Aplex OPD-1086 User manual

OPD-11x6 User Manual
1
OPD-1086/1106/1126/1156/1176/1196
Display Monitor User Manual
Release Date Revision
Nov. 2014 V1.2
® 2014 Aplex Technology, Inc. All Rights Reserved. Published in
Taiwan
Aplex Technology, Inc.
9F-5, No. 2, Jian Pa Road, Chung Ho City, Taipei County, Taiwan
Tel: [phone] Fax: [phone] E-mail: [email protected]w URL:
www.aplex.com.tw

OPD-11x6 User Manual
2
Warning!___________________________________
This equipment generates, uses and can radiate radio frequency energy and if not installed and
used in accordance with the instructions manual may cause interference to radio communications.
It has been tested and found to comply with the limits for a ClassA computing device pursuant to
FCC Rules, which are designed to provide reasonable protection against such interference when
operated in a commercial environment. Operation of this equipment in a residential area is likely
to cause interference in which case the user at his own expense will be required to take whatever
measures may be required to correct the interference.
Electric Shock Hazard –Do not operate the machine with its back cover removed. There are
dangerous high voltages inside.

OPD-11x6 User Manual
3
Table of Contents______________________
Warning!…………………………………………………………………………….……..….2
Chapter 1 Getting Started
1.1 Features………………………………………………………….………….5
1.2 Specifications…………………………………………. ...……………...….5
1.3 Dimensions…………………………………...………………………….…7
1.4 Brief Description..................................................................................10
1.5 Display Mode………………………………………………………………11
Chapter 2 OSD
2.1 OSD Functions….……………….……………………………….…..…….12
2.2 OSD Controls………………………………………………………………13
2.3 Main Menu…..……………………………………………………………..14
Chapter 3 Control Board
3.1 Introduction to the PenMount 9036CH5 Touch Screen Control Board (For
RS-232 interface Touch Screen)…………………………...……………….16
3.2 Introduction to the PenMount 6300A5 Touch Screen Control Board (For
USB interface Touch Screen)………………………………….……………19
Chapter 4 Installation
4.1 Windows XP/2003/Vista/Win7 Driver Installation for PenMount
9036CH5/6300A5 Control Board……………………………………………22
4.2 Configuring the PenMount Windows XP/2003/Vista/Win7 Driver25
4.3 Uninstall the PenMount Windows XP/2003/Vista/Win7 Driver……32
Chapter 5 Software
5.1 Software Functions…………………………………………………………33
5.2 Software Function Descriptions……………………..……………….…..34
Figures
Figure 1.1: Dimensions of OPD-1086….……………………………………..7
Figure 1.2: Dimensions of OPD-1106….……………………………………..7
Figure 1.3: Dimensions of OPD-1126….……………………………………..8

OPD-11x6 User Manual
4
Figure 1.4: Dimensions of OPD-1156…..…………………………………….8
Figure 1.5: Dimensions of OPD-1176….……………………………………..9
Figure 1.6: Dimensions of OPD-1196….……………………………………..9
Figure 1.7: Overall View………………………………………………………10
Figure 1.8: Rear View…………………..……………………………………..10
Figure 3.1: Overview of PenMount 9036CH5 Control Board………………16
Figure 3.2: Dimensions of PenMount 9036CH5 Control Board……………17
Figure 3.3 Overview of PenMount 6300A5 Control Board…………………19
Figure 3.4 Dimensions of PenMount 6300A5 Control Board…………………20

OPD-11x6 User Manual
5
Chapter 1________________Getting Started
1.1 Features
1.2 Specifications
Display
Environment
Operating Temperature: 0~50˚C (32˚~122˚F)
Storage Temperature: -20~60˚C (-4˚~140˚F)
Relative Humidity: 10~90% @40˚C non-condensing, without touch screen
Vibration: 1g peak, 5~500Hz (at random)
Shock: 10G peak acceleration (11msec. duration)/operation
Certifications: Meet CE, FCC Class A
Model
OPD-1086
OPD-1106
OPD-1126
OPD-1156
OPD-1176
OPD-1196
Display
8”TFT LCD
10.4”TFT LCD
12.1”TFT LCD
15”TFT LCD
17”TFT LCD
19”TFT LCD
Luminance
400 cd/m²
250 cd/m²
400 cd/m²
350 cd/m²
300 cd/m²
300 cd/m²
Resistive touch screen (optional)
Optional DVI, Video or S-Video input
Supports wide-ranging resolutions from 640x480 to up to 1600 x 1200 with auto phase and auto
position.
Model
OPD-1086
OPD-1106
OPD-1126
OPD-1156
OPD-1176
OPD-1196
Luminance
400 cd/m²
250 cd/m²
400 cd/m²
350 cd/m²
300 cd/m²
300 cd/m²
Viewing Angle
H:125/V:140
H:130/V:110
H:160/V:140
H:150/V:140
H:140/V130
H:160/V:160
Resolution
800x600
800x600
800x600
1024x768
1280x1024
1280x1024
Backlight
lifetime
40000hrs
20000hrs
50000hrs
50000hrs
50000hrs
50000hrs
Touch Screen
Resistive touch screen (optional)
OSD Control
Indicators
Automatic screen, setup (OSD), brightness, contrast, horizontal/vertical position,
image lock, color balance, video information, power on and sync detected
OS
Compatibility
Win XP
Power Input
Input 11~32V/DC

OPD-11x6 User Manual
6
Mechanical
Ordering Information
OPD-1086
8”SVGA open frame display monitor
OPD-1106
10.4” SVGA open frame display monitor
OPD-1126
12.1” SVGA open frame display monitor
OPD-1156
15” XGA open frame display monitor
OPD-1176
17”SXGA open frame display monitor
OPD-1196
19” SXGA open frame display monitor
Options
Resistive touch screen
Model
OPD-1086
OPD-1106
OPD-1126
OPD-1156
OPD-1176
OPD-1196
Construction
Steel Chassis
Dimensions
208X148mm
260x213mm
300x250mm
357x291mm
410x330mm
423x333mm
Mounting Type
Panel Mount

OPD-11x6 User Manual
7
1.3 Dimensions
Figure 1.1: Dimensions of the OPD-1086
Figure 1.2: Dimensions of the OPD-1106

OPD-11x6 User Manual
8
Figure 1.3: Dimensions of the OPD-1126
Figure 1.4: Dimensions of the OPD-1156

OPD-11x6 User Manual
9
Figure 1.5: Dimensions of the OPD-1176
Figure 1.6: Dimensions of the OPD-1196

OPD-11x6 User Manual
10
1.4 Brief Description of the OPD-11x6
The OPD-11x6 offers 8”/ 10.4”/12.1/15”/17”/19”LCD open frame display the feature an excellent
viewing ability for special monitoring and control applications, especially in Industrial area. It is
available with resistive touch screen that is easy to use and maintain.
Figure 1.7: Overall View of OPD-11x6
Figure 1.8: Rear View of OPD-11x6

OPD-11x6 User Manual
11
1.5 Display Mode
Display Mode
Hori. Sync (KHz)
Vert. Sync. (Hz)
31
60
VGA 640 x 480
38
72
38
75
35
56
SVGA 800 x 600
38
60
48
72
47
75
48
60
XGA 1024 x 768
56
70
60
75
SXGA
1152 x 864
68
75
1280 x 1024
64
60
80
75

OPD-11x6 User Manual
12
Chapter 2_________________________OSD
2.1 OSD Functions
Power switch: To turn ON or OFF the power
Shift the icon to the right side or shift it up
Shift the icon to the left side or shift it down
Menu: To enter OSD menu for related icon and item.
Auto Button: One-touch auto adjustment
1.) Getting into Burn-in Mode
Before setting into a burn-in mode, first disconnect the AC power cord. Then press (don’t let them go)
the buttons until the AC power cord is connected and the “RGB” appears on the top left corner
of your screen. Now it can be put into the burn-in mode for changing colors.
2.) Getting Out of Burn-in Mode
Before getting out of the burn-in mode, please first disconnect the AC power cord. Then press the
button (If not workable, press the button and don’t let them go) until the AC power cord is
connected. Please don’t let your fingers go until the AC power cord is connected again and the
wording of “RGB”appears on the top left corner of your screen, and wait for 3 second. Under the
non-signal entry situation, if is seen, exit is thus successfully made.
Cable Not Connected

OPD-11x6 User Manual
13
2.2 OSD Controls
To make any adjustment, select the following:
1. Press (Menu) to show the OSD menu or disable the OSD menu.
2. Select the icon that you wish to adjust with the ( / or +/-) key in the menu.
3. Press (Menu) and then choose the item with the ( / or +/-) key.
4. Press (Menu) and then adjust the quality with the ( / or +/-) key.
1.) If the “RGB”is still on the top left corner of the screen, press to enter “Miscellaneous”and
choose “Reset”, and then Yes, and press . When the screen goes black, disconnect power and
repeat the above steps.
2.) If the “RGB”is not found, disconnect the AC power cord first. Then press the buttons
(don’t let them go) until the AC power cord is connected, and wait for 2 to 3 seconds. When
“RGB”appears, repeat the above steps.
3.) Functions of OSD Keys

OPD-11x6 User Manual
14
2.3 Main Menu
In the Main menu, there are the following items:
Color
Image Setting
Position
OSD Menu
Language
Misc
Exit
For Color, check out the following:
Contrast
Brightness
Color Adjust
Color Temp
Back
For Image setting, check out the following:
Clock
Phase
Gamma
Sharpness
Back

OPD-11x6 User Manual
15
In the Position, there are the following:
H. Position
V. Position
Back
In the OSD menu, there are:
OSD H. Pos.
OSD V. Pos.
OSD Timer
Back
In the Language menu, there are:
English
Frances
Germany
Spanish
Traditional Chinese
Simplified Chinese
Japanese
In the Misc menu, there are:
Signal Source
Select VGA: Analogue VGA Input
Select DVI: Digital DVI-D Input
Select AV: Composite Video Input
Select SV: S-Video Video Input
Reset
Back

OPD-11x6 User Manual
16
Chapter 3________________Control Board
3.1 Introduction to the PenMount 9036CH5 Touch Screen
Control Board (For RS-232 interface Touch Screen)
PenMount 9036CH5 Control board is a powerful RS-232 touch screen control board to support
5-wire touch screen by executing the same drivers as all PenMount series control board and ICs.
PenMount 9036CH5 is good for all kinds of resistive touch screens, user could put PenMount
9036CH5 control board in different systems space and connected to system’s serial interface. There
are two connectors on board, one connector is for the power and RS-232 interface, power line is
allowed to have 5V input, RS-232 interface cable has 9-pin D-sub connector, another is for 5-wire
touch screen.
PM9036CH5 supports 5 wires touch panel, there is a 0 ohm resistance of R13 in the circuit, therefore,
we don’t mount the component. There’s a 0 ohm resistance of R12 in the circuit.
Figure 3.1 Overview of PenMount 9036CH5 Control Board

OPD-11x6 User Manual
17
3.1.1 Mechanical Size
Figure 3.2 Dimensions of PenMount 9036CH5 Control Board
3.1.2 Electrical Specifications
Touch Screen
For 5-wrie analog resistive type
Interface
RS-232
Baud Rate
19200 baud rate selection, N81
Mode selection
PnP mode
Resolution
2048 x 2048
Resistance Range
50~1.3K ohm
Electrostatic Discharge
(ESD)
Air Discharge 15KV
Contact Discharge 8KV
Power Input
+5V DC
Operating Temperature
-20~70˚C
Storage Temperature
-40~85˚C
Mechanical Size
60 x 26 mm, two 3φscrew holes
Diagnostic
LED on board
Power Consumption
Standby Mode: 16mA; Active Mode: 27.5 mA
( VCC=+5V, Top sheet Panel Resistance: 365 ohm ;
Bottom sheet Panel Resistance: 660 ohm )
Note. Actual current will be different by touch panel’s resistance

OPD-11x6 User Manual
18
3.1.3 Driver Software
Windows XP / 2003 / 2008 / Vista / 7,
Windows CE 6.0
3.1.4 Connector Definition
JP1 RS-232 Connector:
PIN 1
Ground
PIN 2
Power Input
PIN 3
RTS
PIN 4
TXD
PIN 5
RXD
PIN 6
Ground
JP2 Touch Screen Lines:
PM9036CH5
5-Wire
PIN 1
Ground
PIN 2
UL (Y)
PIN 3
UR (H)
PIN 4
LL (L)
PIN 5
LR (X)
PIN 6
Sense (S)
PIN 7
---
PIN 8
---
PIN 9
---

OPD-11x6 User Manual
19
3.2 Introduction to the PenMount 6300A5 USB Interface Control
Board (For USB interface Touch Screen)
PenMount 6300A5 USB control board is a touch screen control board designed for USB
interface and specific for 5-wire touch screen. It is designed with USB interface features with multiple
devices supporting function. PenMount 6300A5 control board using PenMount 6000 controller that
has been designed for those who may like all-in-one solution with A/D converter built-in to make the
total printed circuit board denser. There are two connectors on this board, one connector is for 5-wire
touch screen cable, and the other is for 4-pin USB A type cable.
PM6300A5 supports 5 wires touch panel, there’s a 0hm resistance of R12 in the circuit, therefore, we
don’t mount the component.
Figure 3.3 Overview of PenMount 6300A5 Control Board

OPD-11x6 User Manual
20
3.2.1 Mechanical Size
Figure 3.4 Dimensions of PenMount 6300A5 Control Board
3.1.2 Electrical Specifications
Touch Screen
For 5-wire analog resistive type
Communications
USB Full-speed, 12Mbps
Touch Screen Controller
PenMount 6000 controller IC
Resolution
2048 x 2048
Size
60 x 26 mm, two 3φscrew holes
Cursor accuracy
< 1% (ActiveArea Diagonal of touch screen with PenMount
Advanced calibration utility support)
Resistance Range
50~1.3K ohm
Diagnostic
LED on board
Operating Voltage
+5V DC