ANTAIRA LNP-2602G-SFP Series User manual

Antaira Technologies
LNP-2602G-SFP Series
26-Port Industrial PoE+ Gigabit Unmanaged Ethernet Switch,
with 24*10/100/1000Tx (30W/Port) and 2* Gigabit Combo Ports
(2*10/100/1000Tx RJ45 and 2*100/1000 SFP Slots)
Quick Installation Guide
Version 1.0
(September 2022)
Tel: [phone]
Fax: [phone]
www.antaira.com
19020000000189
Package Check List
The package contains the following items:
 1 – Quick Installation Guide
 1 – LNP-2602G-SFP(-T)
 1 – Rack Mounting Brackets and Screws
 1 – Dust Cover Set
Front Panel Layout
Back Panel View
LNP-2602G-SFP series back panel is equipped with one 8-
connector redundant power inputs (48-55VDC) and one 2-pin
terminal block for relay output. 
Product Overview
System Interface/Performance
 RJ45 port supports the auto MDI/MDI-X function
 Embedded 24*10/100/1000Tx (30W/Port) RJ45 Ethernet
ports and 2*Gigabit combo ports (2*10/100/1000Tx RJ45
and 2*100/1000 SFP slots)
 Store-and-forward switching architecture
 8K MAC address table
 Jumbo frame supports up to 9.6Kbytes
Power Input & Connection
 DC 48-55VDC redundant power
 It is recommended to use a UL listed Industrial Power
Supply
Operating Temperature
 Standard Operating Temperature Model: -10°C to 70°C
 Extended Operating Temperature Model: -40°C to 75°C
Case/Installation
 IP40 Protection
 1U Rackmount Design
Safety Precaution
If the DC voltage is supplied by an external circuit, please use a
protection device on the power supply input.
LED Indicators
LED Color Description
P1 Green
On Power input 1 is active
Off Power input 1 is inactive
P2 Green
On Power input 2 is active
Off Power input 2 is inactive
FAULT Red
On Power input 1 or 2 is inactive
Off Power input 1 and 2 is active
Combo Port
SFP
LNK/ACT
(Port 25-26)
Green
On Connected to network, 1000Mbps
Flashing Networking is active
Off Not connected to network
Amber
On Connected to network, 100Mbps
Flashing Networking is active
Off Not connected to network
Combo Port
LAN
(Port 25-26)
Green On Connected to network, 1000Mbps
Flashing Networking is active
Off Not connected to network
Combo Port
LAN
(Port 25-26)
Green
On Connected to network, 10/100Mbps
Flashing Networking is active
Off Not connected to network
LNK/ACT
LAN Port 1-24
Green
On Connected to network,
10/100/1000Mbps
Flashing Networking is active
Off Not connected to network
PoE
LAN Port 1-24
Green On Supplying power to the powered-
device
Off Not connected to a powered-device
8-connector power input
Grounding Screw
LED for Power 1, Power 2, Fault
LAN# 1~24 LED for PoE Status
LAN# 1~24 LED for Link/Activity
Status 10/100/1000Tx LAN# 1~24 – 10/100/1000Tx
RJ45 Ports
LED for SFP Link/Activity
Status
100/1000Mbps
Relay Output
Combo Port# 25~26 –
100/1000Fx SFP and
10/100/1000Tx RJ45

Quick Installation
Ethernet RJ45 Port (Auto MDI/MDIX)
RJ45 port is auto-sensing for 10Base-T, 100Base-TX or
1000Base-TX device connections. Please follow the wiring pin
assignment table below for the Ethernet port installation.
RJ45 Ethernet Port Pin Outs
Pins T568A Color T568B Color 10/100
Base-T(X)
1000
Base-T
1 White/Green White/Orang Rx+ TP0+
2 Green Orange Rx- TP0-
3 White/Orang White/Green Tx+ TP1+
4 Blue Blue unused TP2+
5 White/Blue White/Blue unused TP2-
6 Orange Green Tx- TP1-
7 White/Brown White/Brown unused TP3+
8 Brown Brown unused TP3-
SFP Slots
The Small Form-Factor Pluggable (SFP) is a compact optical
transceiver used in optical communications.
Please follow the steps below for connecting the SFP and LC
cable:
1. Insert the SFP transceiver module into the SFP slot as
shown below in Figure 1 (Please be noted that the triangle
mark is at the bottom of the SFP slot). Figure 2 shows the
SFP transceiver module was inserted.
Figure 1 Figure 2
2. Insert the fiber cable of the LC connector into the
transceiver as shown below in Figure 3.
Figure 3
Power Inputs Wiring
Please follow the below steps to insert the power wire:
1. Insert the positive and negative wires into the PWR1 (V1+,
V1-) and PWR2 (V2+, V2-) contacts on the terminal block
connector. See Figure 4.
2. Tighten the wire-clamp screws to prevent the wires from
loosening.
Figure 4
Industrial Switch Mounting
The switch comes with a rack-mounted kit can be mounted in an
EIA standard size, 19-inch rack. It can be placed in a wiring
closet with other equipment.
Perform the following steps to rack-mount the switch.
1. Position one plate to align with the holes on one side of the
hub and secure it with the smaller plate screws. Then, attach the
remaining plate to the other side of the switch.
2. After attaching both
mounting plates, position
the switch in the rack by
lining up the holes in the
plates with the appropriate holes on the rack. Secure the switch
to the rack with a screwdriver and the rack-mounting screws.
*Note: For proper ventilation, allow at least 4 inches (10 cm) of
clearance on the front and 3.4 inches (8 cm) on the back of the
switch. This is especially important for enclosed rack installation.
Field Maintenance and Service
 If the device requires servicing of any kind, the user is
required to disconnect and remove it from its mounting. The
initial installation should be done in a way that makes this as
convenient as possible.
 Voltage/Power lines should be properly insulated as well as
other cables. Be careful when handling them so as to not trip
over it.
 Do not under any circumstance insert foreign objects of any
kind into the heat dissipation holes located in the different
faces of the device. This may not only harm the internal
layout, but might cause harm to user as well.
 Do not under any circumstance open the device for any
reason. Please contact your dealer for any repair needed or
follow the instructions within the manual.
Warranty Policy
Warranty Conditions
Products supplied by Antaira Technologies are covered in this
warranty for sub-standard performance or defective
workmanship. The warranty is not, however, extended to
goods damaged in the following circumstances:
(a) Excessive forces or impacts
(b) War or an Act of God: wind storm, fire, flood, electric
shock, earthquake
(c) Use of unqualified power supply, connectors, or
unauthorized parts/kits
(d) Replacement with unauthorized parts
RMA and Shipping Costs Reimbursement
Customers shall always obtain an authorized "RMA" number
from Antaira before shipping the goods for repair or
replacement.
 Within the warranty period (based on the invoice date), all
parts and labor are free of charge to the customers.
 Customers are required to be responsible for the cost of
parts and labor, if the products are out of warranty.
 For RMA service, customers are responsible for the
shipping expense for shipping the RMA unit(s) to Antaira;
and Antaira will be responsible for the shipping expense by
ground service for the return repair/replace unit(s) back to
customers.
Limited Liability
Antaira would not be held responsible for any consequential
losses from using Antaira’s product.
Warranty Period
5-Year Warranty
Antaira’s Customer Service and Support
 Antaira’s Technical Service & Support Centers:
+ 844-268-2472 (Antaira US Headquarter)
+ 48-22-862-88-81 (Antaira Europe Office)
+ 886-2-2218-9733 (Antaira Asia Office)
 Antaira’s Web Sites & Repair/Support Emails:
www.antaira.com / [email protected]
www.antaira.eu / [email protected]
www.antaira.com.tw / [e-mail]
*Any changes will be announced on the Antaira website.