Anzzi Mezzo Series User manual

INSTALL GUIDE
Model#
SH-AZ037
SH-AZ038
SH-AZ039
MEZZO SERIES
PERFECTION IS OUR TRADITION™
v2.0516

Parts List Pg. 1
Before You Start Pg. 2
Spec Drawing Pg. 3
Installation Pg. 4
Care & Maintenance Pg. 11
Warranty Pg. 12
Registration Final Page
TABLE OF CONTENTS
YOUR REVIEWS MATTER!
For more information please call 1-844-44-ANZZI
or email us at [email protected]
The ANZZI™ Family thanks you for your purchase and hopes you enjoy your very own ANZZI
product for years to come! In the meantime let us know about your experience? We would love
to hear your thoughts from the packaging to the quality and function of the product.
Leave a review on www.ANZZI.com/reviews and let everyone know how satisfied you are with
ANZZI!
Also, we humbly request submitting as many pictures as possible along with your review.
Millions of shoppers will want to know about your experience with our products. Don’t just tell
but show, too!

PARTS LIST
PERFECTION IS OUR TRADITION™
pg. 1
ASME A112.18.1/CSA B125.1
Shower arm
Flange
Shower head
Sleeve
Cartridge
Cartridge locknut
Trim cap
Body
Check valve
Joint
Joint
Index
Allen key
O-ring
Button
Screw
Handle
Ttrim plate
Protect cover
Screw
Screw
14
PART NAME
NO .
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Screw
1
2
3
4
5
6
789
10
11
12
13
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30 31
Connector
O-ring
Screw
23
24
25
26
27
28
29
30
Spout
31
Knob
Joint
Aerator wrench
O-ring
Aerator

PERFECTION IS OUR TRADITION™
pg. 2
For any questions or concerns contact
our dedicated technical support team
at 1-844-44-ANZZI.
BEFORE YOU START
Screwdriver Channel Locks
Adjustable Wrench Allen key
Goggles
Teflon tape
Recommended Items
ATTENTION: Please read all instructions thoroughly
including all warnings, attentions and notes before
beginning installation.

PERFECTION IS OUR TRADITION™
pg. 3
SPEC
DRAWING
mm
[inches]

Figure 1
INSTALLATION
PERFECTION IS OUR TRADITION™
pg. 4
Remove the protective covers (5a) and (5b) by turning counter clockwise and sliding them out.
Do not remove protective cover (5c) until you make sure the cover is flush with the finished
wall.
Using a Philips screwdriver, unscrew and remove the two screws (4).
Now remove the remaining protective cover (5c).
Step 1A
Step 1B
Step 1C
Step 1D
5a
5c
5b
4

Figure 2
INSTALLATION
PERFECTION IS OUR TRADITION™
pg. 5
Connect all plumbing lines to the faucet valve as shown.
Make sure the hot and cold supply lines are connected to the pertaining sides.
Step 2A
Step 2B

Figure 3
INSTALLATION
PERFECTION IS OUR TRADITION™
pg. 6
Turn on water and allow it to run for 1-2 minutes.
Check all connections and confirm there are no leaks before proceeding.
Step 3A
Step 3B

Figure 4
INSTALLATION
PERFECTION IS OUR TRADITION™
pg. 7
Apply Teflon tape to the shower arm (#2) then place shower arm flange (#1) on shower pipe
and screw shower arm to the pipe.
After shower arm is in place screw the shower head (#3) onto the arm.
Make sure the O-ring is placed in between the shower arm (#2) and the shower
head (#3).
Step 4A
Step 4B
Important:
O-ri ng
3
2
1
12
13
14
15
24
19
28
29
31
O-ring
3
2
1

Figure 5
INSTALLATION
PERFECTION IS OUR TRADITION™
pg. 8
Put the trim plate (#12) through the faucet valve then fasten it with screws (#19) and tighten
using screw driver.
Attach the diverter knob (#13) to the valve.
Place the mixing valve handle (#14) and secure with set screw (#15).
Finally, insert the index (#23).
Step 5A
Step 5B
Step 5C
Step 5D
O-ri ng
3
2
1
12
13
14
15
24
19
28
29
31
12
13
14
15
24
19