AP BM000N User manual

Actuator
Specification & Installation Instructions
BM-N_120124.docx 1
Technical Data
BM000N BM000FN BM000FFN BM060N BM060FN BM060FFN BM020N BM020FN BM020FFN
Running time through 90º 15 sec 6 sec 3 sec 15 sec 6 sec 3 sec 15 sec 6 sec 3 sec
Power consumption 10 VA 10 VA 10 VA
18VA Peak,
10VA
18VA Peak,
10VA
18VA Peak,
10VA 10 VA 10 VA 10 VA
Torque 50 in.lb. [5,6 Nm] at rated
voltage
35 in.lb.
[3,9 Nm] at
rated voltage
50 in.lb. [5,6 Nm] at rated
voltage
35 in.lb.
[3,9 Nm] at
rated voltage
50 in.lb. [5,6 Nm] at rated
voltage
35 in.lb.
[3,9 Nm] at
rated voltage
Fail safe - Enerdrive No Yes No
Auxiliary switches No Yes (2)
Ingress protection
IP22 equivalent to Nema type 2, IP54 equivalent to Nema type 3R if water tight
inlet bushings (not supplied NEP617) are installed
IP22 equivalent to Nema type 2
Feedback 4 to 20 mA or 2 to 10 VDC adjustable (default setting: 4 to 20mA)
Power supply 22 to 26 VAC or 28 to 32 VDC
Electrical connection 18 AWG [0.8 mm2] minimum
Inlet bushing 2 inlet bushing of 5/8 in [15.9 mm] & 7/8 in [22.2 mm]
Control signal Analog, Digital or Pulse with modulation (PWM) programmable (default setting: Analog control signal)
Angle of rotation 0 to 90 degrees, mechanically adjustable (default setting: 90º stroke)
Direction of rotation Reversible, Clockwise (CW) or Counterclockwise (CCW) (default setting: CW direction)
Ambient temperature -22ºF to +122ºF [-30º C to +50º C]
Storage temperature -22ºF to +122ºF [-30º C to +50º C]
Relative Humidity 5 to 95 % non condensing.
Weight 3 lbs. [1.4 kg]
Warning: Do not press the clutch when actuator is powered
Dimensions
A
B
C
D
Dimension
Inches
Metric (mm)
A
1.50
38.1
B
3.26
82.8
C
6.60
167.5
D
model 000 & 060
3.01
76.4
model 020
3.72
94.5
Caution
We strongly recommend that all Neptronic
®
products be wired to a separate transformer and that transformer shall service only Neptronic
®
products. This precaution will
prevent interference with, and/or possible damage to incompatible equipment.
When multiple actuators are wired on a single transformer, polarity must be observed. Long wiring runs create voltage drop which may affect the actuator performance.
1Enerdrive System U.S.A. Patent #5,278,454
Feature
•Mounts easy on round & square shaft (with option –8).
:
•External clutch for manual adjustments.
•Maintenance free.
•Position indicator.
•Control signal fully programmable.
•Auto stroke on power up
•Brushless DC driven motor.
•Fail safe by Enerdrive System1
•Auxiliary switches (on model 020)
(on model 060).
BM000N
BM020N
BM060N
BM000FN
BM020FN
BM060FN
BM000FFN
BM020FFN
BM060FFN

BM000/020/060(F)(FF)N
Specification & Installation Instruction
2
Mechanical Installation
CLUTCH
MOUNTING
BRACKET
1.
Manually close the damper blades and positioned the
actuator at 0º or 90º.
2. Slide the actuator onto the shaft.
3. Tighten the nuts on the “U” bolt to the shaft with a 8mm
wrench to a torque of 60 in.lb. [6,7 Nm].
4. Slide the mounting bracket under the actuator. Ensure free
movement of the slot at the base of the actuator. The
bracket pin must be placed in the mid distance of the slot.
5. Fix the bracket to the ductwork with #8 self-tapping screws.
Wiring Diagrams
Analog or PWM
1 2 3 4 5
COMMON (-)
TB1
24 Vac or 30 Vdc (+) INPUT SIGNAL
FEEDBACK
Digital signal
Digital – 3 wire / 2 position
24 Vac (+)
2.2 KΩ
2.2 KΩ
12 3 4 5
FEEDBACK
DRIVE CCW
TB1
COMMON (-)
DRIVE CW
Digital – 4 wire / 3 point floating
2.2 KΩ
2.2 KΩ
1 2 3 4 5
FEEDBACK
DRIVE CCW
COMMON (-)
24 VAC (+)
TB1
DRIVE CW
In this mode, the actuator is sensitive to induced electrical voltages from external sources. To prevent such interference, if the signal on pins 4 and 3
on TB1 are from an external 24 Vac source, install a resistor 2.2kohm, 0.5W between pins 4 and 1 and another of 2.2kohms, 0.5W between pins 3
and 1 of TB1. These resistors are included.
Special consideration for Digital control
Input Signal and Feedback setup
Input Signal Feedback
Analog Mode
Input Signal is set with Dipswitch # 3
DS1-3 at OFF = 2 – 10Vdc (default setting)
DS1-3 at ON = 4 – 20mA Feedback is set with Dipswitch #4
DS1-4 at OFF = 4 – 20mA (default setting)
DS1-4 at ON = 2 – 10Vdc
Digital & PWM
Mode
No Input Signal Setting
!
DS1-3 MUST be at OFF

BM000/020/060(F)(FF)N
Specification & Installation Instruction
3
ON
1 2 3 4
Rotation: CCW
Input in mA Feedback in Vdc
Fail safe return at 90º
ON
1 2 3 4
Rotation: CW
Input in Vdc Feedback in mA
Fail safe return at 0º
PC Board
BM060N/GMR
1 2 3 4 5
ON
1 2 3 4
JP7
Microcontroller
Pins for PWM selection
Reset button
Dip switch
LED
Terminal
Dip switch settings
Default Setting = All dipswitches at OFF
Stroke adjustment – No control signal change
1. Apply power and, WAIT FOR LED TO BE OFF (around 10 seconds).
2. Press and release the reset button to start the auto-stroke process.
The LED should be illuminated.
•First option:
The actuator will then travel in both directions to find its limit and position itself according to the demand.
The LED will extinguish, the process is complete.
•Second option:
When the desired start position is reached, press and release the reset button. The actuator will now go the end
position. (you can also press and release the reset button when It's reaches the end position)
The LED will extinguish, the process is complete.
Programming – Change of control signal & PWM pulse setting
1. Remove power and put all dip switches "OFF" (default setting).
2. Apply power and, within 10 seconds, press and release the reset button. The LED should be blinking.
3. Select the control signal with dip switches:
Digital or Analog Modes
PWM Mode
Move switch No1 "ON” and then “OFF”.
Digital
5 sec. pulse (default setting)
(On/Off or 3 point floating)
Move switch No2 "ON” and then “OFF”.
Analog
25 sec. pulse
(Default)
Stroke adjustment
see the stroke adjustment section above.
Enabling or disabling PWM mode
1. Remove power supply to actuator
2. Install jumper between pin 3 & 4 of JP7
3. Select the desired action using the dipswitches (DS1):
DS1-1
DS1-2
Action
OFF
ON
Enable PWM Mode
ON
OFF
Disable PWM Mode
4. Re-apply power supply to actuator
5. Wait 5 seconds
6. Remove power supply to actuator
7. Remove jumper between pin 3 & 4 of JP7, re-install it between pin 4 & 5.
8. Re-apply power supply to actuator
PWM is factory preset at 5 sec. pulse,
refer to programming section above to change pulse setting.
JP7
Pin #1
Pin #5
Pin #2
Pin #3
Pin #4
When not used for programming,
jumper is placed between pin 4 & 5

BM000/020/060(F)(FF)N
Specification & Installation Instruction
4
Zero and span calibration
This feature is applicable to analog control signal only.
1. Remove power and put all dip switches "OFF". (factory preset).
2. Apply power and, within 10 seconds press and hold the reset button until the LED blinks once.
The Zero and span calibration process then start.
3. Release the reset button. The LED is now constantly illuminated.
4. Apply new minimum voltage.
It can be any value between 0 to 7 Vdc, with an external 0 to 10 volt supply (ex: MEP).
5. Press and release the reset button to memorize the new minimum voltage. The LED blinks.
6. Apply new maximum voltage.
It can be any value between 3 to 10 Vdc, this value should be greater than the new minimum value.
7. Press and release the reset button to memorize the new maximum voltage. The LED blinks.
The Zero and span calibration process is complete.
Note: To reset zero and span to 2 to 10 Vdc (default setting). You just have to re-select the analog control signal mode, see
Programming.
Wiring Diagrams for auxiliary switches (on model 020)
BLACK
RED
GREEN
BROWN
WHITE
BLUE
LOWER COMMON
LOWER CLOSED 10-90º
LOWER CLOSED 0-10º
UPPER COMMON
UPPER CLOSED 0-80º
UPPER CLOSED 80-90º
Auxiliary switch rating:
5 Amp resistive, 250 Vac