ANTAIRA INJ-C200G-60-24-T-AIX User manual

Antaira Technologies
INJ-C200G-60-24-T-AIX
Industrial IEEE 802.3bt Gigabit Type 3 4PPoE Injector; EOT:
-40°C ~ 75°C - This injector is designed for use with Axis
Q6055-e MKii PTZ camera requiring High Power (up to 60 watts)
Quick Installation Guide
Version 1.0
(Feb 2023)
Tel: [phone]
Fax: [phone]
www.antaira.com
Package Check List
The package contains the following items:
⚫1 –Quick Installation Guide
⚫1 –INJ-C200G-60-24-T-AIX
⚫1 –Wall Mounting Bracket Set with Screws
⚫1 –Terminal Block
Front Panel Layout
Top Panel View
INJ-C200G-60-24-T-AIX top panel is equipped with one 4-pin
removal terminal block connector for dual DC power inputs
(9~48VDC).
Product Overview
System Interface/Performance
10/100/1000BaseT Power over Ethernet Injector
Provides Power Feeding up to 60 Watts
Overload Current Protection
Power Input & Connection
DC 9~48V a 4-Pin Removal Terminal Block
Operating Temperature
Extended Operating Temperature (-T): -40°C to 75°C
Case/Installation
IP30 Protection
Installation in a Pollution Degree 2 Industrial Environment
DIN-Rail and Wall Mount Design
LED Indicators
LED
Color
Description
Power
Green
On
Power input is active
Off
Power input is inactive
PoE
Green
On
The port is supplying power to the powered-device
Off
No powered-device attached or power supplyingfails
Quick Installation
Ethernet Ports
RJ45 Ports (Auto MDI/MDIX)
All RJ45 ports are auto-sensing for 10Base-T, 100Base-TX, and
1000Base-T(X) device connections. Please follow the wiring pin
assignment table below for Ethernet port installation.
Grounding Screw
(Behind)
LED for PoE
Ethernet Port for Data
Ethernet Port for PoE and Data
LED for Power
Grounding Screw
4-Pin Removal Terminal Block
(Power Input)
Terminal Block

Power Input Wiring
Please follow the steps below to insert the power wire:
1. Insert the positive and negative wires into the V+, V-
contacts on the terminal block connector as shown
below in Figure 1.
2. Tighten the wire-clamp screws to prevent the wires from
loosening, as shown below in Figure 2.
Figure 1
Figure 2
Industrial Switch Mounting
DIN-Rail Mounting
The DIN-Rail bracket is pre-installed on the
industrial Ethernet switch from the factory.
Please refer to Figure 3 for a DIN-Rail
bracket installation reference. Follow the
steps below for installing the industrial
switch on the DIN-Rail track:
1. Insert the top of the DIN-Rail onto the
track as shown below in Figure 4.
2. Lightly pull down the bracket onto the
rail as shown below in Figure 5.
3. Check if the bracket is mounted tightly
on the rail.
4. To remove the industrial
Ethernet
switch
from the rail, do the opposite from the steps above.
Figure 4
Wall Mounting
Follow the steps below to mount the industrial Ethernet switch
using the wall mounting bracket as shown in Figure 6.
1. Remove the DIN-Rail bracket from the industrial Ethernet
switch by loosening the screws.
2. Place the wall mounting brackets on the top and bottom of
the industrial Ethernet switch.
3. Use the screws to screw the wall mounting bracket on the
industrial Ethernet switch.
4. Use the hook holes at the corners of the wall mounting
bracket to hang the industrial Ethernet switch on the wall.
5. To remove the wall mount bracket, do
the opposite from the steps above.
Field Maintenance and Service
⚫If the device requires servicing of any kind, the user is
required to disconnect and remove it from its mounting. The
initial installation should be done in a way that makes this as
convenient as possible.
⚫Voltage/power lines should be properly insulated as well as
other cables. Be careful when handling them so as to not trip
over.
⚫Do not under any circumstance insert foreign objects of any
kind into the heat dissipation holes located in the different
faces of the device. This may not only harm the internal
layout, but might cause harm to the user as well.
⚫Do not under any circumstance open the device for any
reason. Please contact your dealer for any repair needed or
follow the instructions within the manual.
Warranty Policy
Warranty Conditions
Products supplied by Antaira Technologies are covered in this
warranty for sub-standard performance or defective
workmanship. The warranty is not, however, extended to goods
damaged in the following circumstances:
(a) Excessive forces or impacts
(b) War or an Act of God: wind storm, fire, flood, electric shock,
earthquake
(c) Use of unqualified power supply, connectors, or
unauthorized parts/kits
(d) Replacement with unauthorized parts
RMA and Shipping Costs Reimbursement
Customers shall always obtain an authorized "RMA" number
from Antaira before shipping the goods for repair or
replacement.
•Within the warranty period (based on the invoice date), all
parts and labor are free of charge to the customers.
•Customers are responsible for the cost of parts and labor, if
the products are out of warranty.
•For RMA service, customers are responsible for the shipping
expense for shipping the RMA unit(s) to Antaira. Antaira is
responsible for the shipping expense via a ground service
for the return repair/replace unit(s) back to customers.
Limited Liability
Antaira would not be held responsible for any consequential
losses from using Antaira’s product.
Warranty Period
5-Year Warranty
Antaira’s Customer Service and Support
•Antaira’s Technical Service & Support Centers:
+ 844-268-2472 (Antaira US Headquarter)
+ 48-22-862-88-81 (Antaira Europe Office)
+ 886-2-2218-9733 (Antaira Asia Office)
•Antaira’s Web Sites & Repair/Support Emails:
www.antaira.com / [email protected]
www.antaira.eu / [email protected]
www.antaira.com.tw / [email protected]
*Any changes will be announced on the Antaira website.
Figure 3
Figure 6
Figure 5