Anzzi FR-AZ174 User manual

RECOMMENDED TOOLS
EXPLODED DRAWING
Notes For reference only. We reserve the right
to make changes without any notice.
:
Please read the followings before installing and usage.
[inch]For Reference only (unit = mm )
DIMENSIONS
FAUCET MAINTENANCE
CARE INSTRUCTIONS
To keep your faucet looking its best, please follow
these simple care instructions:
1. Remove as much surface dirt and film using
clear water and a soft cotton cloth.
2. Use any of the following to remove tough
surface film and build-up:
- Mild liquid detergent
- Non-acidic, non-abrasive gentle liquid cleanser
- Non-abrasive liquid polisher.
3. Once clean, rinse faucet with clear water to
thoroughly remove cleaner or polish and blot
dry with soft cotton cloth.
1. Use abrasive cleansers, cloths, or paper towels.
2. Use any cleaning agents containing acids, polish,
waxes, alcohol, ammonia, bleach, solvents or any
other corrosive or harsh chemical cleansers.
NO.
Part No Qty
CTHZ0341
CTWP0207
CTCZ0224
CTWP0208
CTMB0675
CTWT0009
CTST0050
CTNB0325
CTWL0002
CTWR0347
CTDT0002
CTWQ0006
CTNP0045-XD
ATBQ2003
ATBP0313
CTST4101
CTFB0241
CTMB0588
CTST0153
CTWB0048
CTRR0138
CTRR0137
CTDB0131
CTWR0060
CTRR0082
CTPB0468
CTRP0067
CTBT0077
CTMB0593
CTDB0133
CTRR0139
CTWR0217
CTWT0038
CTNB0156
CTPB0188
CTNP0045-XR
ATBQ2002
ATBE0210
ATBD0080
ATBP0070
ATBA0100
ATBP0071
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
21
41
42
2
2
2
2
2
2
2
2
2
2
2
2
1
1
2
2
1
1
1
1
2
1
1
1
3
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Part Desc
HANDLE
WASHER
HANDLE COVER
WASHER
CONNECTING BUSHING
WASHER
SCREW
BASE SEAT
WASHER
WASHER
BASE SEAT
WASHER
NUT
VALVE (HOT)
HOSE
SCREW
SPOUT
PULL ROD
SCREW
WASHER
O-RING
O-RING
BASE
WASHER
O-RING
PIPE
WASHER
SPRING
PULL ROD
HEAD
O-RING
WASHER
WASHER
NUT
PIPE
NUT
VALVE (COLD)
SHOWER
SPRINKLER SOCKET
HOSE
CHECK VALVE
HOSE
DO:
DO NOT:
FR-AZ174
Installation Guide
For more information visit
www.ANZZI.com or call
1-844-44-ANZZI

Ｈａｎｄｌｅ ｉｎｓｔａｌｌａｔｉｏｎ
Ｓｐｏｕｔ ｉｎｓｔａｌｌａｔｉｏｎ
Ｈａｎｄ ｓｈｏｗｅｒ ｈｏｌｄｅｒ ｉｎｓｔａｌｌａｔｉｏｎ
Ｓｔｅｐ １
Ｓｔｅｐ ２
Ｓｔｅｐ ３
Ｓｔｅｐ ４
Ｓｔｅｐ ５
Ｖａｌｖｅ ａｎｄ ｗａｔｅｒ ｓｕｐｐｌｙ ｃｏｎｎｅｃｔｉｏｎ
Ｔｅｓｔｉｎｇ ｃｏｎｎｅｃｔｉｏｎｓ
Disassemble the cold water handle
(identified by a blue dot).
Leave the bottom retainer ring as well as the
rubber and metal washers in place. From
under the bathtub insert the cold water valve
(indentified by a C) in the hole located on the
right of the spout hole.
Using the nut, adjust the height of the valve
so the bottom of the flattened part of the
threads is aligned with the top of the bathtub.
From the top, install the remaining rubber
and metal washers. Screw the nut to secure
the valve, handle flange and handle in place.
Repeat steps to install the handle and hot
water valve (identified by an H) in the hole
located on the left of the spout hole.
2
3
1
4
Unscrew the Allen screw from behind
the spout. Pull apart the spout from its
connector (do not unscrew)
Unscrew the superior spout nut of the
spout connector. Make sure that the nut
and the metal and rubber washers are
in place on the spout connector. From
underneath the bathtub, insert the top
of the connector in the hole between
the two handles. From over the bathtub,
screw the superior spout nut to secure
the connector in place.
Place o-ring underneath the spout flange
and reinstall the spout on the anti-turn
pin, making sure to insert the stop rod in
the stop hole. Tighten spout in place by
screwing the Allen screw behind
the spout.
2
1
3
Unscrew the bottom nut and take off
metal and rubber washers.
Insert the hand shower holder in the
hole making sure to place the o-ring
underneath the fix holder. From under,
screw the rubber and metal washers,
as well as the retainer ring to the holder
in place.
Connect the hose to the hand shower,
making sure that the rubber washer is
in place. From above, slide the hose
through the holder to sit the hand
shower on its base.
1
2
3
Using the flexible connectors included,
connect the valves to the spout
connector. Use the extra flexible
connector to join the spout to the hand
shower hose. Tighten using appropriate
tool (ill. A).
Connect hot and cold valves to the
corresponding water supply lines using
flexible connectors (not included) and
tighten (ill.B).
2
1
B
A
ＷＡＲＮＩＮＧ： Ｒｅｍｏｖｅ ａｅｒａｔｏｒ ｂｅｆｏｒｅ
ｔｅｓｔｉｎｇ ｃｏｎｎｅｃｔｉｏｎｓ． Ｄｏ ｎｏｔ ｏｖｅｒｔｉｇｈｔｅｎ．
Verify that there are no leaks by slowly
opening the hot and cold water. In case
of a leak, shut off the water supply and
tighten connectors 1⁄4 turn using the
appropriate tool. Repeat if necessary.
Turn on the faucet and leave both hot
and cold water running for at least one
minute to evacuate the air trapped in
the pipes. Turn off water.
Assemble the aerator as illustrated and
insert into the spout, tightening by hand.
You can now turn on water supply.
3
2
1