Apacer Technology AS2280Q4 User manual

-1-
Quick Guide
AS2280Q4 PCIe Gen 4x4
M.2 NVMe SSD
English 繁體中文 簡體中文

-2-
Apacer provides a free dedicated M.2 SSD heatsink with special
diversion cutting design to effectively reduce the PCIe 4.0 SSD
temperature to maintain reading and writing performance at
optimum levels.
This quick guide is guiding you how to assemble and disassemble
the enclosed heatsink of Apacer AS2280Q4 M.2 PCIe Gen 4x4 SSD.
Please check it carefully before you installed it to your device.
AS2280Q4 PCIe Gen 4x4 M.2 NVMe SSD x 1pcs
Heatsink Top x 1pcs
- Heatsink Bracket x 1pcs
- Thermal Tape x 1pcs
Contents
1
1
2
2
3
3
4
4

-3-
Step 1 :
Step 2 :
Insert the m.2 SSD horizontally according to the bridge in the bracket.
After placing the m.2 SSD in the bracket, please checking if there is room for
connector and half moon screw holes.
Assembly Procedure

-4-
Step 3 :
Step 4 :
Attaching the thermal adhesive tape to the heatsink, and tearing off the
release paper for placing the heatsink later.
Place the heatsink on the bracket and align it with one side. Put two ngers
on both ends and press down with appropriate force. Press the heatsink
into the latch of the bracket.

-5-
Step 5 :
Check if the heatsink is locked into the bracket and complete the assembly.
Step 1 :
Prepare a athead screwdriver. Insert the athead screwdriver into the one
of the latch of the bracket.
Disassembly Procedure
Assembly completed!

-6-
Step 2 :
Gently detach the latch of the bracket. Then you can detach another latch
of the bracket.
Step 3 :
After completing the previous steps, you can gently remove the heatsink
from the bracket.
Disassembly completed!
*Notice: The enclosed heatsink is free without warranty.

-7-
宇瞻科技提供免費的 M.2 固態硬碟專屬散熱器，採特殊的分流
切割設計，有效降低 PCIe 4.0 SSD 溫度，使其讀寫性能保持在
最佳水準。
本快速指南將指導您如何組裝和拆卸 Apacer AS2280Q4 M.2
PCIe Gen 4x4 SSD 的專屬散熱器。在將其安裝到您的設備之前，
請仔細查閱。
AS2280Q4 PCIe Gen 4x4 M.2 NVMe SSD x 1 個
散熱器頂部 x 1 個
散熱器支架 x 1 個
散熱膠帶 x 1 片
內容
1
1
2
2
3
3
4
4

-8-
步驟 1：
步驟 2：
延著支架內的軌道水平插入 m.2 SSD。
將 m.2 SSD 放入支架後，請檢查是否有保留左右兩側連接器和半月螺絲
孔的空間。
裝配程序

-9-
步驟 3：
步驟 4：
將散熱膠帶粘貼到散熱器上，然後撕下玻璃紙以便固定散熱片。
將散熱器放在支架上並將其與一側對齊，運用兩根手指放在散熱器頂部
兩端，並用適當的力按下，將散熱器按入支架的閂鎖。

-10-
步驟 5：
檢查散熱器是否鎖定在支架中並完成組裝。
步驟 1：
準備一個平頭螺絲刀，將平頭螺絲刀插入支架的一個鎖扣中。
拆卸程序
裝配完成！