Anthro TECHNOLOGY FURNITUR SEC24 Series User manual

TECHNOLOGY FURNITURE®
Security Cart 24" Wide
Assembly Instructions
01– Shelf Clamp ...................................Qty. 4 .........................175-5059-00
02– Shelf Support........................ Qty. 4 .........................175-5060-00
03– Clamp Screw.............................. Qty. 4 .................. 325-5086-00
04– Door............................................ Qty. 1 ................. 835-5040-00
05– 30" Vertical Legs ................... Qty. 4 .........................125-5267-00
06– 1.5" End Cap .............................. Qty. 4 .........................175-5020-00
07– Side Panel X ......................... Qty. 1 ........................225-5948-00
08– 24" Wide Shelf ......................... Qty. 1 .........................100-6512-00
09– Panel Hanger ....................... Qty. 2 .........................225-5950-00
10– Panel Screw ................................ Qty. 4 .........................325-5196-00
11– Back Panel................................... Qty. 1 .........................225-5941-00
12– Cap Screw .................................. Qty. 32.......................325-5188-00
13– 5" Rhombus Casters ................. ........................................ (see below)
Swivel Lock Caster................... Qty. 2 .........................150-5080-00
Total Lock Caster ..................... Qty. 2 .........................150-5081-00
14– Lock Nut..................................... Qty. 16.......................325-5263-00
15– Caster Mount Bracket........... Qty. 4 ...........225-0585-04-02-00
16– 3/4" Wood Screw ..................... Qty. 12.......................325-5106-00
17– Funnel Head Screw................... Qty. 4 .........................325-5245-00
18– Corner Bumper......................... Qty. 4 .........................175-5112-00
19– Support Screw........................... Qty. 12.......................325-5010-00
20– Side Panel Y .......................... Qty. 1 .........................225-5949-00
21– Metal Base ........................... Qty. 1 .........................225-5943-00
All Screw quantities listed here are the minimum needed
for your Cart assembly. There may be a few extra Screws
included, which are not counted in the Parts List.
Anthro® Corporation Technology Furniture®10450 SW Manhasset Drive Tualatin, Oregon 97062
SAVE THESE INSTRUCTIONS! 1-800-325-3841
June 2006 Rev C
Questions? 1-800-325-3841
Enclosed Parts List
Detailed views of all Hardware is provided with each Assembly Step.
These Assembly Instructions
are for the SEC24xx/xx.
Before beginning assembly of your
Security Cart, please take a moment to
review the parts listed below to verify
that your shipment is complete.
It may also be helpful to review
the Assembly Instructions of all
Anthro Products you purchased
and are planning to include in
this installation.
To make the assembly of your Security
Cart even easier, we have included all of
the required tools. The handy Hex Driver
Bit can be used in your electric drill in
place of the Hex Driver.
Hex Driver 5/32" .......375-5000-00
3-Way Wrench ...........225-5196-00
Hex Key 3/16" ............375-5028-00
NOTE: When using a power drill
during assembly,ALWAYS begin
threading fasteners by hand!
01 02
03
04
05
06
07
17
16
10
15
09
11
12
13
14
18
08
21
19 20
Panel Screw
Step 9
Rotate your Cart upright.
Facing the rear of the Cart, orient the Back Panel so the
tabs are towards the bottom.
Carefully insert the two small tabs at the bottom of the
Back Panel into the slots on the Metal base. Tilt the top of
the Back Panel towards the Cart to meet the Panel Hang-
ers. Secure using two Panel Screws.
Panel Screw
325-5196-00
Back Panel
Step 8
Place the Metal Base Assembly onto the legs. Check the
orientation of the Base Assembly. Casters with the Green
Brake Pedals should face either the left or the right. Also,
the slots on the metal base (used for installing the Back Panel)
should align with the Panel Hangers on the wood shelf.
Align Vertical Legs with corner holes in the Base Assembly.
Insert a Funnel Head Screw through the Base and carefully
thread into the Leg.
Repeat for other three corners and tighten all screws.
Funnel Head Screw
325-5245-00
Funnel Head
Screw
Base Assembly
Step 11
Pop the 1.5" End Caps into the tops of the Legs.
Congratulations! Your assembly is complete.
1.5" End Cap
Back Panel
Mount Detail
Tabs
Step 10
Orient the Door so that the Lock Assembly is at the top.
With the Door in the open position (as shown), align the
pins on the Door Hinges with the Hinges on the Cart
and slide down into place.
Door
Lock Assembly
Hinge Attachment
Detail
(Green Brake Pedal)

Anthro® Corporation Technology Furniture®10450 SW Manhasset Drive Tualatin, Oregon 97062 www.anthro.com
Nylon Lock Nut
325-5263-00
Cap Screw
325-5188-00
Step 1
Secure a Caster to a Caster Plate using four 3/4" Cap Screws
and Lock Nuts per Caster.
Repeat for remaining Casters, Caster Plates, Bolts, and Nuts.
Inside Edge
(Green Brake Pedal)
Cap Screw
Lock Nut
Cap Screw
325-5188-00
Step 2
Place the Caster Plates with the Green Brake Pedals onto one
side of the Metal Base, sliding each Plate under the anges on
the Metal Base. Secure using four Cap Screws.
Install the remaining Caster Plates on the other side.
Double-check the installation of the Swivel Lock Casters
(green brake pedal) by positioning the Caster Plates as shown.
Now depress the Brake. If it is installed correctly, the
Caster will be parallel with the Metal Base (as shown).
3/4" Wood Screw
325-5106-00
Caster Bracket is
positioned BELOW
the ange
Metal Base
ange
Rear Edge of
Metal Base has
four small holes
along edge.
Swivel Lock Casters
(Green Brake Pedal)
Swivel Lock Casters
(Green Brake Pedal)
Base Assembly
First
Next
Final
Barbs
Cart Assembly
Step 5
Loosely attach the 24" Wide Shelf to the second hole from the
top (uncapped end) of each Vertical Leg using a Support Screw.
Next, align the two openings on each of the Panel Hangers with
those on the Shelf. Secure into place using two Wood Screws
through the Bracket into the Shelf.
Repeat for other Panel Hanger.
Wood Screw
Support Screw
325-5010-00
3/4" Wood Screw
325-5106-00 Support Screw
24" Wide Shelf
Vertical Legs
Step 6
Align one vertical leg so that the end with the Star Nut
inside is facing up. Loosely attach the 24" Wide Shelf to
the second hole down using a Support Screw.
Next, align each Panel Hanger with the pre-drilled holes
on the shelf. Secure in place using two Wood Screws.
Support Screw
325-5010-00
3/4" Wood Screw
325-5106-00
Side Panel Y
Support Screw
Vertical Leg
24" Wide Shelf
Side Panel X
Support Screw
Support Screw
325-5010-00
3/4" Wood Screw
325-5106-00
Wood Screw
24" Wide Shelf
Step 7
Install the Side Panel X (with hinges) using the same
procedure described in Step 6.
Repeat for Side Panel X (with hinges).
Cap Screw
Panel Hanger
Wood Screw
Step 3
Slide the Plastic Corners between the Metal Base and
Caster Plates, securing with one 3/4" Wood Screw
through each Bracket into the Plastic Corners.
Hollow side
face up
Wood Screw
Step 4
Attach four Shelf Supports to the Top Shelf. Begin by rst
installing a Clamp into the Shelf notch. Be sure the pointed
Barbs face towards the outer Shelf edge.
Next slide a Shelf Support into the recesses of
the Clamp and Shelf. Push in as far as possible.
Finally, secure with a Clamp Screw
Clamp Screw
325-5086-00