Anritsu MS2024A Use and care manual

Is there a problem updating firmware using USB interface?
An intermittent problem occurs with firmware updates using the USB interface with several of the
hand held test instruments. The list of instruments includes the MS2024A, MS2026A, MS2034,
MS2036A, MS2717A/B, MS2718B, MS2719B, MS2721A/B, MS2723B, MS2724B, MS8911A/B,
MT8220A and MT8222A. After the update is completed, the instrument may fail to boot properly.
If you have an instrument that fails to boot after a failed firmware update, use the following steps
to resolve the problem.
1. Close Master Software Tools and then re-open it.
2. Power off the instrument. Connect it via Ethernet to your local network or directly to your
PC using an Ethernet cross-over cable.
3. Power up the instrument into bootstrap mode. Hold the 1st, 3rd and 5th soft keys,
located right of the display directly below the "Esc" key, then press the Power button.
Keep the 3 soft keys pressed until the Anritsu logo appears on the display. The Bootstrap
screen will appear after a few seconds.
1

4. Press the Ethernet Configuration soft key.
•If your instrument is configured for DHCP, it will immediately attempt to obtain
(lease) an IP address from the network DHCP server and display it at the bottom
left hand corner of the screen. If successful, note and write down the address,
press the Back soft key and go to step #7.
•If the test instrument cannot obtain an IP address from the DHCP server, it will
time out in approximately after 3 minutes. The statement “DCHP Lease Failed”
will be displayed at the bottom left hand corner of the screen. Go to Step 4a,
DHCP Mode 2nd Attempt.
•If your instrument is configured for STATIC IP, it will open to the Static IP
configuration window displaying the current Static IP address at the bottom left
hand corner of the screen. To reconfigure the Static IP address, go to Step 4b,
Static Address Mode.
a. DHCP Mode 2nd Attempt
i. Press the 1st soft key. (No text describes it.) The Static IP configuration
window opens.
ii. Confirm that the connections, the Ethernet line and communication on
the LAN to the test instrument are OK.
iii. Re-attempt to obtain an IP address through DHCP configuration. Press
the 1st soft key, Toggle the address mode (DHCP/Static), to switch to
DHCP configuration and automatically obtain an IP address. Note the IP
address assigned to the instrument.
iv. Press the Back soft key. Return to the main bootstrap screen and go to
Step #5.
b. Static Address Mode
i. Press the 2nd soft key. Enter the IP address.
ii. Press the 3rd soft key. Enter the gateway address.
iii. Press the 4th soft key. Enter the subnet mask.
iv. Attach the Ethernet cross-over cable between the test instrument and
your PC.
v. Press the Back soft key, to return to the main bootstrap screen.
5. Press the Update OS (Ethernet) soft key. The unit should give you a "Waiting for OS
download connection…" message.
2

6. In Master Software Tools, go to the Tools menu and click Product Updates.
7. The Product Updates window opens. At this point, Master Software Tools is not
connected to your instrument.
8. Highlight the firmware you wish to load into your instrument. If its status is “Ready” the
file is located on the PC and the Emergency Repair button is active. If the file status is
listed as “Available”, click on the Retrieve File button to download the file from the
Anritsu website to your PC. Once the file has been downloaded, its status will be
changed to Ready. Highlight that file.
Note: For Files Not Listed
If the file you are looking for is not on the list –
a. Click the Check for Updates button to obtain the latest list from the Anritsu
website. This will update the Products Updates Screen.
3

If a zip file was sent to you from Anritsu Company –
a. Copy it to the MST folder. (Default location is C:\Program Files\Anritsu\Anritsu
Master Software Tools\Archives )
b. Select the box next to Show Obsolete Files at the bottom of the Product
Updates screen. This updates the list.
9. Click the Emergency Repair button. The OS Recovery window will open.
10. Click the Ethernet button.
a. Enter the IP address of the instrument.
b. Click the Install New OS Now button. Master Software Tools will connect to your
instrument and proceed to install the firmware. Progress messages will appear
above the buttons. Be patient, the installation can take many minutes.
11. When it is done loading the new OS firmware, the instrument should automatically
reboot. If it does not re-boot, power the instrument off then on. The instrument should
start up normally.
4