Anzzi L-AZ 904 Series User manual

DON’T WAIT!
REGISTER NOW!
Register your product within 90 days to ensure your product is
recognized as an purchase and is for warranty
coverage.
in the registry card (Pg. 2) or register
at www.swcorp.com/register
.
LEAD FREE
NSF/ANSI/CAN 61
INSTALLATION & OPERATION MANUAL
V1.0
ITEM: L-AZ 904**
2TONE LAVATORY FAUCET
10/30/2022

1
PG.1
TOOLS
PRODUCT SIZE CHART
Wrench Screwdriver
1.38"
[35mm]
2.05"
[52mm]
8.15"
[207mm]
1.5"
[38mm]
0.2"
[5mm]
8.82"
[224mm]
7.8"
[198mm]
8.62"
[219mm] 9.4"
[239mm]
2.05"
[52mm]
6.34"
[161mm]
3/8 COMPRESSION
1.3-1.38"
[33-35mm]

PG.2
[01]
[02]
[03]
[04]
[05]
[06]
[07]
[08]
[09]
[10]
[11]
[12]
[14]
[13]
Description QtyPart.
[01] 1
1
1
1
1
1
1
1
1
1
1
1
1
1
[02]
[03]
[04]
[05]
[06]
[07]
[08]
[09]
[10]
[11]
[12]
[13]
[14]
Handle
Button
Screw
Cap
O-ring
Body
Cartridge
Key
Rubber Gasket
Mounting Kit
O-ring
Metal Gasket
Retainer
Aerator
Before installation:
1.Please make sure that all components have been included.
2.Ensure that all supply lines are free of debris with supply stops installed.
3.Ensure water pressure is between 20-125 PSI.
4. If you are having difficulties with installation, please contact a professional plumber.
COMPONENTS

PG.3
HOT COLD
INSTALLATION
1
2STEP 2:
1.
2.
3.
Make sure all fittings and end connections are
free of debris.
Turn off the supply valves (not provided).
Connect faucet supply hoses to the supply valves,
making sure the red braided hose with “HOT”
label is connected to the hot supply valve and
the blue braided hose with “COLD” label is
connected to the cold supply valve.Hand tighten
the connections first, then finish tightening with
wrench. DO NOT OVERTIGHTEN.
WARNING: Do not use pipe dope or other
sealants on water connections.
[11]
[12]
[13]
[14]
Faucet
STEP 1:
Remove Rubber Gasket [12],Metal Gasket
[13] and Mounting Kit [14] from Faucet.
Install Faucet with O-ring [11] at the bottom
into the faucet hole on sink. Adjust the Faucet.
Slide Rubber Gasket [12], Metal Gasket [13]
up onto Faucet under sink and secure with
Mounting Kit [14].
First hand tighten the Mounting Kit [14] then finish
tightening it with a screwdriver to secure the
Faucet.
1.
2.
3.
4.

[09]
[10]
PUSH POP-UP INSTALLATION
Specification
Body
Gasket
PG.4
Faucet
INSTALLATION
STEP 4:
1.
2.
4
3
Handle
STEP 3:
1.
2.
3.
Remove Body and Gasket from POP-UP drain.
Install the Body and Gasket through the drain
hole of the sink as shown in Figure 4.
Turn on hot and cold water supplies and check all connections for leaks where indicated by arrows. Retighten if
necessary, but Do Not Overtighten.
Using the Key [10], remove Aerator [09] from Faucet.
Turn the Handle to full on position and flush water lines for one minute. Reinstall Aerator [09] with the Key
[10].

PG.5
1.
2.
Washer
Plastic washer
Lock nut
5
Body
Gasket
Outlet pipe
6
INSTALLATION
CLEANING & MAINTENANCE
STEP 5:
Slide Washer, Plastic washer and Lock nut
up onto the Body from under the sink and secure
with Lock nut.
STEP 6:
Install the Outlet pipe with Gasket up onto the
Body from under the sink and tighten it securely.
Note: Ensure there is a Gasket between Body
and Outlet pipe.
To preserve the finish on the metallic parts of your ANZZl faucet , apply non-abrasive wax , such as car
wax. Any cleaners should be rinsed off immediately.
Clean the aerator regularly to remove calcium build-up and any blockages that could reduce water flow.