APW Wyott X TREME-1 User manual

1
FOR YOUR SAFETY: Do not store or use gasoline or other ammable vapors and
liquids in the vicinity of this or any other appliance.
WARNING: Improper installation, operation, service or maintenance can cause
property damage, injury or death. Read and understand these instructions
thoroughly before positioning, installing, maintaining or servicing this equipment.
Initial heating of appliance may generate smoke or fumes and must be done in a well ventilated area.
Overexposure to smoke or fumes may cause nausea or dizziness.
APW Wyott® cooking equipment has been engineered to provide you with year-round dependable service
when used according to the instructions in this manual and standard commercial kitchen practices.
APW Wyott Food Service Equipment Company
265 Hobson St. • Smithville, TN 37166
Telephone: [phone] www.apwwyott.com
INSTALLATION AND OPERATING INSTRUCTIONS
Radiant Conveyor Toaster
Model: X*TREME®-1
INTENDED FOR OTHER THAN HOUSEHOLD USE
2M-93100174 REV A 09/18
WARNING: California Residents Only. This product can expose you to chemicals including
chromium which is known to the State of California to cause cancer and birth defects or
other reproductive harm. For more information go to www.P65Warnings.ca.gov.
DESIGNED SMART. BUILT SOLID.®

2
TABLE OF CONTENTS
SECTION ITEM .................. PAGE
1 Important Safety Instructions ...2
2 General Information ..........4
3 Installation Instructions ........4
4 Operation Instructions .........5
5 Cleaning Instructions .........5
SECTION ITEM .................. PAGE
6 Specications ...............6
7 Troubleshooting ..............6
8 Parts List with Exploded View ...7
9 Wiring Diagram ..............9
10 Warranty ..................11
SAFETY PRECAUTIONS
Before installing and operating this equipment be sure everyone involved in its operation is fully trained
and is aware of all precautions. Accidents & problems can result by a failure to follow fundamental
rules and precautions.
Shut o gas ow through the appliance before cleaning or servicing unit.
The following words and symbols, found in this manual, alert you to hazards to the operator, service
personnel or the equipment. The words are dened as follows:
DANGER: This symbol warns of imminent hazard which will result in serious injury
or death.
WARNING: This symbol refers to a potential hazard or unsafe practice, which could
result in serious injury or death.
CAUTION: This symbol refers to a potential hazard or unsafe practice, which may
result in or moderate injury or product or property damage
NOTICE: This symbol refers to information that needs special attention or must be
fully understood even though not dangerous.
1. IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT: Read the following important safety instructions to avoid personal
injury or death, and to avoid damage to the equipment or property.
WARNING: APW Wyott toasters are designed, built, and sold for commercial use.
If positioned where the general public can use them, make sure that all cautions,
warnings, and operating instructions are clearly posted near each unit to insure
proper operation, reduce the chance of personal injury and/or equipment damage.
WARNING: Plug unit into a properly grounded electrical outlet of the correct voltage,
size and plug conguration. If the plug and receptacle do not match, contact a
qualied electrician to determine the proper voltage and size and install the proper
electrical outlet.
WARNING: Unit is not waterproof. Do not submerge in water. Do not operate if it has
been submerged in water. Do not clean the unit with a water jet.

3
WARNING: To avoid any injury, turn the power switch o at the fuse disconnect
switch/circuit breaker or unplug the unit from the power source and allow to cool
completely before performing any maintenance or cleaning.
WARNING: To avoid electrical shock, always unplug the unit before performing
cleaning or maintenance.
WARNING: For safe and proper operation, the unit must be located a reasonable
distance from combustible walls and materials. If safe distances are not maintained,
discoloration or combustion could occur.
WARNING: An earthing cable must connect the appliance to all other units in the
complete installation and from there to an independent earth connection.
WARNING: To avoid electrical shock or personal injury, do not steam clean or use
excessive water on the unit.
WARNING: If service is required on this unit, contact your authorized APW Wyott
Service Agent, or contact the APW Wyott Service Department directly at
[phone] or [phone]; fax [phone].
WARNING: This product has no “user” serviceable parts. To avoid damage to the
unit or injury to personnel, use only Authorized APW Wyott Service Agents and
genuine APW Wyott Parts when service is required.
WARNING: Genuine APW Wyott Replacement Parts are specied to operate
safely in the environments in which they are used. Some aftermarket or generic
replacement parts do not have the characteristics that will allow them to operate
safely in APW Wyott equipment. It is essential to use APW Wyott Replacement Parts
when repairing APW Wyott equipment. Failure to use APW Wyott Replacement
Parts may subject operators of the equipment to hazardous electrical voltage,
resulting in electrical shock or burn.
CAUTION: Some exterior surfaces on the unit will get hot. Use caution when
touching these areas to avoid injury.
CAUTION: Locate the unit at the proper counter height, in an area that is convenient
for use. The location should be level to prevent the unit or its contents from
accidentally falling, and strong enough to support the weight of the unit and food.
WARNING: In Europe, appliance must be connected by an earthing cable to
all other units in the complete installation and thence to an independent earth
connection in compliance with EN 60335-1 and/or local codes
CAUTION: The National Sanitation Foundation (NSF) requires that units over 36” (91
cm) in length or weighing more than 80 lbs. (36 kg) to be either sealed or raised on
the installation surface. If this unit cannot be sealed at the point of use, 4” (10 cm)
legs are included to allow for proper cleaning access below unit.

4
2. GENERAL INFORMATION
1. Overall Dimensions w/Wire Feeder - 13.610”H (34.5cm) x 15.192” W (38.6cm) x 17.982” D (45.7cm)
2. Product Opening - 1.50”H (3.8cm) x 10.50” W (26.7cm)
3. Electrical Requirements (Single phase):
A. 120 Volt, 1800 Watt, 15 Amp.
B. 208 Volt, 1800 Watt, 8.5 Amp.
C. 230/240 Volt, 1800 Watt, 7.8 Amp.
D. Cordset conguration
1. Each toaster equipped with three wire grounded cordset and standard three-prong plug.
2. In the U.S.: 120V uses NEMA 5-15P. 208, 230/240V uses NEMA 6-20P.
3. In Canada: 120V uses NEMA 5-20P.
4. Net/Shipping Weight – 28 lb.(12.7kg) / 33 lb.(14.97kg)
3. INSTALLATION INSTRUCTIONS
1. Check Contents - refer to Figure 1, account for the following parts:
A. Wire Feeder - inside Reector Tray
B. Reector Tray - shipped in place
C. Toast Drawer - shipped in place
D. Instruction Manual - shipped loose
2. Position Wire Feeder
A. Pull out Reector Tray
B. Rotate Wire Feeder
C. Slide Reector Tray back
D. WARNING: Operating toaster without Reector Tray reduces toasting capabilities.
3. Toaster Placement
A. Locate toaster near a grounded receptacle of the proper conguration (see below). Plug the
cordset directly into receptacle (DO NOT USE AN EXTENSION CORD).
1. In the U.S.: 120V uses NEMA 5-15R. 208, 230/240V uses NEMA 6-20R.
2. In Canada: 120V uses NEMA 5-20R.
B. Place toaster on at surface providing following minimum clearances:
1. Base = one inch (provided with legs installed).
2. Side and back walls = two inches
3. Overhead = Enough space to allow adequate heat displacement.
C. Position toaster where customers will not contact any surface labeled “CAUTION HOT”.
CAUTION: Use only non-abrasive cleaners. Abrasive cleaners could scratch the nish
of your unit, marring its appearance and making it susceptible to dirt accumulation.
WARNING: Failure to provide clearances will cause unit failure and invalidate
warranty claims (see installation instructions).
NOTICE: Do not use toppings (butter, etc.) on product as product is inverted during
normal operation.
NOTICE: Operating toaster without legs invalidates any warranty claims.
NOTICE: Neglecting to keep fan opening clean could result in toaster failure.

5
4. OPERATION INSTRUCTIONS
1. Preparation
A. Clean toaster thoroughly before rst use (See cleaning instructions).
B. Controls Familiarity
1. Main Power Switch (located on very bottom of control panel): There are two rocker
switches. The bottom switch powers the unit “ON”. It also turns on the bottom element.
The top switch is a standby switch (upper heat switch) that runs the top element. When the
standby switch is in the “ON” position the unit is at full power. When the standby switch is
in the “OFF” position the unit is running at 50%.
A. Full Power: Flip both rocker switches to the right.
B. Power O: Flip both rocker switches to the left.
2. Conveyor Speed Control: Set knob to the three (3) position for warm-up.
C. Warm-up time: Allow ve (5) minutes.
2. Normal Use
A. Loading Product
1. Place product on Wire Feeder. The conveyor will automatically draw product through the
toaster at a speed determined by conveyor speed control.
B. Toasting Darkness: determined by conveyor speed.
1. Darkest toasting - set conveyor speed control to far left setting.
2. Lightest toasting - set conveyor speed control to far right setting.
3. Other factors aecting toasting darkness.
A. Product moistness - moister product requires slower speeds
B. Sugar content in product - product with more sugar requires slower speeds
C. Product Temperature - cooler product requires slower speeds
4. For best results, use day old bread stored room temperature.
5. CLEANING INSTRUCTIONS
1. Daily Cleaning
A. With toaster o and cool, turn toaster on and set conveyor speed to four.
B. Using a plastic abrasive pad, wipe the conveyor belt in a back and forth motion (side-to-side)
motion to remove baked-on product. Wipe the conveyor belt in the same manner with a hot,
damp cloth.
C. Turn o toaster.
D. Slide the reector/crumb tray out of toaster by pulling forward. Dispose of crumbs and wash
tray in hot, soapy water. Dry tray and place back in toaster.
E. Remove toast drawer from toaster by sliding out and lifting up. Dispose of crumbs and wash
drawer in hot, soapy water. Wipe crumbs from inside the toaster with a hot, damp cloth. Dry
drawer and place back in toaster.
F. Wipe the exterior surfaces of the toaster with a hot, damp cloth.

6
DIMENSIONS – X*TREME®-1
6. SPECIFICATIONS
7. TROUBLESHOOTING
1. Always ask and check the following:
A. Is the unit connected to a live power source?
B. Check the circuit breaker.
C. Is power switch on?
D. Is the unit operating on proper voltage?
2. If problems exist after checking the above, check the chart below.
3. If any service is needed (italicized items), call an APW Wyott authorized service agency. All service
should be performed by an APW Wyott authorized service agency.
PROBLEM CAUSE SOLUTION
Won’t toast... a. Toaster cold. a. Allow ve (5) minutes for warm up.
b. Wrong power switch position. b. Position power switch to full power.
c. Wrong conveyor speed setting. c. Reduce conveyor speed.
Toasts unevenly... d. Only part of product surface is toasted. d. Reduce conveyor speed.
e.Productlocatedtoofartosideofconveyor. e. Place product on conveyor between end links.
Productstickstoconveyororslide. f.Butterorbuttersubstituteusedonproduct. f. Discontinue use of butter or butter substitute.
g.Conveyorsurfacehasbaked-onoilresidue. g.Followdailycleaningmethodstoremove&preventresidue.
h. Very moist or doughy product. h. Use dierent source or day old product.
i. Product not defrosted or thawed. i. Defrost/thaw product.
No power... j. No power to receptacle. j. Check circuit breaker.
k. Toaster unplugged. k. Plug in toaster.
l. Loose connections. l. Check connections.
m. Power switch. m. Check that switch is on & operational.
Won’t heat... n. Loose connections. n. Check connections.
o. Faulty power switch. o. Replace power switch
p. Burnt out element. p. Replace element.
Lighter toast under peak loads... q. Speed control setting. q. Reduce speed control setting.
r. Very moist product. r. Use dierent source or day old product.
s. Product too cold. s. Allow product to warm to room temperature.
t.Toastercavitytemperaturebeingquenched. t. Add 1”or more spacing between product.
Conveyor won’t move... u. No power. u. Check circuit breaker.
v. Conveyor links are binding. v. Check conveyor for bent links.
w.Looseorbadconnectionbetweenspeed
control and conveyor motor.
w. Check for loose or bad connection.
x. Conveyor motor burnt out. x. Replace conveyor motor.
y. Speed control burnt out. y. Replace speed control.

7
EXPLODED VIEW
8. PARTS LIST WITH EXPLODED VIEW
Item P/N Description Qty
1 93100158 RIVET ASSY, XTRM-1 INNER CORE 1
2 93100160 XTRM-1 CONTROL PANEL EXTRUSION 1
3 93100162 XTRM-1 RIGHT SIDE EXTRUSION 1
4 93100150 XTRM-1 TOP COVER LEFT 1
5 93100061 XTRM-1 PANEL, LEFT OUTER 1
6 93100060 XTRM-1 PANEL, RIGHT OUTER 1
7 93000067 END CAP, F/L & B/R 2
8 93000070 END CAP, B/L & F/R 2
9 83267 LEG 1” PLASTIC W/CHROME 4
10 93100058 ASSY, XTRM-1 FEEDER 1
11 93100101 WELD ASSY, XTRM-1 CONTROL PANEL 1
12 70444800 SWITCH, ROCKER ON-OFF 2
13 93100069 XTRM-1 BACK COVER 1
14 81600095 HANDLE, POCKET PULL SERIES 2
15 93100063 XTRM-1 PLATE, CONTROL PANEL 1
16 83221 RHEOSTAT, MOTOR CONTROL 120V 1
83222 RHEOSTAT,MOTORCONTROL208,230/240V 1
17 88705 KNOB 039-266 8A BLACK 1
18 38129 DRAWER TOAST 1
19 93100033 ASSY, ELEMENT HOLDER 2
20 54087 ELEMENT 120V 832W 2
54088 ELEMENT 208V 2
54089 ELEMENT 230/240V 2

8
Item P/N Description Qty
21 93100047 XTRM-1 ELEMENT END CAP 4
22 89061 NUT, HEX 10-24 10
23 83248 BEARING, SHAFT 2
24 83821 BRACKET, BEARING 2
25 38130 ASSY, CLIP BEARING 2
26 38125 BEARING FLANGED POLYMER 2
27 38122 W’ASSY IDLER SHAFT 1
28 89184 BUSHING, .875 HEYCO 2126 1
29 85286 FAN MOTOR COOLING 120V 1
85248 FAN MOTOR COOLING 208, 230/240V 1
30 85152 MOTOR AT10 115V 60HZ 1
85149 MOTOR AT10 208/240V 60HZ 1
85144 MOTOR AT10 230V 60HZ 1
31 89076 WASHER, LOCK 1/4 INTERNAL 4
32 89030 SCREW, 10-32X3/4 4
33 83209 SPROCKET, 23 TOOTH 1/4 PITCH 5/16 BORE 1
34 85287 FAN GUARD 1
35 83956 DRIVE SHAFT ASSY AT-10 SEGMENTED BELT 1
36 83261 SPROCKET, 12 TOOTH 1/4 PITCH 3/8 BORE 1
37 93100064 HEX MACHINE SCREW, #6-32 X 1/4 11
38 89073 SCREW, #8 X 1/2 HEX TAPIT SHT MTLTYPE AB 10
39 82902 CHAIN, 1/4”DRIVE 67 PITCH 1
40 89111 BUSHING, STRAIN RELIEF SR-7W-2 1
41 85638 CORDSET 14/3 600V 5-20P (120V) 1
85640 CORDSET 14/3 600V 5-20P (230&240V) 1
42 PS0018 BELT, WIRE 27x.05 3 SEG. 1
43 89039 SCREW, 8-32X5/16 PH PAN SS 12
44 81600087 SCREW, 8-32 x 3/8, PHILLIPS, PAN HEAD 6
45 89063 NUT, HEX 8-32 4
46 83868 SPACER, CONVEYOR SHAFT 2
47 94000114 SCREW, COUNTERSINK, 6-32X5/16, Z, BLK 12
48 34236 TERMINAL BLOCK END MTG 1
49 34236 TERMINAL BLOCK END MTG 4
50 89054 NUT, KEPS 6-32 2

9
WIRING DIAGRAM
9. WIRING DIAGRAM
IMPORTANT NOTICE: The information contained in this section of the manual
is intended for individuals possessing backgrounds of electrical and mechanical
experience, such as an authorized APW Wyott service technician. APW or the seller
cannot be responsible for the interpretation of this information, nor can it assume
any liability in connection with its use.

10
IMPORTANT FOR FUTURE REFERENCE
Please complete this information and retain this manual for the life of the equipment.
For Warranty Service and/or Parts, this information is required.
Model Number Serial Number Date Purchased
Notes
APW Wyott takes pride in the design and quality of our products. When used as intended and with
proper care and maintenance, you will experience years of reliable operation from this equipment.
To ensure best results, it is important that you read and follow the instructions in this manual carefully.
Installation and start-up should be performed by a qualied installer who thoroughly read,
understands and follows these instructions.
If you have questions concerning the installation, operation, maintenance or service of this product,
contact APW Wyott Foodservice Equipment Company’s “Technical Service Department”.