Anzzi Sifo KF-AZ301 Series User manual

ITEM: KF-AZ301**
INSTALL & OPERATION MANUAL
V1.0
ANZZI SENSOR KITCHEN FAUCET
DON’T WAIT!
REGISTER NOW!
Register your product within 90 days to ensure your product is
recognized as an purchase and is for warranty
coverage.
in the registry card (Pg. 2) or register
at www.swcorp.com/register
.
LEAD FREE
NSF/ANSI/CAN 61

Have questions? Call us at 305-614-4070 or visit us at www.ANZZI.com

[270mm]
10.6"
[174mm]
6.85"
[101mm]
3.97"
[210mm]
8.26"
[227mm]
8.93"
[65mm]
2.55"
12°
[440mm]
[40mm]
MAX 1.57"
17.32"
[58mm]
2.28"
9/16-24UNEF
3.13"
[79.5mm]
Ø1.18"
[30mm]
24.8"
[630mm]
Ø1.25"
[32mm]
PRODUCT SIZE CHART
PG.1
TOOLS AND MATERIALS
Wrench Screwdriver
Marker Pen Drilll
Ø 1/4"
(6mm)
Drill bit
SILICONE
Bucket

PG.2
01
02
03
04
06
10 11 12 13
14
15
07
08
09
18
16
COMPONENTS
Part Discription Qty.
Screw
[ 01 ]
Nut
Metal gasket
[ 02 ]
[ 03 ]
[ 04 ]
[ 05 ]
[ 06 ]
[ 07 ]
[ 08 ]
[ 09 ]
[ 10 ]
[ 11 ]
Rubber gasket
Faucet
Deck plate
Washer
[ 12 ]
[ 13 ]
[ 14 ]
[ 15 ]
[ 16 ]
[ 17 ]
[ 18 ]
Sprayer
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
17
Before installation:
1. Please check that all components are present.
2. Ensure that all supply lines are free of debris with supply stops installed.
3. Ensure water pressure is between 20-125 PSI.
4. If you are having difficuties on installation, please contact a professional plumber.
05
Bend
Cartridge
Locking nut
Cap
Handle
Cap
Screw
Control box
Clip
Weight
[ 19 ] Hose
19
1

INSTALLATION
rubber
washer
Deck plate
01 SINGLE HOLE THREE HOLES STEP 1:
Single hole application: Install Faucet[07]
and Rubber Washer[06] in hole on sink.
Three holes application: Install Faucet[07]
through Deck Plate[05] in hole on sink. Align
the Deck Plate[05] to the grooves of
Faucet[07] .
Note: Installs with handle on right side only
for both applications.
2.1 2.2
STEP 2:
2.1 Slide Rubber Gasket[04] and Metal
Gasket[03] up onto Faucet[07] under sink
and secure with Nut[02].
1. L ocate the control box under the sink.
2. Mark the secure holes of the control box by
pen.
the lowest
location lf
the of hose
24.6"(625mm)
9.8"(250mm)
11.8"(300mm)
02
03 04
Note: Make sure the control box pointed
upward as the label on it indicates.
If screw locations are not in stud. Drill three
0.24’’(6mm) diameter holes on the wall.
Insert the plastic anchors into the holes and
drive screws into the anchors. If screw
locations are in wall stud, drive screws directly
into stud.
STEP 3: STEP 4:
2.2 Hand tighten the Nut[02] and tighten the
screws[01] by screwdriver to secure the faucet.
PG.3

PG.4
INSTALLATION
outlet connection
screw
mounting slot
safety tab
STEP 5:
1. Place Control Box on wall and slide
onto mounting slot.
2. Secure Control Box to wall with screw
through safety tab.
STEP 6:
6.1 6.2
STEP 7:
05
06
07
6.1 Connect the outlet hose (the
shortest one) to the connecting
end on top of the control box.
Push in until a “click” is heard.
Tug the outlet hose upward to
test engagement, ensure it’s
connected firmly.
6.2 Connect the hose (the longest
one) to the connecting end on
bottom of the control box. Push
in until a “click” is heard.Tug the
hose downward to test
engagement, ensure it’s connected
firmly.
Make sure all fittings and end connections are free of
debris.Turn off the supply valves(not provided). Connect
faucet supply hoses to the supply valves, making sure the
red braided hose with “HOT” label connected to the hot
supply valve and the blue braided hose with “COLD” label
connected to the cold supply valve, hand tighten them,
then tighten with wrench for three quarters or one turn.
DO NOT OVERTIGHTEN.
WARNING: Do not use pipe dope or other sealants on
water connections.

8.1 8.2 STEP 8:
8.1 Connect the cable of Faucet[07] to
the cable of Control Box[16] with t
he
matching direction. Secure the
connection by turning the nut of the
Control Box[16] cable.
8.2 Tie the cable to the outlet hose with
a cable tie.
Note: DO NOT tie the HOSE[19].
STEP 9:
Remove the screws of the Weight[18] and
install the Weight[18] to the hose[19] where
the weight label located and secure it by
tightening the screws.
PG.5
thin pin
thick pin
Weight location
label
STEP 10:
INSTALLATION
battery box
10
08
09
1. Remove the battery box from the bottom of
Control Box[16].
2. Install 4 AA batteries(not provided) to the
battery box and push it back into the
control box.
Notice:
a. Make sure the battery polarities match.
b. Don't mix old and new batteries.
c. Do not mix alkaline, standard (carbon zinc)
or rechargeable (nickel cadmium, nickel
manganese) batteries.
e. Do not throw away used batteries into the
garbage. Please properly dispose of all used
batteries in accordance to your local codes
and laws.”

PG.6
STEP 11:
Attach and secure the Sprayer[09] onto the
Hose[19] .
STEP 12:
Turn on hot and cold water supplies and
check all connections at arrows for leaks.
Retighten if necessary, but do not
overtighten.
STEP 13:
Handle
INSTALLATION
13
11
12
Open the handle and wave your hand over the
sensor within 7cm distance to start the flow of
water. Set the water temperature using the handle.
Let the water flow and check all connections at
arrows for any leaks. The water flow will
automatically stop in 3 minutes.
Notice:
a. Please keep the sensor window clean.
b.
Please replace the batteries as soon as possible.
Sensor
window
When the battery is low, the sensor window will
flash twice per second until battery runs out.
c. When the batteries have run out and new
replacement batteries are not available, please
switch the control box to manual operation by
following the instructions on PG.7.”

SPRAYER FUNCTIONS.
Clip
MANUAL OPERATION.
1. Remove the Clip from the control box.
PG.7
handle
OPERATION
1
2
3
Button 1: Enhanced fan-shaped spray mode
(Powerful spray, more convenient for washing
dishes. Performance will be subject to water
pressure, work at its best when water pressure
above 30 psi. )
Button 2: Standard flow of aerator
Button 3: Standard spray mode
Note: 3-function Sprayer will return to position
2 automatically if left in position 1 or position
3 when the faucet is turned off.
2. Turn the handle counter-clockwise for two
turns to disable the sensor control and switch
to a manually operated mode. In manual
operation the water flow is fully controlled using
the handle like any standard faucet.
3. Turn the handle clockwise until it stops and
insert the Clip back to lock the handle to switch
back to the sensor control mode.
1. Any leaks or damage may occur due to improper installation. Follow all instructions before making
any final connections and turning on water supplies.
2. When exiting the home make sure to close the faucet handle.
3. When leaving home or not using the faucet for an extended period of time please take the following
actions:
a. Close all water supply lines for the faucet.
b. Remove the batteries from the control box.
Notice:

filter
adapter
PG.8
CLEANING & MAINTENANCE
1. To preserve the finish on the metallic parts of your ANZZI faucet, apply non-abrasive wax, such as
car wax. Any cleaners should be rinsed off immediately.
2. Clean the aerator regularly for calcium build up or any blockage that reducing water flow.
Caution: Check all connections for leaks. Retighten if
necessary, but do not overtighten.
3.1 3.2
4. If the problem cannot be solved by measures at above
point 3, please clean the filter at the control box.
a. Turn off the handle and disconnect the outlet
hose from the control box.
b. Remove the adapter from the control box.
c. Clean the filter with brush and clean water only.
d. Install the filter and adapter back to the control
box and tighten. DO NOT OVER TIGHTEN.
e. Connect the outlet hose to the control box.Tug
the outlet hose upward to test engagement.
3. If the water flow lower than normal, please clean the filter at the inlet hoses.
a. Remove the hot and cold supply hoses (Fig 3.1).
b. Insert each hose into a cup of clean water and agitate it back and forth for 15 seconds to
remove any possible debris. Take out the hose from cup and drain (Fig 3.2).
c. Connect the supply hoses back to the supply valves. Tighten the nuts of the supply hoses
but do not over tighten.
d. Turn on hot and cold water supplies and check all connections for leaks. Retighten if necessary,
but do not overtighten.