AP UM200 User manual

Actuator
Specification & Installation instructions
UM2-WM2_110728 1
Technical
Data UM200 UM220 UM210 UM230 WM200 WM220 WM210 WM230
Auxiliary switches No Yes (2) No Yes (2) No Yes (2) No Yes (2)
Fail safe No Yes No Yes
Torque 2500 in.lb. [280 Nm] at rated voltage 4000 in.lb. [450 Nm] at rated voltage
Running time
through 90º 4 min. 8 min.
Feedback 4 to 20 mA or 2 to 10 VDC adjustable
Power consumption 40 VA
Power supply 28 to 32 VDC or 22 to 26 VAC, 220 to 250 VAC 50/60Hz
Electrical connection 18 AWG [0.8 mm2] minimum
Inlet bushing 3 inlet bushing of 7/8 in [22.2 mm]
Control signal Analog or Digital programmable (factory set with Analog control signal)
Angle of rotation 0 to 110 degrees, electronically adjustable (factory set with 110º stroke)
Direction of rotation Reversible, Clockwise (CW) or Counterclockwise (CCW) (factory set with CW direction)
Ambient temperature 0ºF to +122ºF [-18º C to +50º C]
Storage temperature -22ºF to +122ºF [-30º C to +50º C]
Relative Humidity 5 to 95 % non condensing.
Weight 29 lbs. [13 kg]
Warning: Do not press the clutch when actuator is powered
Dimensions
Dimension Inches Metric (mm)
A 6.75 169.4
B 7.95 201.9
C 7.85 199.4
D 14.45 367.0
Caution
We strongly recommend that all neptronic® products be wired to a separate transformer and that transformer shall service only neptronic® products. This precaution will
prevent interference with, and/or possible damage to incompatible equipment.
When multiple actuators are wired on a single transformer, polarity must be observed. Long wiring runs create voltage drop which may affect the actuator performance.
Feature:
•Up to 4000 in.lb [450Nm].
•Clutch for manual adjustments.
•Maintenance free.
•Control signal fully programmable.
•Fail safe (battery backup)
(on model 210 & 230).
•Auxiliary switches (on model 220 & 230).
•IP56 enclosure.
UM200
UM220
UM210
UM230
WM200
WM220
WM210
WM230

UM200/220/210/230
WM200/220/210/230 Specification & Installation instruction
2
Exploded view
BATTERY KEYWAY
MAIN SHAFT
TOP COVER
PC BOARD
WIRING ACCESS
Wiring Diagrams
Analog line voltage
12345
COMMON (-)
TB1 1 2
NEUTRAL
LINE
TB5
INPUT SIGNAL
FEEDBACK
Analog low voltage
1 2 3 4 5
COMMON (-)
TB1
24 Vac or 30 Vdc (+) INPUT SIGNAL
FEEDBACK
Digital signal from internal source
Digital
–
3 wire / 2 position
1 2 34 5
DRIVE CW
COMMON (-)
DRIVE CCW
1 2
NEUTRAL
LINE
TB5
TB1 FEEDBACK
Digital
–
4 wire / 3 point floating
1 2 3 4 5
DRIVE CW
DRIVE CCW
1 2
NEUTRAL
LINE
TB5
TB1
COMMON (-) FEEDBACK
Digital signal
Digital
–
3 wire / 2 position
2.2 KΩ
2.2 KΩ
1 2
NEUTRAL
LINE
TB5
12345
DRIVE CW DRIVE CCW
24 Vac (+)
TB1
COMMON (-) FEEDBACK
Digital
–
4 wire / 3 point floating
2.2 KΩ
2.2 KΩ
1 2
NEUTRAL
LINE
TB5
1 2 3 4 5
DRIVE CW DRIVE CCW
COMMON (-)
24 VAC (+)
TB1 FEEDBACK
Special consideration for Digital control
In this mode, the actuator is sensitive to induced electrical voltages from external sources. To prevent such interference, if the signal on pins 4 and 3
on TB1 are from an external 24 Vac source, install a resistor 2.2kohm, 0.5W between pins 4 and 1 and another of 2.2kohms, 0.5W between pins 3
and 1 of TB1. These resistors are included.
Input Signal and Feedback setup
Input Signal Feedback
Analog Mode Input Signal is set with Dipswitch # 3
DS1-3 at OFF = 2 – 10Vdc (default setting)
DS1-3 at ON = 4 – 20mA Feedback is set with Dipswitch #4
DS1-4 at OFF = 4 – 20mA (default setting)
DS1-4 at ON = 2 – 10Vdc
Digital Mode
No Input Signal Setting
!
DS1-3 MUST be at OFF

UM200/220/210/230
WM200/220/210/230 Specification & Installation instruction
3
ON
1 2 3 4
Rotation: CCW
Input in mA Feedback in Vdc
Fail safe return at 90º
ON
1 2 3 4
Rotation: CW
Input in Vdc Feedback in mA
Fail safe return at 0º
PC Board
Potentiometer
Dip switch
Reset button LED
Terminal
Clutch
Line voltage terminal
TB5
Fuse
1 2 3 4 5
TB1
N L
ON
1
DS1 4
23
Dip switch settings
Default Setting = All dipswitches at OFF
Stroke adjustment – No control signal change
1. Apply power and, wait for at least 10 seconds.
2. /Press and release the reset button to start the auto-stroke process.
The LED should be illuminated.
•First option:
The actuator will then travel in both directions to find it's limit and position itself according to the demand.
The LED will extinguish, the process is complete.
•Second option:
When the desired end position is reached, press and release the reset button. The actuator will now return back to
its original position. (you can also press and release the reset button when It's reaches the original position)
The LED will extinguish, the process is complete.
Programming – Change of control signal
1. Remove power and put all dip switches "OFF". (factory preset).
2. Apply power and, within 10 seconds, press and release the reset button. The LED should be blinking.
3. Select the control signal with dip switches:
•Digital (On/Off or 3 point floating)
move switch No1 "ON” and then “OFF”.
•Analog (factory preset)
move switch No2 "ON” and then “OFF”.
1. Stroke adjustment
see the stroke adjustment section above.

UM200/220/210/230
WM200/220/210/230 Specification & Installation instruction
4
Zero and span calibration
This feature is applicable to analog control signal only.
1. Remove power and put all dip switches "OFF". (factory preset).
2. Apply power and, within 10 seconds press and hold the reset button until the LED blinks.
The Zero and span calibration process then start.
3. Release the reset button. The LED is now constantly illuminated.
4. Apply new minimum voltage.
It can be any value between 0 to 7 VDC, with an external 0 to 10 volt supply (ex: MEP).
5. Press and release the reset button to memorize the new minimum voltage. The LED blinks.
6. Apply new maximum voltage.
It can be any value between 3 to 10 VDC, this value should be greater than the new minimum value.
7. Press and release the reset button to memorize the new maximum voltage. The LED blinks.
The Zero and span calibration process is complete.
Note: To reset zero and span to 2 to 10 VDC (factory value). You just have to re-select the analog control signal mode, see
Programming.
Wiring Diagrams for auxiliary switches (on model 220 & 230)
BLACK
RED
GREEN
BROWN
WHITE
BLUE
LOWER COMMON
LOWER CLOSED 10-90º
LOWER CLOSED 0-10º
UPPER COMMON
UPPER CLOSED 0-80º
UPPER CLOSED 80-90º
Auxiliary switch rating:
5 Amp resistive, 250 Vac