Anzzi SD-AZ01-01 User manual

Models:
SD-AZ01-01
ANZZI GLASS SHOWER DOOR
INSTALL GUIDE
Have questions? Call us at 1-844-44-ANZZI or
email at [email protected].

Notice:This assembly requires two people due to the weight of the
glass doors. Professional installers are highly recommended.
1. Carefully inspect all boxes and packages to make sure no damage
occurred during shipping. If you find a unit has been damaged, is missing
parts, or has finishing defects, contact our customer support department
within 5 business days of the delivery date. Note: After 5 business days,
or if the product has been already installed, we will not replace any miss-
ing parts or damaged products.
Once all boxes and packages are inspected and opened, thoroughly read
through this instruction manual. Take time to view the “Detailed Diagram
of Shower Door Components” page and mark each piece as you ensure
all necessary parts required for assembly are included in the package.
2. Note: Keep in mind that we are not responsible for code compliance
standards for your project and we will not accept any returns. Plumbing
and building codes differ from one location to another, so it is crucial to
review your local building codes before installation to help answer any
questions you have about installation compliance standards.
3. Make sure the installation surface area is level, solid, and can sup-
port the entire weight of the unit and the walls are at right angles before
beginning installation. Major problems may occur if the surface area
isn’t level and side wall angles are abnormal. It is recommended that all
primary surfaces of the unit be protected during installation. Leveling
adjustments and drilling may be necessary depending on the unit being
installed.
4. Finished floor and walls are required for installation of this unit.
5. IMPORTANT: Each side of this door features a 1” out-of-plumb ad-
justment. Ensure your shower base or threshold is leveled and walls are
vertical.
Note: Be sure the CLEAR side of the glass with print, molded, or silk
designs faces the interior of the shower.
ATTENTION: Use caution when unpacking and inspecting your unit. For
easy part identification, refer to the detailed diagram in your manual and
lay out each piece accordingly. Do NOT discard cartons and hardware
bags until you have thoroughly checked for all parts. Contact us regarding
any missing or damaged parts.
NOTE: Keep these instructions for installation to refer to later.
GETTING STARTED

1. (2x) Glass
2. (2x) Guide rail
3. (1x) Fixed glass profile
4. (2x) Wall profile
5. (2x) Glass panel
6. (1x) Glass door
7. (2x) Water proof strip
8. (3x) U-Strip
9. (1x) Magnetic strip
10. (1x) Handle
11. (2x) Top side wheels
12. (2x) Bottom side wheels
13. (16x) Screw ST4* 30
14. (8x) Wall anchor
15. (4x) Screw ST4* 12
16. (4x) Glass holder
Tape Measure, Pencil, Phillips Screwdriver
Drill Bits D=5/16” and D=1/8”
Level, Caulking Gun, Electric Drill, Hammer
PARTS LIST
TOOLS YOU’LL NEED
1
2
3
4
5
6
78
9
10
11
12
13

1. Use the Round Head Screws ST4x30 (13) to attach the bottom Guide
Rail (03) to the Glass Profiles (02).
2. Affix the U Shape Strip (08) to the stationary glass. Install the Stationary
Glasses (05) by fully sliding one into the groove of the Glass Profiles (01).
Securely fasten it near the Glass Holders (16) to the bottom Guide Rail
(02). To install the second stationary glass into the groove of the Glass
Profiles (01) repeat this step.
TUB DOOR

NOTE: Avoid scratching or damaging the aluminum and glass by refraining from using a screwdriver or other metal device.
3. For your convenience, the Stationary Glasses Profile (magnetic) (03) has already been assembled.
Refer to Figure 4 for details.
4. Fit the Anti-Water Strip (07) into the Stationary Glasses (05).
Refer to Figure 5 for details.
5. Insert the Wall Profiles (04) by carefully sliding them onto the Glass Profiles (01) on both sides. Ensure the Wall Profiles flanges face the interior of the
shower.
U-STRIPS
A
DETAIL A

6. Place the completed frame on the shower base, threshold, or bathtub in its designated position. Carefully push the frame against the walls. Sometimes
the upper and lower wall opening measurements differ or the walls may not be plumb. To fix this problem, make slight adjustments by gently pulling the
Wall Profiles (04) out of the Glass Profiles (01) and use a leveler tool to adjust the vertically positioned frame.
7. This step will require an assistant to help hold the assembly in the proper position while drill holes are marked on the wall through the holes found on
the Wall Profiles (04) flange.
Carefully set the assembled unit to the side. Using a Ø 5/16” drill bit, drill the holes and insert the Wall Anchors (14). Add silicone caulk around the holes
in the wall, along the Wall Profiles, and under the bottom Guide Rail (02). Reposition the entire shower assembly back into its designated location and use
the Round Head Screws ST4x30 (14) to secure it to the walls.
U-STRIPS

6. Place the completed frame on the shower base, threshold, or bathtub in its designated position. Carefully push the frame against the walls. Sometimes
the upper and lower wall opening measurements differ or the walls may not be plumb. To fix this problem, make slight adjustments by gently pulling the
Wall Profiles (04) out of the Glass Profiles (01) and use a leveler tool to adjust the vertically positioned frame.
7. This step will require an assistant to help hold the assembly in the proper position while drill holes are marked on the wall through the holes found on
the Wall Profiles (04) flange.
Carefully set the assembled unit to the side. Using a Ø 5/16” drill bit, drill the holes and insert the Wall Anchors (14). Add silicone caulk around the holes
in the wall, along the Wall Profiles, and under the bottom Guide Rail (02). Reposition the entire shower assembly back into its designated location and use
the Round Head Screws ST4x30 (14) to secure it to the walls.
DRILLING
Mark these
holes on wall

8. Adhere the top and bottom Wheels (11) & (12) to the Glass Door (06). The upper wheels have an adjustable bolt and lock nut that can alter the door level
as necessary. The lower wheel features a press that works to secure the wheel to the bottom Guide Rail (02).
NOTE: When installed, the upper wheel lock nut and lower wheel press button should be pointing upwards.
Refer to Figure 10 for details.
9. Position the top door wheels into the top Guide Rail (02) using a sliding motion. Adjoin the bottom wheels and the Guide Rail by pushing the bottom
wheels into the bottom rail and pressing down the button located on the Wheel Assembly.
NOTE: DO NOT use a power screwdriver for adjustments. Adjust the upper wheels using the Phillips screwdriver until they glide smoothly, and the door
tightly closes.
DRILLING
Ø6
A
DETAIL A

10. Affix the Handles (10) to the Glass Door (06). Place the Anti-Water Strips
(07) firmly on the vertical edges of the Stationary Glass and the Glass Door.
For a tight close, secure the Magnetic Strip (09) on the vertical edges of the
Glass Door.
11. Make any final adjustments to the assembled unit in the Wall Profiles (04)
before using a Ø 1/8” drill bit to drill holes in the Wall Profile and Glass Profile
(01).
NOTICE: Only drill the first layer of the wall profile and glass profile. Do NOT
drill the profiles throughout.
Use the Round Head Screws ST4x12 (15) to affix the Wall Profile to the Glass
Profile. Use the Decorative Covers (15) to cover the visible screw heads.
12. Carefully add the sealant along the guide rails and profiles, along the
shower base or threshold, and on the seams between the profiles and lower
guide rail.
WARNING: WAIT 24 HOURS BEFORE USING THE SHOWER
ENCLOSURE TO ALLOW THE SILICONE GEL TO DRY COMPLETELY.
HARDWARE

Guarantee a longer life of the hardware finish by wiping off the metal
parts with a soft cloth after each use. Avoid using abrasive cleaners and
products especially those that contain bleach, acid, or ammonia. In the
case that these chemicals are used, thoroughly rinse the surface as soon
as possible and wipe dry with a soft cloth. Stainless-steel surfaces should
be cleaned once a week or as needed. When applying a stainless-steel
polish or cleaner, work with the grain and not against it. Avoid the use
of abrasive tools such as wired brushes, abrasive cloths or sponges, or
steel wool.
Tempered Glass: Nonabrasive bathroom cleaners and your usual glass
cleaner may be used to clean tempered glass. Be sure to thoroughly
rinse off any cleaner. Do NOT strike the glass with any hard or sharp
object as it could can cause immediate damage or cause the glass to
eventually break.
Wheel Maintenance: To keep the roller movement smooth, apply a small
amount of lubricating oil. Periodically adjust the wheel screw to ensure
the moving door slides smoothly and the bearing functions effectively.
MAINTENANCE