Anzzi FR-AZ273 User manual

RECOMMENDED TOOLS
EXPLODED DRAWING
Notes For reference only. We reserve the right
to make changes without any notice.
:
Please read the followings before installing and usage.
[inch]For Reference only (unit = mm )
DIMENSIONS
FAUCET MAINTENANCE
CARE INSTRUCTIONS
To keep your faucet looking its best, please follow
these simple care instructions:
1. Remove as much surface dirt and film using
clear water and a soft cotton cloth.
2. Use any of the following to remove tough
surface film and build-up:
- Mild liquid detergent
- Non-acidic, non-abrasive gentle liquid cleanser
- Non-abrasive liquid polisher.
3. Once clean, rinse faucet with clear water to
thoroughly remove cleaner or polish and blot
dry with soft cotton cloth.
1. Use abrasive cleansers, cloths, or paper towels.
2. Use any cleaning agents containing acids, polish,
waxes, alcohol, ammonia, bleach, solvents or any
other corrosive or harsh chemical cleansers.
NO.
Part No Qty
CTRR0098
CTYB0522
CTMB0588
CTST0153
ATBH0072
CTCB0031
CTCT0046
CTKB0065
CTCP0363
ATBA0042
CTRR0091
CTDB0436
CTWR0114
CTWR0282
CTWT0071
ATBP0001
ATBP0071
CTNB0063
CTST0013
CTST0224
CTTB0014
CTWR0088
CTDB0423
CTDB0133
CTST0117
CTCP0072
ATBP0267
CTWR0024
CTQP0029
CTWB0048
CTRR0138
CTRR0215
CTPB0468
CTRR0082
CTMB0593
CTRP0067
CTBT0077
CTRR0137
CTDB0424
CTRR0139
CTRR0113
CTBB0026
CTWR0217
CTWT0038
CTNB0156
CTPB0188
CTMB0709
ATBA0100
ATBP0070
CTNB0016
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
21
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
2
1
2
2
1
1
1
1
1
1
1
1
1
1
1
2
1
1
3
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Part Desc
O-RING
BODY
KNOB
SCREW
HANDLE
COVER
COVER
NUT
LIMIT RING
CARTRIDGE
O-RING
BASE
WASHER
WASHER
WASHER
HOSE
HOSE
NUT
SCREW
SCREW
PLUG
WASHER
BASE
HEAD
SCREW
CAP
SPOUT
WASHER
AERATOR
WASHER
O-RING
O-RING
PIPE
O-RING
LIFT ROD
O-RING
SPRING
O-RING
BASE
O-RING
O-RING
PIN
WASHER
WASHER
NUT
PIPE
ADAPTOR
CHECK VALVE
HOSE
NUT
NO.
Part No
CTWR0061
CTPB0499
CTRR0142
CTDB0488
ATBA4028
CTPB0573
CTRR0009
CTSB0157
CTNB0338
CTWR0341
ATBE0141
51
52
53
54
55
56
57
58
59
60
61
1
1
1
1
1
1
1
1
1
2
1
Qty
Part Desc
WASHER
PIPE
O-RING
BASE
CHECK VALVE
PIPE
O-RING
SCREW
NUT
WASHER
SHOWER
DO:
DO NOT:
FR-AZ273
Installation Guide
For more information visit
www.ANZZI.com or call
1-844-44-ANZZI

1
2
Ｈａｎｄｌｅ ｉｎｓｔａｌｌａｔｉｏｎ
Place the base of the handle flange kit
on the left hole. Insert the braided flex
connectors through the hole.
From underneath, place metal washer
and locknut on each threaded stud and
tighten gently by hand.
Now, position and properly align the
handle on top. Tighten the locknuts with
a flat head screwdriver or appropriate
tool. Do not overtighten.
Ｓｐｏｕｔ ｉｎｓｔａｌｌａｔｉｏｎ
Unscrew the Allen screw in back of
the spout. Pull apart the spout from its
connector (do not unscrew). Separate
the spout flange from the spout. Place
o-ring underneath the spout flange and
place the flange over the center hole
between the handle and hand shower.
Unscrew the superior spout locknut of
the spout connector. Make sure that the
locknut and the metal and rubber
washers are in place on the spout
connector. From underneath the
bathtub, insert the top of the
connector in the hole between the
handle and hand shower. From over
the bathtub, screw the superior spout
locknut to secure the connector and the
flange in place.
Install the spout on the connector and
align the spout with the flange, making
sure to insert the anti-rotation pin in
the stop hole. Tighten spout in place by
screwing the Allen screw in front of
the spout.
Ｈａｎｄ ｓｈｏｗｅｒ ｈｏｌｄｅｒ ｉｎｓｔａｌｌａｔｉｏｎ
Unscrew the locknut and take off metal
and rubber washers.
Insert the hand shower holder in the
hole making sure to place the o-ring
underneath the fix holder. From under,
screw the rubber and metal washers,
as well as the retainer ring to the holder
in place.
Connect the hose to the hand shower
hole, making sure that the
rubber washer is in place.
From above, slide the hose through the
holder to sit the hand shower on its
base.
1
2
3
1
3
Ｓｔｅｐ １
Ｓｔｅｐ ２
Ｓｔｅｐ ３
2
3
Ｓｔｅｐ ４
Ｓｔｅｐ ５
1
2
Ｖａｌｖｅ ａｎｄ ｗａｔｅｒ ｓｕｐｐｌｙ ｃｏｎｎｅｃｔｉｏｎ
Using the flexible connectors included
(5), connect the valve to the spout
connector. Use the extra flexible
connector (14) to join the spout to the
hand shower hose.Tighten using
appropriate tool. (ill. A)
Connect hot and cold valves to the
corresponding water supply lines using
flexible connectors and tighten. (ill.B)
Ｔｅｓｔｉｎｇ ｃｏｎｎｅｃｔｉｏｎｓ
WARNING: Remove aerator before
testing connections. Place the
appropriate wrench on the flat edges
and unfasten. Use a cloth to not
damage the part. Do not overtighten.
Verify that there are no leaks by slowly
opening the hot and cold water. In case
of a leak, shut off the water supply and
tighten connectors 1⁄4 turn using the
appropriate tool. Repeat if necessary.
Turn on the faucet and leave both hot
and cold water running for at least one
minute to evacuate the air trapped in
the pipes. Turn off water.
Assemble the aerator as illustrated and
insert into the spout, tightening by hand.
You can now turn on water supply.
1
2
3
ill. A
ill. B