ANTAIRA LMX-1802G-M12-10G-SFP-67-110 Series User manual

Antaira Technologies
LMX-1802G-M12-10G-SFP-67-110 Series
18-Port Industrial M12 IP67 Waterproof Gigabit Light Layer 3
Managed Ethernet Switch, with 16*10/100/1000Tx M12
Connectors (X-Coded) and 2*1G/10G SFP Slots,
24-110VDC Power Input
Quick Installation Guide
Version 1.0
(October 2021)
Tel: [phone]
Fax: [phone]
www.antaira.com
19020000000154
Package Check List
The package contains the following items:
 1 – Quick Installation Guide
 1 – LMX-1802G-M12-10G-SFP-67-110(-T)
 1 – Dust Cover Set
 2 – SFP Metal Field Installable Cable End Lock
 1 – SFP Removal Kit
Front Panel Layout
1 Power 1, Power 2, Status,
Master, Rin
g
7 DI/DO Port
2 Port 1~16 Link/Active Status
10/100/1000 Mbps 8 Power Input Port
3 Port 17~18 SFP Link/Active
Status 1G/10Gbps 9 1G/10G SFP+ Port
4 10/100/1000Base-T(X)
Ethernet Port 10 Mounting hole
5 Console Port 11 Grounding screw
6 USB Port
Product Overview
System Interface/Performance
 All Ethernet ports support the auto MDI/MDI-X function
 M12 connector with IP67 rated protection
 Store-and-forward switching architecture
Power Input & Connection
 DC 24 to 110V redundant power
 It is recommended to use a UL listed industrial power supply
Operating Temperature
 Standard operating temperature model: -10°C to 65°C
 Extended operating temperature model: -40°C to 70°C
Case/Installation
 IP67 protection
 Wall Mount design
LED Indicators
LED Color Description
P1 Green
On Power input 1 is active
Off Power input 1 is inactive
P2 Green
On Power input 2 is active
Off Power input 2 is inactive
Status
Green On No event happened after the last
reset or reboot
Red
On
1. System booting
2. Event happened by software
setting
Flashing Firmware Upgrade
Master Green
On ERPS Owner Mode (Ring Master) is
ready
Off ERPS Owner Mode is not active
Ring Green
On ERPS Ring Network is active and
work well
Flashing ERPS Ring works abnormally or
misconfigure
Off ERPS Ring Network is not active
LINK/ACT
(Port 1~16)
Green
On Connected to network, 1000 Mbps
Flashing Networking is active
Off Not connected to network
Amber
On Connected to network, 10/100 Mbps
Flashing Networking is active
Off Not connected to network
LINK/ACT
(SFP Port
17~18)
Green
On Connected to the network, 10Gbps
Flashing Networking is active
Off Not connected to network
Amber
On Connected to the network, 1Gbps
Flashing Networking is active
Off Not connected to network
8
24
9 3
1
7
6
5
10
11

Quick Installation
Ethernet Ports
M12 Ports (Auto MDI/MDI-X)
All M12 ports (8-Pin X-Coded Female Connector) are auto-sensing for
10Base-T, 100Base-TX, or 1000Base-T device connections. Please
follow the wiring pin assignment table below for Ethernet port installation.
Illustration Pinouts 10/100Base-T(X)
Signal
1000Base-T
Signal
1 Transmit Data + (TX+) BI_DA+
2 Transmit Data - (TX-) BI_DA-
3 Receive Data + (RX+) BI_DB+
4 Receive Data – (RX-) BI_DB-
5 BI_DD+
6 BI_DD-
7 BI_DC-
8 BI_DC+
NOTE: Recommended use the wire gauge between 18AWG.
Power Input Wiring
• Dual DC power inputs for power redundancy
• Connection format: M12 5-Pin K-Coded male connector
• Pin assignment of M12 power connector:
Illustration Pinouts Function
1 Power Input 1 + (V1+)
2 Power Input 1 - (V1-)
3 Power Input 2 - (V2-)
4 Power Input 2 + (V2+)
5 GND
NOTE: Recommended use the wire gauge between 24AWG.
Console Port
• Connection format: M12 5-Pin A-Coded Female Connector
• Baud rate 115,200bps, 8, N, 1
Illustration Pinouts Signal
1 NC
2 TX
3 RX
4 NC
5 GND
USB Port
• Connection format: M12 4-Pin A-Coded Female Connector
• USB Port is for configuration backup / restore
Illustration Pinouts Function
1 DN
2 VBUS
3 GND
4 DP
Relay Contact and Digital Input
• Connection format: M12 5-Pin A-Coded Male Connector
• Minimum Wire Gauge: 24AWG
Illustration Pinouts Function Function
1 DI+ Relay Com Common
2 DI+ Digital Input +
3 DI- Digital Input -
4 DI- Relay (N.C.) Normally Closed
5 NA Not Assigned
• Digital Input (DI)
The digital input is used for monitoring two external events via an
external voltage source. When the voltage level on digital input pins
changes from high voltage to low voltage, the DI function will be
triggered. Below table is shown a detail specification of the digital
input.
Specification Description
Level 0 (Low) -30~8VDC Will trigger DI function
(active trigger states)
Level 1 (High) 10~30VDC Normal Status
(inactive trigger states)
Nominal input voltage 24VDC
Max. input voltage 30VDC
Nominal input current 5mA (typical)
Max. input current 8mA
Reset to Default
Please perform the below steps to reset the switch to factory default
setting.
Step 1. Reverse the Tx & Rx of the Console Cable and plug it into the
console port.
Step 2. Restart the power.
Step 3. The switch will start rebooting with the port LEDs flashing.
Step 4. When the Status LED turns into Green, the process is
completed.
Step 5. Remove the reversed console cable.
Bypass Function
This Ethernet switch supports bypass function by two Ethernet ports (8
and 16). When one of the Ethernet switches loses power, Ethernet ports
(8 and 16) will bypass the power lost Ethernet switch to prevent the
network from disconnecting.
SFP Installation
Wall Mounting Installation
Follow the steps below to mount the switch to a wall using the screw
holes.
Step 1. Prepare 4 screws for mounting the switch to a wall.
(Recommended use the M5 screws.)
Step 2. Based on the positions of 4 screw holes on the left and
right side of the switch to make 4 screw holes on a wall
accordingly.
Step 3. Insert the screws through the screw holes on the switch
and screw the switch into the wall.
Step 4. To remove the switch from the wall, do the opposite from
the steps above.
Antaira’s Customer Service and Support
• Antaira’s Technical Service & Support Centers:
+ 844-268-2472 (Antaira US Headquarter)
+ 48-22-862-88-81 (Antaira Europe Office)
+ 886-2-2218-9733 (Antaira Asia Office)
• Antaira’s Web Sites & Repair/Support Emails:
www.antaira.com / [email protected]
www.antaira.eu / [email protected]
www.antaira.com.tw / [email protected]
*Any changes will be announced on the Antaira website.