ANTAIRA LMP-0800G-24 User manual

Antaira Technologies - Industrial Ethernet Switches
LMP-0800G-24 Series User Manual V1.0
i
LMP-0800G-24 Series
8-Port Industrial PoE+ Gigabit Managed Ethernet Switches
8*10/100/1000Tx (30W/Port); 12~36VDC Power Input (w/ Voltage Booster)
Version 1.0
User Manual

Antaira Technologies - Industrial Ethernet Switches
LMP-0800G-24 Series User Manual V1.0
ii
© Copyright 2015 Antaira Technologies, LLC
All Rights Reserved
This document contains information, which is protected by copyright. Reproduction, adaptation or translation
without prior permission is prohibited, except as allowed under the copyright laws.
Trademark Information
Antaira is a registered trademark of Antaira Technologies, LLC, Microsoft Windows and the Windows logo are the
trademarks of Microsoft Corp. NetWare is the registered trademark of Novell Inc. WMM and WPA are the
registered trademarks of Wi-Fi Alliance. All other brand and product names are trademarks or registered
trademarks of their respective owners.
Notice: Copyrights © 2015 by Antaira Technologies, LLC. All rights reserved. Reproduction, adaptation, or
translation without prior permission of Antaira Technologies, LLC is prohibited, except as allowed under the
copyright laws.
Disclaimer
Antaira Technologies, LLC provides this manual without warranty of any kind, expressed or implied, including but
not limited to the implied warranties of merchantability and fitness for a particular purpose. Antaira Technologies,
LLC may make improvements and/or changes to the product and/or specifications of the product described in this
manual, without prior notice. Antaira Technologies, LLC will not be liable for any technical inaccuracies or
typographical errors found in this guide. Changes are periodically made to the information contained herein and
will be incorporated into later versions of the manual. The information contained is subject to change without prior
notice.

Antaira Technologies - Industrial Ethernet Switches
LMP-0800G-24 Series User Manual V1.0
iii
FCC Warning
This equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant to Part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy. It may cause
harmful interference to radio communications if the equipment is not installed and used in accordance with the
instructions. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the grantee of this device could void the user's
authority to operate the equipment.
CE Mark Warning
This is a Class-A product. In a domestic environment this product may cause radio interference in which case the
user may be required to take adequate measures.
Industrial Ethernet Switches
Industrial Grade Gigabit PoE Managed Ethernet Switches
User Manual
Version 1.0 (December 2015)
This manual supports the following models:
LMP-0800G-24
LMP-0800G-24-T
This document is the current official release manual. Please check our website (www.antaira.com) for any
updated manual or contact us by e-mail ([email protected]).

Antaira Technologies - Industrial Ethernet Switches
LMP-0800G-24 Series User Manual V1.0
iv
Table of Contents
1. Introduction................................................................. 1
1.1 Product Overview 1
1.2 Product Software Features 1
1.3 Product Hardware Features 2
1.4 Package Contents 3
1.5 Safety Precaution 3
2. Hardware Description................................................. 4
2.1 Physical Dimensions 4
2.2 Front Panel 5
2.3 Top View 5
2.4 LED Indicators 5
2.5 Reset Button 6
2.6 Ethernet Ports 7
2.7 Cabling 8
2.8 Wiring the Power Inputs 8
2.9 Wiring the Fault Alarm Contact 9
3.Mounting Installation ................................................ 10
3.1 DIN-Rail Mounting 10
3.2 Wall Mounting 11
4.Hardware Installation................................................ 12
4.1 Installation Steps 12
5.Web Management...................................................... 13
5.1 Web Console Configuration 13
5.1.1 About Web-Based Management ............................13
5.2 Basic Setting 15

Antaira Technologies - Industrial Ethernet Switches
LMP-0800G-24 Series User Manual V1.0
v
5.2.1 System Information ................................................15
5.2.2 Admin & Password.................................................16
5.2.3 IP Setting................................................................16
5.2.4 IPv6 Neighbor Cache .............................................17
5.2.5 IPv6 Settings..........................................................18
5.2.6 System Time ..........................................................18
5.3 Port Management 19
5.3.1 Port Status..............................................................19
5.3.2 Port Configuration ..................................................19
5.4 PoE (Power-over-Ethernet) 20
5.4.1 PoE Configuration ..................................................20
5.4.2 Ping Alarm..............................................................21
5.4.3 PoE Schedule.........................................................21
5.5 ERPS 22
5.5.1 ERPS Status ..........................................................23
5.5.2 ERPS Configuration ...............................................24
5.5.3 Before Configuring ERPS.......................................26
5.6 Spanning Tree 34
5.6.1 RSTP Status...........................................................34
5.6.2 RSTP Configuration ...............................................35
5.6.3 MSTI Status............................................................37

Antaira Technologies - Industrial Ethernet Switches
LMP-0800G-24 Series User Manual V1.0
vi
5.6.4 MSTI Configuration ................................................37
5.7 IGMP Snooping 40
5.7.1 IGMP Settings........................................................40
5.7.2 IGMP Snooping Status Table.................................41
5.8 802.1Q VLAN 41
5.8.1 802.1Q VLAN Settings ...........................................42
5.9 QoS (Traffic Prioritization) 43
5.9.1 QoS Classification..................................................44
5.9.2 CoS Mapping..........................................................45
5.9.3 ToS Mapping..........................................................45
5.10 Port Trunk 46
5.10.1 Trunk Status.........................................................47
5.10.2 Trunk Configuration..............................................47
5.11 Port Mirroring 48
5.12 SNMP 49
5.12.1 SNMP Agent.........................................................49
5.12.2 SNMP Trap Setting ..............................................51
5.13 DHCP Server / Rely 52
5.13.1DHCP Client .........................................................54
5.13.2 DHCP Server........................................................54
5.13.3 DHCP Server Binding...........................................55
5.13.4 DHCP Relay.........................................................56

Antaira Technologies - Industrial Ethernet Switches
LMP-0800G-24 Series User Manual V1.0
vii
5.14 802.1X 57
5.14.1 802.1X Settings....................................................57
5.14.2 Local Database ....................................................58
5.14.3 RADIUS Server ....................................................59
5.15 UPnP 60
5.15.1 UPnP....................................................................60
5.16 Modbus TCP 61
5.16.1 Enable Modbus TCP ............................................61
5.16.2 MODBUS Data Map and Information ...................62
5.17 System Warning 68
5.17.1 Syslog Setting ......................................................68
5.17.2 System Event Log ................................................69
5.17.3 SMTP Setting.......................................................69
5.17.4 Event Selection ....................................................70
5.17.5 Fault Alarm...........................................................71
5.18 MAC Table 71
5.18.1 MAC Address Table .............................................71
5.18.2 MAC Table Configuration.....................................72
5.19 Maintenance 72
5.19.1 Upgrade................................................................72
5.19.2 Reboot..................................................................73
5.19.3 Default..................................................................73

Antaira Technologies - Industrial Ethernet Switches
LMP-0800G-24 Series User Manual V1.0
viii
5.20 Configuration 73
5.20.1 Save.....................................................................74
5.20.2 Backup & Restore ................................................74
5.20.3 Auto Load & Backup.............................................75
5.21 Logout 75
6. Command Line Interface Management................... 76
6.1 About CLI Management 76
7. Technical Specifications.......................................... 95

Antaira Technologies - Industrial Ethernet Switches
LMP-0800G-24 Series User Manual V1.0
1
1. Introduction
All Antaira industrial managed switches come with a pre-installed “user-friendly” web console interface,
which allows users to easily configure and manage the units, whether one is using a serial console and
command line interface(CLI) commands like Telnet, SSH, HTTP (Web GUI) or simple network
management protocols (SNMP).
1.1 Product Overview
Antaira Technologies’LMP-0800G-24 series is an 8-port industrial Gigabit PoE+ managed Ethernet
switch embedded with 8*10/100/1000Tx Ethernet ports that support IEEE802.3at/af for a maximum of
30W/port. It is a fully manageable Layer 2 Ethernet switch that is pre-loaded with a user-friendly web
management console design. It supports the ring network redundancy function using the market’s open
standard ITU-T G.8032 ERPS (Ethernet Ring Protection Switch) protocol that has a <50ms network
recovery time. The advanced network filtering and security functions, such as, IGMP, VLAN, QoS,
SNMP, port lock, RMON, ModbusTCP, and 802.1X/HTTPS/SSH/SSL increase determinism and
improve network management for remote SCADA systems or control networks.
The LMP-0800G-24 series is IP30 rated and DIN-rail mountable. There are also two wide operating
temperature models for either a standard temperature range (STD: -10°C to 70°C) or an extended
temperature range (EOT: -40°C to 75°C). This series supports a dual power input having a low voltage
range (12~36VDC) and a built-in voltage booster allowing the unit to give a full 48VDC PoE power for
any mobile PoE application or any low voltage power sourcing environment. It also provides high EFT
and ESD protection for industrial networking applications, such as, power/utility, water wastewater,
oil/gas/mining, factory automation, security surveillance, ITS and any other outdoor or harsh
environment.
1.2 Product Software Features
Network Redundancy
STP, RSTP, MSTP, ITU-T G.8032 Ethernet Ring Protection Switch (ERPS) for network
redundancy
Network Management
Web UI based management, SNMP v1/v2/v3, Serial Console
Qos, traffic classification QoS, Cos, bandwidth control for Ingress and Egress,
broadcast storm control, Diffserv

Antaira Technologies - Industrial Ethernet Switches
LMP-0800G-24 Series User Manual V1.0
2
IEEE802.1q VLAN tagging, port-based VLAN support
IGMP snooping v1/v2, IGMP filtering / throttling, IGMP query up to 256 group
Supports IPv4/IPv6, RMON, MIB II, port mirroring, event syslog, DNS, NTP/SNTP,
HTTPS, SSH/SSL, TFTP
MODBUS TCP for SCADA system integration
Port Configuration
Status, statistics, mirroring, rate limiting, event syslog
Event Handling
Event notification by Email: Cold/Warm Start, Power Failure, Authentication, SNMP
trap and Fault Alarm Relay Output
Software Upgrade via TFTP and HTTP
Configuration Backup –USB Port
1.3 Product Hardware Features
System Interface and Performance
All RJ-45 ports support Auto MDI Function
Embedded 8*10/100/1000Tx (PSE 30W/Port) RJ45 Ports
Store-and-forward switching architecture
8K MAC address table
Power line EFT protection: 2,000VDC; Ethernet ESD protection: 6,000VDC
Power Input
DC 12~36V redundant with a 6-pin removal terminal block
One user programmable alarm relay contact
Operating Temperature
Standard operating temperature models: -10°C to 70°C
Extended operating temperature models: -40°C to 75°C
Case/Installation
IP-30 protection metal housing
DIN-Rail and wall mount design

Antaira Technologies - Industrial Ethernet Switches
LMP-0800G-24 Series User Manual V1.0
3
1.4 Package Contents
1–LMP-0800G-24 series: 8-port industrial gigabit PoE+ managed Ethernet switch, with
8*10/100/1000Tx (PSE 30W/Port)
1-Product CD
2-Wall mounting brackets and screws
1-RJ45 to DB9 Serial Console cable
1-DC cable –18 AWG & DC jack 5.5x2.1mm
1.5 Safety Precaution
Attention: If the DC voltage is supplied by an external circuit, please use a protection
device on the power supply input. The industrial Ethernet switch’s hardware
specs, ports, cabling information, and wiring installation will be described
within this user manual.

Antaira Technologies - Industrial Ethernet Switches
LMP-0800G-24 Series User Manual V1.0
4
2. Hardware Description
2.1 Physical Dimensions
Figure 2.1, below, shows the physical dimensions of Antaira’s LMP-0800G-24 series: 8-port
industrial gigabit PoE+ managed Ethernet switches with 8*10/100/1000Tx ports.
(W x D x H) is 54mm x 99mm x 142mm
Figure2.1
LMP-0800G-24 Series Physical Dimensions

Antaira Technologies - Industrial Ethernet Switches
LMP-0800G-24 Series User Manual V1.0
5
2.2 Front Panel
The front panel of the LMP-0800G-24 series industrial gigabit PoE+ managed Ethernet switch is
shown below in Figure 2.2.
2.3 Top View
Figure 2.3, below, shows the top panel of the LMP-0800G series switch that is equipped with
one 6-pin removal terminal block connector for dual DC power inputs 12~36VDC.
2.4 LED Indicators
There are LED light indicators located on the front panel of the industrial Ethernet switch that
display the power status and network status. Each LED indicator has a different color and has its
own specific meaning, see below in Table 2.1.
Figure2.2
The Front Panel of LMP-0800G-24 Series
Figure2.3
Top Panel View of LMP-0800G-24 Series
6-Pin Removal Terminal Block (Power Input)
Grounding Screw
LED for PWR1, PWR2, and Fault
LAN Port #5~8 –10/100/1000Tx
Hard (Physical) Reset Button
Console Port
USB Backup
LAN Port (1~4) 10/100/1000Tx
LED for 10/100/1000Tx Network Speed Status
LED for PoE Activity

Antaira Technologies - Industrial Ethernet Switches
LMP-0800G-24 Series User Manual V1.0
6
LED
Color
Description
P1
Green
On
Power input 1 is active
Off
Power input 1 is inactive
P2
Green
On
Power input 2 is active
Off
Power input 2 is inactive
Fault
Green/
Red
Green
Power input 1 or 2 is inactive
Red
An applied alarm (such as port disconnect) has been
triggered
Off
Power input 1 and 2 are both functional and no
active/port alarm is detecting errors
Owner
Green
On
ERPS Owner Mode (Ring Master) is ready
Off
ERPS Owner Mode is not active
Ring
Green
On
Ring Network is active
Off
Ring Network is not active
LAN Port 1 ~ 8
(Left LED)
Green
On
Connected to network, 10/100/1000Mbps
Flashing
Networking is active
Off
Not connected to network
LAN Port 1~ 8
(Right LED)
PoE Indicators
Green
On
The port is supplying power to the powered-device
Off
No powered-device attached or power supplying fails
2.5 Reset Button
There is a ‘Reset’button located on the front panel of the industrial Ethernet switch that helps
users to reboot, restore default, or save running configurations by pressing the button for different
seconds. Please refer to Table 2.2 for the timing and function.
Seconds
Function
1
Save running configuration to USB
4-6
Reboot the switch
7 or more
Restore factory default
Table 2.1 - LED Indicators for LMP-0800G-24 Series
Table 2.2 –Reset Button Functions

Antaira Technologies - Industrial Ethernet Switches
LMP-0800G-24 Series User Manual V1.0
7
2.6 Ethernet Ports
RJ-45 Ports
RJ-45 Ports (Auto MDI/MDIX): The RJ-45 ports are auto-sensing for 10Base-T, 100Base-TX, or
1000Base-T connections. Auto MDI means that the switch can connect to another switch or
workstation without changing the straight-through or crossover cabling. See the figures below for
straight-through and crossover cabling schematics.
RJ-45 Pin Assignments
Pin Number
Assignment
1
Rx+
2
Rx-
3
Tx+
6
Tx-
All ports on this industrial Ethernet switch support automatic MDI operations. Users can use
straight-through cables (see figure below) for all network connections to PCs, servers, and other
switches or hubs. With straight-through cabling, pins 1, 2, 3, and 6 are at one end of the cable and
are connected straight through to pins 1, 2, 3 and 6 at the other end of the cable. The table below
(Table 2.3) shows the 10BASE-T/100BASE-TX/1000BASE-T MDI port pin outs.
Note:
The “+” and “-” signs represent the polarity of the wires that make up each wire pair.
Pin MDI-X
Signal Name
MDI Signal Name
1
Receive Data plus (RD+)
Transmit Data plus (TD+)
2
Receive Data minus (RD-)
Transmit Data minus (TD-)
3
Transmit Data plus (TD+)
Receive Data plus (RD+)
6
Transmit Data minus (TD-)
Receive Data minus (RD-)
Table 2.3 - RJ45 Pin Assignments
Table 2.4 - Ethernet Signal Pin

Antaira Technologies - Industrial Ethernet Switches
LMP-0800G-24 Series User Manual V1.0
8
The following figures show the cabling schematics for straight-through and crossover.
2.7 Cabling
Use the four twisted-pair, category 5e, or the above cabling for the RJ-45 port connections. The
cable between the switch and the link partner (switch, hub, workstation, etc.) must be less than 100
meters (328 ft.) in length.
2.8 Wiring the Power Inputs
Please follow the steps below when inserting the power wire.
1. Insert the positive and negative wires into the PWR1 (V1+, V1-) and PWR2 (V2+, V2-) contacts
on the terminal block connector as shown below in Figure 2.6.
2. Tighten the wire-clamp screws to prevent the wires from loosening, as shown below in Figure 2.7.
Note:
Only use copper conductors, 60/75°C, tighten to 5lbs.
The wire gauge for the terminal block should range between 18~20 AWG.
Figure 2.7 - Power Terminal Block
Figure 2.6 - Power Terminal Block
Figure 2.4 Figure 2.5
Straight-Through Cable Schematic Crossover Cable Schematic

Antaira Technologies - Industrial Ethernet Switches
LMP-0800G-24 Series User Manual V1.0
9
2.9 Wiring the Fault Alarm Contact
The fault alarm contact is in the middle of the terminal block connector as the picture shows below
in Figure 2.8. By inserting the wires, it will detect the fault status including power failure or port link
failure (managed industrial switch only) and forma normally open circuit. An application example for
the fault alarm contact is shown below in Figure 2.8.
Note
The wire gauge for the terminal block should range between 12 ~ 24AWG
Figure 2.8 - Wiring the Fault Alarm Contact

Antaira Technologies - Industrial Ethernet Switches
LMP-0800G-24 Series User Manual V1.0
10
3.Mounting Installation
3.1 DIN-Rail Mounting
The DIN-Rail is pre-installed on the industrial
Ethernet switch from the factory. If the DIN-Rail is
not on the industrial Ethernet switch, please see
Figure 3.1 to learn how to install the DIN-Rail on
the switch.
Follow the steps below to learn how to hang the industrial Ethernet switch.
1. Use the screws to install the DIN-Rail bracket on the rear side of the industrial Ethernet switch.
2. To remove the DIN-Rail bracket, do the opposite from step 1.
3. After the DIN-Rail bracket is installed on the rear side of the switch, insert the top of the DIN-
Rail on to the track as shown below in Figure 3.2.
4. Lightly pull down the bracket on to the rail as shown below in Figure 3.3.
5. Check if the bracket is mounted tightly on the rail.
6. To remove the industrial
Ethernet
switch from the rail, do the opposite from the above steps.
Figure 3.1
The RearSide of the Switch and DIN-Rail Bracket
Figure 3.3
Stable the Switch on DIN-Rail
Figure 3.2
Insert the Switch on the DIN-Rail

Antaira Technologies - Industrial Ethernet Switches
LMP-0800G-24 Series User Manual V1.0
11
3.2 Wall Mounting
Follow the steps below to mount the industrial
Ethernet
switch using the wall mounting bracket as
shown below in Figure 3.4.
1. Remove the DIN-Rail bracket from the industrial Ethernet switch by loosening the screws.
2. Place the wall mounting brackets on the top and bottom of the industrial Ethernet switch.
3. Use the screws to screw the wall mounting bracket on the industrial Ethernet switch.
4. Use the hook holes at the corners of the wall mounting bracket to hang the industrial Ethernet
switch on the wall.
5. To remove the wall mount bracket, do the opposite from the steps above.
Below, in Figure 3.5 are the dimensions of the wall mounting bracket.
Figure 3.5
Wall Mounting Bracket Dimensions
Figure 3.4
Remove DIN-Rail Bracket from the Switch

Antaira Technologies - Industrial Ethernet Switches
LMP-0800G-24 Series User Manual V1.0
12
4.Hardware Installation
4.1 Installation Steps
This section will explain how to install Antaira’s LMP-0800G-24 series: 8-port industrial gigabit PoE+
managed Ethernet switches with 8*10/100/1000Tx (PSE: 30W/Port) ports.
Installation Steps
1. Unpack the industrial Ethernet switch from the original packing box.
2. Check if the DIN-Rail bracket is screwed on the industrial Ethernet switch.
If the DIN-Rail is not screwed on the industrial Ethernet switch, please refer to the DIN-
Rail Mounting section for DIN-Rail installation.
If you want to wall mount the industrial Ethernet switch, please refer to the Wall
Mounting section for wall mounting installation.
3. To hang the industrial Ethernet switch on a DIN-Rail or wall, please refer to the Mounting
Installation section.
4. Power on the industrial Ethernet switch and then the power LED light will turn on.
If you need help on how to wire power, please refer to the Wiring the Power Inputs
section.
Please refer to the LED Indicators section for LED light indication.
5. Prepare the twisted-pair, straight-through category 5 cable for Ethernet connection.
6. Insert one side of the RJ-45 cable into switch’s Ethernet port and on the other side into the
networking device’s Ethernet port, e.g. switch PC or server. The Ethernet port’s (RJ-45) LED on
the industrial Ethernet switch will turn on when the cable is connected to the networking device.
Please refer to the LED Indicators section for LED light indication.
7. When all connections are set and the LED lights all show normal, the installation is complete.