Apogee MP Series User manual

APOGEE INSTRUMENTS, INC. | 721 WEST 1800 NORTH, LOGAN, UTAH 84321, USA
TEL: [phone] | FAX: [phone] | WEB: APOGEEINSTRUMENTS.COM
Copyright © 2021 Apogee Instruments, Inc.
OWNER’S MANUAL
SOLAR RADIATION METER
Models MP-100 and MP-200
Rev: 1-Jun-2021

TABLE OF CONTENTS
Owner’s Manual ............................................................................................................................................................................... 1
Certificate of Compliance......................................................................................................................................................... 3
Introduction ............................................................................................................................................................................. 4
Sensor Models ......................................................................................................................................................................... 5
Specifications ........................................................................................................................................................................... 6
Deployment and Installation.................................................................................................................................................... 9
Battery Installation and Replacement.................................................................................................................................... 10
Operation and Measurement ................................................................................................................................................ 11
Apogee AMS Software ........................................................................................................................................................... 15
Maintenance and Recalibration............................................................................................................................................. 17
Troubleshooting and Customer Support................................................................................................................................ 19
Return and Warranty Policy................................................................................................................................................... 21

CERTIFICATE OF COMPLIANCE
EU Declaration of Conformity
This declaration of conformity is issued under the sole responsibility of the manufacturer:
Apogee Instruments, Inc.
721 W 1800 N
Logan, Utah 84321
USA
for the following product(s):
Models: MP-100, MP-200
Type: Pyranometer Meter
The object of the declaration described above is in conformity with the relevant Union harmonization legislation:
2014/30/EU Electromagnetic Compatibility (EMC) Directive
2011/65/EU Restriction of Hazardous Substances (RoHS 2) Directive
2015/863/EU Amending Annex II to Directive 2011/65/EU (RoHS 3)
Standards referenced during compliance assessment:
EN 61326-1:2013 Electrical equipment for measurement, control and laboratory use –EMC requirements
EN 50581:2012 Technical documentation for the assessment of electrical and electronic products with respect to
the restriction of hazardous substances
Please be advised that based on the information available to us from our raw material suppliers, the products
manufactured by us do not contain, as intentional additives, any of the restricted materials including lead (see
note below), mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB), polybrominated
diphenyls (PBDE), bis(2-ethylhexyl) phthalate (DEHP), butyl benzyl phthalate (BBP), dibutyl phthalate (DBP), and
diisobutyl phthalate (DIBP). However, please note that articles containing greater than 0.1% lead concentration are
RoHS 3 compliant using exemption 6c.
Further note that Apogee Instruments does not specifically run any analysis on our raw materials or end products
for the presence of these substances, but rely on the information provided to us by our material suppliers.
Signed for and on behalf of:
Apogee Instruments, June 2021
Bruce Bugbee
President
Apogee Instruments, Inc.

INTRODUCTION
Solar radiation at Earth’s surface is typically defined as total radiation across a wavelength range of 280 to 4000
nm (shortwave radiation). Total solar radiation, direct beam and diffuse, incident on a horizontal surface is defined
as global shortwave radiation, or shortwave irradiance (incident radiant flux), and is expressed in Watts per square
meter (W m-2, equal to Joules per second per square meter).
Pyranometers are sensors that measure global shortwave radiation. Apogee MP series solar radiation meters
incorporate silicon-cell pyranometers, and are only sensitive to a portion of the solar spectrum, approximately
350-1100 nm (approximately 80 % of total shortwave radiation is within this range). However, silicon-cell
pyranometers are calibrated to estimate total shortwave radiation across the entire solar spectrum. Silicon-cell
pyranometer specifications compare favorably to specifications for World Meteorological Organization (WMO)
moderate and good quality classifications and specifications for International Organization of Standardization (ISO)
Class C classification, but because of limited spectral sensitivity, they do not meet the spectral specification
necessary for WMO certification.
Typical applications of silicon-cell pyranometers include incoming shortwave radiation measurement in
agricultural, ecological, hydrological weather networks, and solar panel arrays.
Apogee Instruments MP series solar radiation meters consist of a handheld meter and a dedicated pyranometer
that is integrated into the top of the meter housing (MP-100) or connected by cable to an anodized aluminum
housing (MP-200). Integrated and separate sensors consist of a cast acrylic diffuser (filter), photodiode, and are
potted solid with no internal air space. MP series meters provide a real-time irradiance reading on the LCD display
that determines the radiation incident on a planar surface (does not have to be horizontal), where the radiation
emanates from all angles of a hemisphere. MP series meters include manual and automatic data logging features
for making spot-check measurements or calculating daily solar insolation.

SENSOR MODELS
Apogee MP series solar radiation meters covered in this manual are self-contained and come complete with
handheld meter and sensor.
Sensor model number and serial number are
located on a label on the backside of the handheld
meter.
MP-100
MP-200

SPECIFICATIONS
Calibration Traceability
Apogee Instruments MP series solar radiation meters are calibrated through side-by-side comparison to the mean
of four Apogee model SP-110 transfer standard pyranometers (shortwave radiation reference) under high intensity
discharge metal halide lamps. The transfer standard pyranometers are calibrated through side-by-side comparison
to the mean of at least two ISO-classified reference pyranometers under sunlight (clear sky conditions) in Logan,
Utah. Each of four ISO-classified reference pyranometers are recalibrated on an alternating year schedule (two
instruments each year) at the National Renewable Energy Laboratory (NREL) in Golden, Colorado. NREL reference
standards are calibrated to the World Radiometric Reference (WRR) in Davos, Switzerland.
MP-100
MP-200
ISO 9060:2018
Class C (previously known as second class)
Calibration Uncertainty
± 5 % (see Calibration Traceability below)
Measurement
Repeatability
Less than 1 %
Long-term Drift
(Non-stability)
Less than 2 % per year
Non-linearity
Less than 1 % (up to 1750 W m-2)
Response Time
Less than 1 ms
Field of View
180º
Spectral Range
360 to 1120 nm (wavelengths where response is 10 % of maximum;
see Spectral Response below)
Directional (Cosine)
Response
± 5 % at 75º zenith angle (see Cosine Response below)
Temperature Response
0.04 ± 0.04 % per C (see Temperature Response below)
Operating Environment
0 to 50 C; less than 90 % non-condensing relative humidity up to 30 C; less than
70 % non-condensing relative humidity from 30 to 50 C; separate sensors can be
submerged in water up to depths of 30 m
Meter Dimensions
126 mm length; 70 mm width; 24 mm height;
Sensor Dimensions
24 mm diameter; 33 mm height
Mass
150 g
180 g
Cable
2 m of two conductor, shielded, twisted-pair wire; TPR jacket (high water
resistance, high UV stability, flexibility in cold conditions)

Spectral Response
Temperature Response
Mean temperature response of four
Apogee silicon-cell pyranometers.
Temperature response measurements
were made at approximately 10 C
intervals across a temperature range of
approximately -10 to 50 C under
sunlight. Each pyranometer had an
internal thermistor to measure
temperature. At each temperature set
point, a reference blackbody
pyranometer was used to measure solar
intensity.
Spectral response estimate of Apogee
silicon-cell pyranometers. Spectral
response was estimated by multiplying
the spectral response of the
photodiode, diffuser, and adhesive.
Spectral response measurements of
diffuser and adhesive were made with a
spectrometer, and spectral response
data for the photodiode were obtained
from the manufacturer.

Cosine Response
Mean cosine response of eleven Apogee
silicon-cell pyranometers (error bars
represent two standard deviations
above and below mean). Cosine
response measurements were made
during broadband outdoor radiometer
calibrations (BORCAL) performed during
two different years at the National
Renewable Energy Laboratory (NREL) in
Golden, Colorado. Cosine response was
calculated as the relative difference of
pyranometer sensitivity at each solar
zenith angle to sensitivity at 45° solar
zenith angle. The blue symbols are AM
measurements, the red symbols are PM
measurements.
Directional, or cosine, response is defined as the
measurement error at a specific angle of radiation
incidence. Error for Apogee silicon-cell pyranometers is
approximately ± 2 % and ± 5 % at solar zenith angles of
45° and 75°, respectively.

DEPLOYMENT AND INSTALLATION
Apogee MP series solar radiation meters are designed for spot-check measurements, and calculation of daily
insolation (total solar radiation incident on a planar surface over the course of a day) through the built-in logging
feature. To accurately measure global shortwave radiation incident on a horizontal surface, the sensor must be
level. For this purpose, each MP model comes with a different option for mounting the sensor to a horizontal
plane.
In addition to leveling, all sensors should also be mounted such that obstructions (e.g., weather station
tripod/tower or other instrumentation) do not shade the sensor.
The AL-210 leveling plate is recommended
for use with the MP-100.
The AL-100 leveling plate is recommended
for use with the MP-200. To facilitate
mounting to a cross arm, the AL-120
mounting bracket is recommended.

BATTERY INSTALLATION AND REPLACEMENT
Use a phillips head screwdriver to remove the screw from the battery cover. Remove the battery cover by slightly
lifting and sliding the outer edge of the cover away from the meter.
To power the meter, slide the included battery (CR2320) into the battery holder, after removing the battery door
from the meter’s back panel.
The positive side (designated by a “+” sign) should be facing out from the meter circuit board.
NOTE: The battery cradle can be damaged by using an incorrectly sized battery. If the battery cradle is damaged,
the circuit board will need to be replaced. To avoid this costly problem, use only a CR2320 battery.
Battery Removal
Press down on the battery with a screwdriver or similar object. Slide battery out.
If the battery is difficult to move, turn the meter on its side so that the opening for the battery is facing downward
and tap the meter downward against an open palm to dislodge the battery enough so that it can be removed with
your thumb to slide the battery out of the battery holder.

OPERATION AND MEASUREMENT
MP series solar radiation meters are designed with a user-friendly interface allowing quick and easy
measurements.
Press the power button to activate the LCD display. After two minutes of non-activity the meter will revert
to sleep mode and the display will shut off to conserve battery life.
Press the mode button to access the main menu, where the appropriate logging (manual or automatic) is
selected and where the meter can be reset.
Press the sample button to log a reading while taking manual measurements.
Press the up button to make selections in the main menu. This button is also used to view and scroll
through the logged measurements on the LCD display.
Press the down button to make selections in the main menu. This button is also used to view and scroll
through the logged measurements on the LCD display.
Logging: To choose between manual or automatic logging, push the mode button once and use the up/down
buttons to make the appropriate selection (SMPL or LOG). Once the desired mode is blinking, press the mode
button two more times to exit the menu. When in SMPL mode press the sample button to record up to 99 manual
measurements (a counter in the upper right hand corner of the LCD display indicates the total number of saved
measurements). When in LOG mode the meter will power on/off to make a measurement every 30 seconds. Every
30 minutes the meter will average the sixty 30 second measurements and record the averaged value to memory.
The meter can store up to 99 averages and will start to overwrite the oldest measurement once there are 99
measurements. Every 48 averaged measurements (making a 24 hour period), the meter will also store an
integrated daily total in mega joules per square meter per day (MJ m-2 d-1).
Reset: To reset the meter, in either SMPL or LOG mode, push the mode button twice (RUN should be blinking),
then while pressing the down button, press the mode button once. This will erase all of the saved measurements
in memory, but only for the selected mode. That is, performing a reset when in SMPL mode will only erase the
manual measurements and performing a reset when in LOG mode will only erase the automatic measurements.
The LCD display consists of the total number of logged
measurements in the upper right hand corner, the real-time
irradiance value in the center, and the selected menu
options along the bottom.

Review/Download Data: Each of the logged measurements in either SMPL or LOG mode can be reviewed on the
LCD display by pressing the up/down buttons. To exit and return to the real-time readings, press the sample
button. Note that the daily total values are not accessible through the LCD and can only be viewed by downloading
to a computer.
Downloading the stored measurements will require the AC-100 communication cable and software (sold
separately). The meter outputs data using the UART protocol and requires the AC-100 to convert from UART to
USB, so standard USB cables will not work. Set up instructions and software can be downloaded from the Apogee
website (http://www.apogeeinstruments.com/ac-100-communcation-cable/).

Spectral Errors for Measurements with Silicon-cell Pyranometers
Apogee MP series solar radiation meters are calibrated under electric lamps in a calibration laboratory. The
calibration procedure simulates calibration under clear sky conditions at a solar zenith angle of approximately 45°.
However, due to the limited spectral sensitivity of silicon-cell pyranometers compared to the solar radiation
spectrum (see graph below), spectral errors occur when measurements are made in conditions that differ from
conditions the sensor was calibrated under (e.g., the solar spectrum differs in clear sky and cloudy conditions, thus
measurements in cloudy conditions result in spectral error because sensors are calibrated in clear sky conditions).
Silicon-cell pyranometers can still be used to measure shortwave radiation in conditions other than clear sky or
from radiation sources other than incoming sunlight, but spectral errors occur when measuring radiation with
silicon-cell pyranometers in these conditions. The graphs below show spectral error estimates for Apogee silicon-
cell pyranometers at varying solar zenith angles and varying atmospheric air mass. The diffuser is optimized to
minimize directional errors, thus the cosine response graph in the Specifications section shows the actual
directional errors in practice (which includes contributions from the spectral shift that occurs as solar zenith angle
and atmospheric air mass change with time of day and time of year). The table below provides spectral error
estimates for shortwave radiation measurements from shortwave radiation sources other than clear sky solar
radiation.
Spectral response of Apogee SP series
pyranometers compared to solar
radiation spectrum at Earth’s surface.
Silicon-cell pyranometers, such as
Apogee SP series, are only sensitive to
the wavelength range of
approximately 350-1100 nm, and are
not equally sensitive to all
wavelengths within this range. As a
result, when the spectral content of
solar radiation is significantly different
than the spectrum that silicon-cell
pyranometers were calibrated to,
spectral errors result.

Spectral Errors for Shortwave Radiation Measurements with Apogee SP Series Pyranometers
Radiation Source (Error Calculated Relative to Sun, Clear Sky)
Error [%]
Sun (Clear Sky)
0.0
Sun (Cloudy Sky)
9.6
Reflected from Grass Canopy
14.6
Reflected from Deciduous Canopy
16.0
Reflected from Conifer Canopy
19.2
Reflected from Agricultural Soil
-12.1
Reflected from Forest Soil
-4.1
Reflected from Desert Soil
3.0
Reflected from Water
6.6
Reflected from Ice
0.3
Reflected from Snow
13.7
Spectral error for Apogee SP series
pyranometers as a function of
atmospheric air mass, assuming
calibration at an air mass of 1.5.
Spectral error for Apogee SP series
pyranometers as a function of solar
zenith angle, assuming calibration at
a zenith angle of 45°.

APOGEE AMS SOFTWARE
Downloading data to a computer requires the AC-100 communication cable and the free ApogeeAMS software.
The meter outputs data using the UART protocol and requires the AC-100 to convert from UART to USB, so
standard USB cables will not work.
The most recent version of ApogeeAMS software can be downloaded at
http://www.apogeeinstruments.com/downloads/.
When the ApogeeAMS software is first opened, it will
show a blank screen until communication with the meter
is established. If you click “Open Port” it will say
“connection failed.”
To establish communication, make sure the meter is
plugged into your computer using the AC-100
communication cable. To connect click the dropdown
menu button and “COM#” options will appear. For more
details on how to figure out which COM is the right one,
watch our video.
When you have connected to the correct COM#, the
software will say “Connected”.
Click “Sample Data” to view saved sample readings.

“Daily Totals” shows all of the saved Daily Light Integral
(DLI) totals per day.
Click “30 Min Avg” to see the meter’s 99, 30-minute
averages.
To analyze the data, click on “File” and “Save As” to save
the data as a .csv file.
Or, you can highlight the numbers, copy, and paste them
into a blank Excel spreadsheet. Data will need to be
comma delimited.

MAINTENANCE AND RECALIBRATION
Moisture or debris on the diffuser is a common cause of low readings. The sensor has a domed diffuser and
housing for improved self-cleaning from rainfall, but materials can accumulate on the diffuser (e.g., dust during
periods of low rainfall, salt deposits from evaporation of sea spray or sprinkler irrigation water) and partially block
the optical path. Dust or organic deposits are best removed using water or window cleaner and a soft cloth or
cotton swab. Salt deposits should be dissolved with vinegar and removed with a soft cloth or cotton swab. Never
use an abrasive material or cleaner on the diffuser.
Although Apogee sensors are very stable, nominal accuracy drift is normal for all research-grade sensors. To
ensure maximum accuracy, we generally recommend sensors are sent in for recalibration every two years,
although you can often wait longer according to your particular tolerances.
To determine if your sensor needs recalibration, the Clear Sky Calculator (www.clearskycalculator.com) website
and/or smartphone app can be used to indicate the total shortwave radiation incident on a horizontal surface at
any time of day at any location in the world. It is most accurate when used near solar noon in spring and summer
months, where accuracy over multiple clear and unpolluted days is estimated to be ± 4 % in all climates and
locations around the world. For best accuracy, the sky must be completely clear, as reflected radiation from clouds
causes incoming radiation to increase above the value predicted by the clear sky calculator. Measured values of
total shortwave radiation can exceed values predicted by the Clear Sky Calculator due to reflection from thin, high
clouds and edges of clouds, which enhances incoming shortwave radiation. The influence of high clouds typically
shows up as spikes above clear sky values, not a constant offset greater than clear sky values.
To determine recalibration need, input site conditions into the calculator and compare total shortwave radiation
measurements to calculated values for a clear sky. If sensor shortwave radiation measurements over multiple days
near solar noon are consistently different than calculated values (by more than 6 %), the sensor should be cleaned
and re-leveled. If measurements are still different after a second test, email [e-mail]
to discuss test results and possible return of sensor(s).

Homepage of the Clear Sky
Calculator. Two calculators are
available: One for pyranometers
(total shortwave radiation) and
one for quantum sensors
(photosynthetic photon flux).
Clear Sky Calculator for
pyranometers. Site data are
input in blue cells in middle of
page and an estimate of total
shortwave radiation is returned
on right-hand side of page.

TROUBLESHOOTING AND CUSTOMER SUPPORT
Verify Functionality
Pressing the power button should activate the LCD and provide a real-time irradiance reading. Direct the sensor
head toward a light source and verify the irradiance reading responds. Increase and decrease the distance from
the sensor to the light source to verify that the reading changes proportionally (decreasing irradiance with
increasing distance and increasing irradiance with decreasing distance). Blocking all radiation from the sensor
should force the reading to zero.
Battery Life
When the meter is maintained properly the coin cell battery (CR2320) should last for many months, even after
continuous use. The low battery indicator will appear in the upper left hand corner of the LCD display when the
battery voltage drops below 2.8 V DC. The meter will still function correctly for some time, but once the battery is
drained the pushbuttons will no longer respond and any logged measurements will be lost.
Pressing the power button to turn off the meter will actually put it in sleep mode, where there is still a slight
amount of current draw. This is necessary to maintain the logged measurements in memory. Therefore, it is
recommended to remove the battery when storing the meter for many months at a time, in order to preserve
battery life.
Low-Battery Error after Battery Replacement
A master reset will usually correct this error, please see the master reset section for details and cautions. If a
master reset does not remove the low battery indicator, please double check that the voltage of your new battery
is above 2.8 V, this is the threshold for the indicator to turn on.
Master Reset
If a meter ever becomes non-responsive or experiences anomalies, such as a low battery indicator even after
replacing the old battery, a master reset can be performed that may correct the problem. Note that a master reset
will erase all logged measurements from memory.
Step 1: press the power button so that the LCD display is activated.
Step 2: Slide the battery out of the holder, which will cause the LCD display to fade out.
Step 3: After a few seconds, slide the battery back into the holder.
The LCD display will flash all segments and then show a revision number (e.g. “R1.0”). This indicates the master
reset was performed and the display should return to normal.

Error Codes and Fixes
Error codes will appear in place of the real-time reading on the LCD display and will continue to flash until the
problem is corrected. Contact Apogee if the following fixes do not rectify the problem.
Err 1: battery voltage out of range. Fix: replace CR2320 battery and perform master reset.
Err 2: sensor voltage out of range. Fix: perform master reset.
Err 3: not calibrated. Fix: perform master reset.
Err 4: CPU voltage below minimum. Fix: replace CR2320 battery and perform master reset.
Modifying Cable Length
Although it is possible to splice additional cable to the separate sensor of the MP-200, note that the cable wires
are soldered directly into the circuit board of the meter. Care should be taken to remove the back panel of the
meter in order to access the board and splice on the additional cable, otherwise two splices would need to be
made between the meter and sensor head. See Apogee webpage for further details on how to extend sensor cable
length: (http://www.apogeeinstruments.com/how-to-make-a-weatherproof-cable-splice/).