ANTAIRA LMX-0802-M User manual

Antaira Technologies - Industrial Ethernet Switches
LMX-0802 Series User Manual V1.0
i
LMX-0802 Series
8-Port Industrial Managed Ethernet Switches
with 6*10/100Tx + 2*100Fx SC or ST Ports
Version 1.2
Hardware Manual

Antaira Technologies - Industrial Ethernet Switches
LMX-0802 Series Hardware Manual V1.2
II
© Copyright 2018 Antaira Technologies, LLC
All Rights Reserved
This document contains information, which is protected by copyright. Reproduction, adaptation or translation
without prior permission is prohibited, except as allowed under the copyright laws.
Trademark Information
Antaira is a registered trademark of Antaira Technologies, LLC, Microsoft Windows and the Windows logo are the
trademarks of Microsoft Corp. NetWare is the registered trademark of Novell Inc. WMM and WPA are the
registered trademarks of Wi-Fi Alliance. All other brand and product names are trademarks or registered
trademarks of their respective owners.
Notice: Copyrights © 2018 by Antaira Technologies, LLC. All rights reserved. Reproduction, adaptation, or
translation without prior permission of Antaira Technologies, LLC is prohibited, except as allowed under the
copyright laws.
Disclaimer
Antaira Technologies, LLC provides this manual without warranty of any kind, expressed or implied, including but
not limited to the implied warranties of merchantability and fitness for a particular purpose. Antaira Technologies,
LLC may make improvements and/or changes to the product and/or specifications of the product described in this
manual, without prior notice. Antaira Technologies, LLC will not be liable for any technical inaccuracies or
typographical errors found in this guide. Changes are periodically made to the information contained herein and
will be incorporated into later versions of the manual. The information contained is subject to change without prior
notice.

Antaira Technologies - Industrial Ethernet Switches
LMX-0802 Series Hardware Manual V1.2
III
FCC Warning
This equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant to Part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy. It may cause
harmful interference to radio communications if the equipment is not installed and used in accordance with the
instructions. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the grantee of this device could void the user's
authority to operate the equipment.
CE Mark Warning
This is a Class-A product. In a domestic environment this product may cause radio interference in which case the
user may be required to take adequate measures.
Industrial Ethernet Switches
Industrial Grade Managed Ethernet Switches
Hardware Manual
Version 1.2 (March 2018)
This manual supports the following models:
 LMX-0802-M
 LMX-0802-M-T
 LMX-0802-S3
 LMX-0802-S3-T
 LMX-0802-ST-M
 LMX-0802-ST-M-T
 LMX-0802-ST-S3
 LMX-0802-ST-S3-T
This document is the current official release manual. Please check our website (www.antaira.com) for any
updated manual or contact us by e-mail ([email protected]).

Antaira Technologies - Industrial Ethernet Switches
LMX-0802 Series Hardware Manual V1.2
IV
Table of Contents
1. Introduction ................................................................. 1
1.1 Product Overview 1
1.2 Product Software Features 1
1.3 Product Hardware Features 2
1.4 Package Contents 3
1.5 Safety Precaution 3
2. Hardware Description ................................................. 4
2.1 Physical Dimensions 4
2.2 Front Panel 5
2.3 Top View 5
2.4 LED Indicators 7
2.5 Reset Button 7
2.6 Ethernet Ports 8
2.7 Fiber Port 9
2.8 Cabling 10
2.9 Wiring the Power Inputs 10
2.10 Wiring the Fault Alarm Contact 10
2.11 Grounding Note 11
3. Mounting Installation ................................................ 12
3.1 DIN-Rail Mounting 12
3.2 Wall Mounting 13
4. Hardware Installation ................................................ 14
4.1 Installation Steps 14
4.2 Maintenance and Service 14
5. Technical Specifications ........................................... 16

Antaira Technologies - Industrial Ethernet Switches
LMX-0802 Series Hardware Manual V1.2
1
1. Introduction
All Antaira industrial managed switches come with a pre-installed “user-friendly” web console
interface, which allows users to easily configure and manage the units, whether one is using a
serial console and command line interface (CLI) commands like Telnet, SSH, HTTP (Web GUI)
or simple network management protocols (SNMP).
1.1 Product Overview
Antaira Technologies’ LMX-0802 series is an 8-port industrial managed Ethernet switch that is
embedded with 6*10/100 Ethernet ports and 2*100Fx SC or ST type Fiber connectors to support
either multi-mode (2Km) or single-mode (30Km). It is a fully manageable Layer 2 Ethernet switch
that is pre-loaded with a user-friendly web management console design. It supports the ring
network redundancy function using the market’s open standard ITU-T G.8032 ERPS (Ethernet
Ring Protection Switch) protocol that has a <50ms network recovery time. The advanced network
filtering and security functions, such as, IGMP, VLAN, QoS, SNMP, port lock, RMON, Modbus
TCP, and 802.1X/HTTPS/SSH/SSL increase determinism and improve network management for
remote SCADA systems or control networks.
The LMX-0802 series is compact, IP30 rated, and DIN-rail or wall mountable. There are also two
different models for varying operating temperatures for either a standard temperature range (STD:
-10°C to 70°C) or an extended temperature range (EOT: -40°C to 75°C). It also provides high EFT
and ESD protection for industrial networking applications, such as, power/utility, water wastewater,
oil/gas/mining, factory automation, security surveillance, ITS and any other outdoor or harsh
environment.
1.2 Product Software Features
 Network Redundancy
 STP, RSTP, MSTP, ITU-T G.8032 Ethernet Ring Protection Switch (ERPS) for
network redundancy
 Network Management
 Web UI based management, SNMP v1/v2/v3, Serial Console
 Qos, traffic classification QoS, Cos, bandwidth control for Ingress and Egress,
broadcast storm control, Diffserv
 IEEE802.1q VLAN tagging, port-based VLAN support

Antaira Technologies - Industrial Ethernet Switches
LMX-0802 Series Hardware Manual V1.2
2
 IGMP snooping v1/v2, IGMP filtering / throttling, IGMP query up to 256 group
 Supports IPv4/IPv6, RMON, MIB II, port mirroring, event syslog, DNS, NTP/SNTP,
HTTPS, SSH/SSL, TFTP
 MODBUS TCP for SCADA system integration
 Port Configuration
 Status, statistics, mirroring, rate limiting, event syslog
 Event Handling
 Event notification by Email: Cold/Warm Start, Power Failure, Authentication,
SNMP trap and Fault Alarm Relay Output
 Software Upgrade via TFTP and HTTP
 Configuration Backup – USB Port
1.3 Product Hardware Features
 System Interface and Performance
 All RJ-45 ports support Auto MDI/MDI-X Function
 Embedded 6*10/100Tx Fast Ethernet RJ45 Ports, and 2*100Fx SC or ST type Fiber
connectors; Multi-mode 2Km, or Single-mode 30Km
 Store-and-forward switching architecture
 8K MAC address table
 Power line EFT protection: 2,000VDC; Ethernet ESD protection: 6,000VDC
 Power Input
 DC 12~48V redundant with a 6-pin removal terminal block
 One user programmable alarm relay contact
 The power input specification is complied with the requirements of SELV (Safety Extra Low
Voltage), and the power supply should be complied with UL 61010-1 & UL 61010-2-201
 Operating Temperature
 Standard operating temperature models: -10°C to 70°C
 Extended operating temperature models: -40°C to 75°C
 Case/Installation
 IP-30 protection metal housing
 DIN-Rail and wall mount design
 Installation in a Pollution Degree 2 industrial environment

Antaira Technologies - Industrial Ethernet Switches
LMX-0802 Series Hardware Manual V1.2
3
1.4 Package Contents

1– LMX-0802 series: 8-port industrial managed Ethernet switch, with 6*10/100Tx RJ45
Ethernet ports and 2*100Fx (SC/ST) Fiber Ports (Multi-mode 2Km, or Single-mode 30Km)


1-Product CD


DIN-Rail & 2-W all mounting brackets and screws


1-RJ45 to DB9 Serial Console cable


1-DC cable –18 AWG & DC jack 5.5x2.1mm

1.5 Safety Precaution
Attention: If the DC voltage is supplied by an external circuit, please use a
protection device on the power supply input. The industrial Ethernet
switch’s hardware specs, ports, cabling information, and wiring
installation will be described within this user manual.
Warning Labels
The caution label means that you should check the certain information on user manual when working with
the device. (Shown in Figure 1.1)
Figure 1.1 - Caution Label
This warning label is on the device, and means that the surface of the device is hot. (Shown in Figure 1.2)
Figure 1.2 - Hot Surface Warning Label

Antaira Technologies - Industrial Ethernet Switches
LMX-0802 Series Hardware Manual V1.2
4
2. Hardware Description
2.1 Physical Dimensions
Figure 2.1, below, shows the physical dimensions of Antaira’s LMX-0802 series: 8-port
industrial managed Ethernet switches with 6*10/100Tx ports and 2*100Fx fiber ports.
(W x D x H) is 54mm x 99mm x 142mm
Figure 2.1
LMX-0802 Series Physical Dimensions

Antaira Technologies - Industrial Ethernet Switches
LMX-0802 Series Hardware Manual V1.2
5
2.2 Front Panel
The front panel of the LMX-0802 series industrial managed Ethernet switch is shown below in
Figure 2.2.
6-Pin Removal Terminal Block (Power Input)
Grounding Screw
LED for PWR1, PWR2, and Fault
LAN Port #7~8 – 100Fx
Console Port
USB Backup
Hard (Physical) Reset Button
LAN Port (1~6) 10/100Tx
LED for 10/100Tx network speed Status
Figure 2.2
The Front Panel of LMX-0802 Series
2.3 Top View
Figure 2.3, below, shows the top panel of the LMX-0802 series switch that is equipped
with one 6-pin removal terminal block connector for dual DC power inputs 12~48VDC.
Figure 2.3
Top Panel View of LMX-0802 Series

Antaira Technologies - Industrial Ethernet Switches
LMX-0802 Series Hardware Manual V1.2
7
2.4 LED Indicators
There are LED light indicators located on the front panel of the industrial Ethernet switch
that display the power status and network status. Each LED indicator has a different color
and has its own specific meaning, see below in Table 2.1.
LED Color Description
P1 Green On Power input 1 is active
Off Power input 1 is inactive
P2 Green On Power input 2 is active
Off Power input 2 is inactive
Fault
Green/
Red
Green
Preconfigured alarms are not detecting failure.
Red Preconfigured alarms are detecting failure.
Off Switch is in the process of booting
Owner Green On ERPS Owner Mode (Ring Master) is ready
Off ERPS Owner Mode is not active
Ring Green On Ring Network is active
Off Ring Network is not active
LAN Port 1 ~ 4
(Left LED)
Green
On Connected to network, 100Mbps
Flashing
Networking is active
Off Not connected to network
LAN Port 1~ 4
(Right LED)
Green
On Networking is active, 10Mbps
Flashing Networking is active
Off Not connected to network
Fiber Port #7~8
LNK/ACT
Green
On Connected to network, 100Mpbs
Flashing Networking is active
Off Not connected to network
Table 2.1 - LED Indicators for LMX-0802 Series
Caution: "P1" is the abbreviation for "Power ", “P2” is for “Power 2”, “LNK” is for “Link”, and "ACT" is
for "Activity".
2.5 Reset Button
There is a ‘Reset’ button located on the front panel of the industrial Ethernet switch that helps
users to reboot, restore default, or save running configurations by pressing the button for
different seconds. Please refer to Table 2.2 for the timing and function.