ANTAIRA STE-6104C Series User manual

STE-6104C Series
4-Port Serial Device Server
Quick Start Guide
Version 1.2
November 2018
This document is intended to provide customers with
brief descriptions about the product and assist customers
to get started. For detailed information and operation of
the product, please refer to the product user’s manual in
the product CD or ANTAIRA website.
1. PACKAGING
Check whether your package contains following items:
◎STE-6104C
◎Quick Start Guide with Warranty Card
◎Product CD
◎7-pin Terminal Block ( 2ESDV-07P) x1
2. HARDWARE DESCRIPTION
NOTE:
1. STE-6104C (RS-232/422/485)
2. Press the Default button of STE-6104C to reset to the
default value
Figure 2.1. STE-6104C Series interfaces
LED Indicators:
Name Color Status Description
Power Green Off Power is not connected
On Power is connected
LAN Green Off Ethernet Disconnected
Blinking Data is transmitting on
Ethernet for 100Mbps
Orange Blinking Data is transmitting on
Ethernet for 10Mbps
COM Green Off No data is transmitting on
COM port
Blinking Data is transmitting on
COM port
RUN Green Off System is not ready or
halt
Blinking AP firmware is running
normally
Installation Procedures:
Step 1: Connect STE-6104C to power source
Step 2: Connect STE-6104C to the Ethernet network. Use
a standard straight-through or cross-over Ethernet
cable Always make sure the PC is on the same
network subnet as STE-6104C.
Step 3: Connect STE-6104C’s serial port to a serial
device.
Step 4: Mount STE-6104C to a Din Rail.
3 SOFTWARE SETUP
Default Network Setting:
Default User Name/Password:
LAN1 IP: 10.0.50.100
User Name: admin
Gateway: 10.0.0.254
Password
Version 455 and earlier
null (leave it blank)
Version 456 and later
“default”
Subnet: 255.255.0.0
LAN2 IP：192.168.1.1
Gateway: 192.168.1.254
Subnet: 255.255.255.0
Version 1.1 March, 2011

Auto IP (Dynamic IP):
A DHCP server can automatically assigns the IP address
and all the network settings. STE-6104C supports the
DHCP client function. By default, the DHCP client function
on STE-6104C is disabled; you may activate the DHCP
client functions by executing SerialManager Utility ( Figure
3.1)
Figure 3.1. SerialManager utility Dialog Window
Assign a Static IP address by:
1. Configuration by Telnet
i. Telnet to STE-6104C using DOS command
“Telnet IP_address 23”. Example: telnet
10.0.50.100 23
ii. STE-6104C’s network, link mode and COM
ports settings can be configured in the telnet
window
2. Configuration by SerialManager Utility
i. Use SerialManager Utility on Product CD or
our website to configure STE-6104C. First
click ”Config” then assign a static IP.
3. Configuration by Web Browser
i. Open a web browser, then Enter in the IP
address as the STE-6104C. The default user
name is admin and default password is null
(leave it blank) or “default” depending on
firmware version.
ii. The STE-6104C’s network, link mode and COM
ports settings can be configured on different web
pages.
iii. Click “Save Configuration” to save settings.
Warranty Policy
Warranty Conditions
Products supplied by ANTAIRA Technologies are
covered in this warranty for sub-standard performance or
defective workmanship. The warranty is not,
however, extended to goods damaged in the following
circumstances:
(a) Excessive forces or impacts
(b) War or an Act of God: wind storm, fire, flood, electric
shock, earthquake
(c) Use of unqualified power supply, connectors, or
maintenance procedure
(d) Replacement with unauthorized parts
RMA and Shipping Costs Reimbursement
Customers shall always obtain an authorized "RMA"
number from ANTAIRA before
shipping the goods to be repaired to ANTAIRA. When in
normal use, a sold product shall
be replaced with a new one within 3 months after
purchase. The shipping cost from
the customer to ANTAIRA will be reimbursed by
ANTAIRA.
After 3 months and still within the warranty period, it is up
to ANTAIRA whether to replace the unit with a new one;
normally, as long as a product is under warranty, all
parts and labor are free of charge to the customers.
After the warranty period, the customer shall cover the
cost for parts and labor.
Three months after purchase, the shipping cost from the
customer to ANTAIRA will not
be reimbursed, but the shipping cost from ANTAIRA to
the customer will be paid by ANTAIRA.
Limited Liability
ANTAIRA shall not be held responsible for any
consequential losses from using ANTAIRA’s
product.
Warranty Period
*Notes: Warranty coverage for Accessories such as
power adaptors and high-gain antenna is one year.
The Warranty Certification will not be effective until an
authorized stamp issued by ANTAIRA’s overseas agents.
Purchase Date: / / (yyyy/mm/dd)
Serial Number:
※ANTAIRA Customer Services and Supports
1. Please contact your local dealers or ANTAIRA technical
support center at the following numbers.
1-877-ANTAIRA-5 (1-877-229-3665)
2. Please report the defected problems via ANTAIRA’s
Web site or E-mail account
Web Site:www.ANTAIRA.com e-mail:
[e-mail]
Product Categories Warranty
Serial-to-Ethernet Server
5 Years
Serial-to-WLAN Server
Industrial Wireless Ethernet Device
Modbus Gateway Series
Industrial Ethernet Switch
Embedded Serial Server
Pick-to-Light System
1 Year
Auto-Identification and Data
Collection-AIDC