and the xtures will not work properly!
It’s necessary to insert the XLR termination plug (with 120 Ohm) into the input of the master xture and into the output of
the last slave xture in the data link in order to ensure proper transmission on the data link.
Operating multiple xtures in stand-alone mode.
1.Select one xture and set it as a master and select a program which is to be played (Menu path: "St.AL."--->"MASt.").
2.The rest of the xtures set as slaves (Menu path: "St.AL."--->"SLA.").
3.Build the master/slave chain.(See chapter “DMX-512 connection and Master/Slave connection“).
Audi --- Music trigger.Select this function to enable the sound control of the running programs via the built-in micro-
phone.
EPG1-PrG.6 --- Fixture programs.By pressing [ENTER] selected program will run in a loop.
Auto. --- Automatically playback. If this function is on, the xture in DMX mode remembers last running program and
this program will run after switching the xture on .
Edit --- Editing program.The xture includes 6 built-in programs (PrG.1-PrG.6) and 3 free editable programs (EPG.1-
EPG.3) each up to 30 steps.Every program step has a fade time-the time during which effects (except pan/tilt) go to the
current step and a standing time-the time,during which effects last in the current step.
Programming procedure:
1. Enter "Edit." menu
2. Press [UP] or [DOWN] to select the desired program which you wish to edit and press [ENTER].
3. Press [UP] or [DOWN] to select the desired program step ("St.01" - "St.30") and press [ENTER].
4. Press [UP] or [DOWN] to select the desired item and press [ENTER] button.Now you can edit by using [UP] or [DOWN]
buttons the DMX values of selected item:
P.End. - a total number of the program steps (value 1-30).This value must be set
before start programming(e.g. if you want to create program with 10 steps,set
P.End=10).
PAn a coarse pan movement GrEE a green LED saturation
F.PAn a ne pan movement bLuE a blue LED saturation
tilt a coarse tilt movement MACr a colour macros
F.tilt a ne tilt movement Stro. a strobe,shutter
SpEd a pan/tilt speed dimr a dimmer
P.t.SE. a pan/tilt macro selection
P.t.SP. a pan/tilt speed
rED a red LED saturation
F.tim. - fade time,value 0-255 *
S.tim. - standing time,value 0-255 *
COPY. - copying the current prog. step to the next prog. step.
Press [ENTER]-button to conrm adjusted value.
5.Repeat steps 3 and 4 for next prog.step.If you want to copy current prog. step to the next prog.step, select option
"COPY."and conrm it by pressing [ENTER].

14
15
*Both Fade time and Standing time use the same conversion table in order to convert DMX value to the time value:
DMX Time
[sec.]
DMX Time
[min.]
DMX Time
[min.]
DMX Time
[min.]
DMX Time
[min.]
10.1 50 4.2 105 18.4 160 42.7 215 77
20.4 55 5110 20.2 165 45.4 220 80.7
52.5 60 6115 22 170 48.2 225 84.4
10 10 65 7120 24 175 51 230 88.2
15 22.5 70 8.2 125 26 180 54 235 92
20 40 75 9.4 130 28.2 185 57 240 96
25 62.5 80 10.7 135 30.4 190 60.2 245 100
30 90 85 12 140 32.7 195 63.4 250 104
35 122.5 90 13.5 145 35 200 66.7 255 108
40 160 95 15 150 37.5 205 70
45 202.5 100 16.7 155 40 210 73.5
Exact expression of the time value follows the formula: time[sec.]=(DMX value)2/10.
MASt. --- Master.Enter this menu if you want to set the the xture as a master.Use [UP] and [DOWN] buttons to select
desired program and press [ENTER] to conrm selection.
SLA. --- Slave.Select this menu if you want to set the the xture as a slave.
7.6 Reset function
This option enables the ArcWash Recessed 136 RGB to index all effects and return them to their standard positions.
7.7 Special functions
Use this menu for special services like software update.
uPd.M. ---Updating mode.Using this function you can update software in the xture via PC and serial link.
The following are required in order to update software:
- PC running Windows 95/98/2000/XP or Linux
- DMX Software Uploader
- Flash cable RS232/DMX (No.13050624)
Note1:Software update should execute a qualied person.If you lack qualication, do not attempt the update
yourself and ask for help your ROBE distributor.
Note 2:DMX address, IP address ,programs 1-3 and all functions in menu "PErS" will be set to their default values.
To update software in the xture:
1.Installation of DMX Software Uploader.
1.DMX Software Uploader program is available from the ROBE web site at WWW.robe.cz.
2.Make a new directory ( e.g. Robe_Uploader) on your hard disk and download the software to it.
3.Unpack the program from the archive. If the Robe xture is produced in magnetic and electronic
ballast version, name of DMX Software Uploader is the same for both versions.
2.Fixture software updating.
1.Determine which of your COM port is available on your PC and connect it with to the DMX input
of the fixture using the uploading cable. Do not extend this cable! Disconnect the fixture from the
other xtures in DMX chain! Turn on the computer and the xture. Make sure the lamp is
switched off.
2.Switch the xture to the update mode by selecting the option Updating mode in menu Special
Functions on the xture control panel:SPEC-->UPd-->yES.(From this option you cannot return back
to the main menu. If you do not want to continue in software update, you have to switch off and on the xture
to leave this option!)

16
17
3.It is recommended that you exit all programs before running the Software Uploader.
4.Start the Software Uploader program. Select desired COM and then click Connect button.
If the conection is OK, click Start Uploading button to start uploading. It will take several minutes to
perform software update. If the option "Incremental Update"isn´t checked ,all processors will be
updated (including processors with the same software version).
If you wish to update only later versions of processors, enable the Incremental Update check box.
Avoid interrupting the process. Update status is being displayed in the list window.
When the update is nished, the line with the text “The xture is successfuly updated‘ will appear in
this window and the xture will reset with the new software.
Note: In the case of interruption of the upload process (e.g. power cut), the xture remains in the update mode and you
have to repeat the software update again.
For example: The xture was switched off before nishing software upload. After switching the xture on again, the xture
is still in the update mode and the display is dark. Restart the Software Uploader program and repeat software update
from your PC.
8. Power down mode
This mode omits xture reset after switching the xture on and lowers motor powers of the xture. „Power down mode”
is useful in special casech. g. if the xture is in a ight case and you want to set its DMX address without taking it out
from the case. To enter „Power down mode”, press and hold [UP] and [DOWN] and at the same time switch on the Power
switch. The following message appears on the display: “P.d.Mo.”
Press [ENTER] to activate „Low power mode” without xture reset. Now you can set features and behaviour of the xture
by using “Pers.” menu. If you want to go „normal operation mode”, execute xture reset.
Note: All motors in “Power down mode” are deactivated.
9. Error and information messages
PA.Er. (Pan-yoke movement error)
This message will appear after the reset of the xture if the yoke’s magnetic-indexing circuits malfunction (sensors failed
or magnet missing) or the stepping motor is defective. (Or its driving IC on the main PCB). The yoke is not located in the
default position after the reset.
ti.Er. (TILT-head movement error)
This message will appear after the reset of the xture if the head’s magnetic-indexing circuit malfunctions (sensor failed
or magnet missing) or the stepping motor is defective. (Or its driving IC on the main PCB). The head is not located in the
default position after the reset.

16
17
10. Technical specications
Power supply
- Input Voltage:100-240V AC, 50/60 Hz
- Fuse:T 2 A
- Max.Pover Consumption:100 VA
Optical system
- 36 RGB LEDs
- Standard 6° beam angle lenses
- Optional 25° beam angle lenses
Beampath
Strobe
- Strobe effect with variable speed (max. 25 ashes per second)
- Preprogrammed random strobe pulse-effects
Dimmer
- Smooth dimmer from 0 - 100 %
Motors
- 2 high quality stepping motors controlled by microprocessors
Electronics
- Addressing, special functions setting, manual control via control panel with 4-digit LED display
- Built-in analyzer for easy fault nding, error messages
- Bilt-in demo sequences
- Black-out while head moving
- Silent fans cooling
- Digital serial input DMX-512
- Master/slave operation
- DMX-control via every standard DMX controller
- control channels: 8 or 14
Pan/Tilt
- Pan movement range 530°
- Tilt movement range 280°
- 8/16 bit movement resolution
- Automatic pan/tilt position correction
- Remotely controllable speed of pan/tilt movement for easy programming
Rigging
-Ceiling box for 600x600 or 625x625 mm grid mounting or version for plaster-boards
-Integral attachment points for wire hangers or all-thread support
Distance (m)
Red
Green
Blue
White
Diameter (m)
0.5 1.0 1.5 2.0 3.0 4.0 5.0
9152/850
18688/1736
1984/184
32576/3026
0.05
2288/213
4672/434
496/46
8144/757
0.1
1016/94
2076/193
220/20
3620/336
0.16
572/53
1168/109
124/12
2036/189
0.2
254/24
519/48
55/5
905/84
0.31
143/13
292/27
31/3
0.42
478/44
92/6
187/17
20/2
306/28
0.52
Intensity (center)
Lux/Footcandles
6°
Beam angle 6°
1.5
1.0
0.5
0
0.5
1.0
1.5
5 Distance (m)
0.2 0.31 0.42 0.52 Diameter (m)
2 3 4
Beam opening (m)
1
00.1
0.5
01.5
0.05 0.16
0
600
450
300
150
0
(LUX)
1 0.8 0.6 0.2 0.2 0.4 0.6
Diameter (m)
Distance=4m
0.4 0.8 1
56
42
28
14
0
(Foot-candles)
white red green blue

18
19
Data input/output
- 3-pin XLR male socket for DMX data input
- 3-pin XLR female socket for DMX data output
Temperatures
- Maximum ambient temperature: 40° C
- Maximum housing temperature: 55° C
Minimum distances
- Min. distance from ammable surfaces: 0.5 m
- Min. distance to lighted object: 0.5 m
Dimensions (mm) -version for 600x600mm mounting grid:
Weight - moving head:
8.8 kg
Weight -ceiling box:
7.0 kg
Accessories
- Frost lm lter (soft).......................................................................No. 14060091
- Frost lm lter (dense)...................................................................No. 14060092

18
19
Optional accessories:
- Flash cable RS232/DMX ...............................................................No.13050624
11. Maintenance and cleaning
It is absolutely essential that the xture is kept clean and that dust, dirt and smoke-uid residues must not build up on or
within the xture. Otherwise, the xture‘s light-output will be signicantly reduced. Regular cleaning will not only ensure
the maximum light-output, but will also allow the xture to function reliably throughout its life.
A soft lint-free cloth moistened with any good glass cleaning uid is recommended, under no circumstances should alcohol
or solvents be used!
DANGER !
Disconnect from the mains before starting any maintenance work
The front objective glass will require weekly cleaning as smoke-uid tends to building up residues, reducing the light-output
very quickly. The cooling-fans should be cleaned monthly.
The interior of the xture should be cleaned at least annually using a vacuum-cleaner or an air-jet.
More complicated maintenance and service operations are only to be carried out by authorized dealers.
Replacing the fuse
If the lamp burns out, the ne-wire fuse of the device might fuse, too. Only replace the fuse by a fuse of same type and rating.
Before replacing the fuse, unplug mains lead.
Procedure:
1) Unscrew the fuseholder on the rear panel of the base with a tting screwdriver from the housing (anti clockwise).
2) Remove the old fuse from the fuseholder.
3) Install the new fuse in the fuseholder.
4) Replace the fuseholder in the housing and x it.

20
21
12. Ceiling boxes - versions and dimensions