Aqua Creek Products Pro Pool-XR User manual
Copyright © 2014 Aqua Creek Products All Rights Reserved Revised 11/20/14 V.1.1
PART #: F-004PLB-XR (with anchor)
PART #: F-004PLB-XRNA (without anchor)
US PATENT NUMBER: [D507,769 S] [7,249,386 B2]
350 LB. [159 kg] MAXIMUM WEIGHT CAPACITY
MANDATORY – LEAVE THIS MANUAL WITH LIFT OWNER
Pro Pool-XR Lift
Read & follow all instructions
Lift safety can only be ensured if the lift is installed
and operated according to these instructions
For safety reasons, NEVER swim alone
SAVE a copy of these instructions
NEVER use the lift with a dry pool
NEVER apply direct water pressure to the electronics
NEVER permit children to play on or around the lift
Do not allow children to use the lift without adult supervision
9889 Garrymore Ln
Missoula, MT 59808
888-687-3552 | +1-406-549-0769
aquacreek.com 1
Copyright © 2014 Aqua Creek Products All Rights Reserved Revised 11/20/14 V.1.1
Pro Pool-XR Lift
Table of Contents
PAGE DESCRIPTION
3 PRO POOL-XR COMPONENTS
4 ADA INSTALLATION GUIDELINES
5-6 ANCHOR INSTALLATION: CORE-DRILL RETRO-FIT
7 ANCHOR INSTALLATION: SAW-CUT RETRO-FIT
8 ANCHOR INSTALLATION: NEW CONSTRUCTION
9 PRO POOL-XR LIFT ASSEMBLY INSTRUCTIONS
10 BATTERY MAINTENANCE
11 CARE FOR YOUR LIFT
12-13 PRO POOL-XR LIFT OPERATING INSTRUCTIONS
14-15 TROUBLESHOOTING GUIDE
16 PRO POOL-XR PARTS LIST
17 SEAT & ACTUATOR ASSEMBLY PARTS LIST
18 WARRANTY
2
V.1.1
Copyright © 2014 Aqua Creek Products All Rights Reserved Revised 11/20/14 V.1.1
Pro Pool-XR Pool Lift
Check entire box and inside all packing materials for parts. Before beginning assembly
It is critical all parts be carefully inspected by the installer prior to installation to ensure
no damage occurred in transit and a damaged part is not used. If any damage occurred in
Proper installation cannot be overstressed, as an improper installation voids Aqua Creek’s
READ CAREFULLY
1. THE PRO POOL-XR POOL LIFT W/
LEGREST
2. 24V BATTERY
3. BATTERY CHARGER W/MOUNTING
BRACKET & POWER CORD
4. HANDSET
5. SAFETY BELT
6. ANCHOR JIG PLATE & HARDWARE
(IF ORDERED W/ ANCHOR)
3
Copyright © 2014 Aqua Creek Products All Rights Reserved Revised 11/20/14 V.1.1
Installation: ADA Requirements
ADA REQUIREMENTS:
The Pro Pool-XR Lift is completely ADA Compliant when installed correctly.
The installation must meet the following requirements:
tClear Deck Space Dimensions (see FIGURE 1)
tLift anchors installed between 22 1/2”- 38” from the pool edge
tDeck slope no greater than 1:48
tThe seat must go at least 18” into the water. The lift should be
installed at a location with a water depth of 42”-48”(deck to pool oor)
t Anchor setbacks are based on straight pool/spa walls. Curved pool/spa
walls will eect the anchor setback. Contact Aqua Creek for assistance
FIGURE 1
4
V.1.1
Copyright © 2014 Aqua Creek Products All Rights Reserved Revised 11/20/14 V.1.1
NOTE: FOR DECKS 6”THICK OR MORE, 2500PSI MINIMUM STRENGTH CONCRETE REQUIRED
Required Tools:
Core drill and 1 ½” core drill bit Tape measure
Marking pen Hammer
Cold chisel Torpedo level
Masking tape High strength 2-part construction epoxy*
Black electrical tape (optional)
*Aqua Creek recommends either Hilti™ Brand HIT RE-500-SD or Simpson™ brand SET-XP or equivalent (not included)
continued on page 6
1. Locate the anchor jig-plate, and three (3) anchor bolts with mounting hardware. (If sold
separately from lift, part number F-910SAJP).
2. Using the larger holes in the anchor jig-plate as a template, mark the three hole locations with
a marking pen on the pool deck. Verify the CENTER LINE OF THE ANCHORS are no more than 38
inches from the pools edge. See FIGURE 1, page 4.
3. Using the core drill and the 1 1/2” core drill bit, drill out the three hole locations marked on the
pool deck to a depth of about 4 1/2”.
a. NOTE: Use black electrical tape on the end of the
drill bit as a visual marker to indicate the proper depth needed
to drill to.
b. NOTE: Depending on local grounding requirements,
one hole may need to be drilled larger than the others so
at least one of the anchor inserts is grounded. One anchor insert is
provided with a bonding screw to assist with this step. In some
cases saw cutting a portion of the deck out
completely might be required. In this case, follow the “Saw
Cutting Retro-Fit Instructions”.
4. Remove the core from the holes using a hammer and chisel.
The holes should be completely dry and clear of any debris
before installing the anchors into them.
5. Remove the nuts from the threaded anchor bolts and the black
protective cover from the end of the anchor bolt, exposing the
internal threads that will accept the mounting hardware.
6. Using the smaller holes in the anchor jig-plate, thread the
mounting hardware through the anchor jig-plate holes and
into the ends of the three anchor bolts so the tops of the
bolts are ush with the BOTTOM of the jig-plate (see diagram on left). IMPORTANT: Use the
enclosed packet of anti-seize lube on the threads of the hardware to prevent the hardware from
seizing in the anchor inserts. 5
Copyright © 2014 Aqua Creek Products All Rights Reserved Revised 11/20/14 V.1.1
a. NOTE: It is recommended to apply tape to the bottom of the anchor plate
around the holes so when the epoxy oozes out of the holes it does not
secure the anchor plate to the pool deck.
7. Allow for a way to bond at least one of the anchor inserts according to your local code
requirements. This is typically accomplished with 8-AWG solid-copper wire attached to the
pool’s bonding grid. For more information see NEC Article 680.26.
8. Before putting epoxy into the holes and setting the anchor inserts, test t the anchor inserts in
the pre-drilled holes rst to make sure they line up properly. Pick up the anchor plate with the
three (3) anchor bolts attached to the underside and carefully place them into the three holes
drilled in the deck. Using a torpedo level on the plate, verify the anchor system is level. If they
do not line up you may have to enlarge your holes.
9. After verifying the anchor inserts line up with the holes properly and the anchor assembly is
level, remove the anchor assembly and ll each hole in the pool deck at least half full of two
part construction epoxy (not included). Aqua Creek recommends either Hilti™ Brand RE-500-SD or
an alternative approved adhesive.
10.Pick up the anchor assembly with the three (3) anchor bolts attached to the underside and
carefully place them into the holes drilled in the deck. When placing the anchor bolts attached
to the anchor plate, wiggle the jig-plate assembly a little to make sure the epoxy gets on all
sides of the anchor bolts.
11.Once the anchor bolts are placed into the holes, use a small torpedo level on the anchor plate to
make sure they are level and perpendicular.
12.Allow the epoxy to set up
according to the manufacturer’s
recommendations and remove
the hardware and the anchor
jig-plate. The lift can now safely
mount to the anchors using the
same hardware used to mount the
anchor inserts to the underside of
the anchor jig-plate. The anchor
jig-plate can be recycled or used
for installing a second set of
anchors in another location.
FIGURE 4 6
V.1.1
Copyright © 2014 Aqua Creek Products All Rights Reserved Revised 11/20/14 V.1.1
Bonding Lug
Required Tools:
t Concrete saw with diamond blade
t Tape measure
t 4’ long straight edge or chalk line
t Sledge hammer
t Cold chisel
t Torpedo level
t String line
t Concrete and concrete tools
t #4 Rebar
1. Locate the anchor plate, three (3) anchor inserts with nuts and
mounting hardware). (If sold separately from lift, part number
F-910SAJP).
2. Mark out a section of the pool deck to be removed using a chalk
line or straight edge and a marker. Plan on removing at least a
3’-9” x 3’-9” x 6” section.
3. Using the saw with the diamond blade, make cuts along the
lines previously marked.
4. Using the sledge hammer, break up the concrete within the area
cut and remove the pieces.
5. After the portion of the deck has been removed, verify the new
deck will be able to be at least 6 inches deep.
6. Remove ONE of the nuts from each of the anchor inserts and
place the anchor inserts through the larger holes in the anchor
plate. Thread the nut back on the other side of the anchor insert
so the anchor plate is sandwiched between the nuts. (See FIG 5).
7. Install rebar in the open area of the deck. Tie the rebar into the
existing deck if possible.
8. Set the anchor system in place making sure the center line of the
anchor inserts are no more than 38 inches away from the pool’s
edge.
9. Use the string line or a straight edge to make sure the top of
each anchor bolt is level and ush with the FINISHED deck
surface. Each anchor bolt can be adjusted individually by
turning the nuts with a large wrench.
10. Bond the anchor system using the bonding lug on the anchor
jig-plate. The anchor should be bonded to the pool’s bonding-
grid according to local code requirements. (Reference NEC
Article 680.26).
11. Pour concrete and nish the pool deck surface.
12. Once the concrete has cured, install the lift by aligning the holes
in the lifts base with the anchors installed in the deck. Secure
the lift to the deck using the stainless steel hardware provided.
Be sure to use anti-seize on all hardware.
FIGURE 5
FIGURE 6 7
Copyright © 2014 Aqua Creek Products All Rights Reserved Revised 11/20/14 V.1.1
Anchor Installation: New Construction
For new pool deck installations, the footing for the pool lift should be at least 3’-6” x 3-6” x 6” deep.
It should be reinforced with one mat of four (4) #4 reinforcing bars (rebar) that are 2”clear from
the top of the new pour. (Reinforcing mesh can be used instead of rebar - check the local code
requirements. See drawing below).
FIGURE 7
The footing for the lift should be tied into the rest of the pool deck on three sides with the rebar
or reinforcing mesh. (Do not tie into the bond beam). The rest of the pool deck can be a typical 4”
thick or thickened per local code requirements. Bond rebar or reinforcing mesh grid according to
local requirements and also bond the anchor system to the rebar/mesh grid.
8
V.1.1
Copyright © 2014 Aqua Creek Products All Rights Reserved Revised 11/20/14 V.1.1
1. Attach seat belt to the seat as shown.
2. Install the Pro Pool-XR pool lift onto the three (3) anchors
using the supplied 1/2 x 1-1/2” stainless steel hex bolts and 1/2”
stainless steel at washers. Apply anti-seize to all hardware to
prevent lift from seizing in the anchor. Make sure all bolts are
tight before using the lift.
3. Apply dielectric grease
to the plug terminals.
Plug the handset cable
into the large handset socket on the bottom of the control
box. Press the cord end rmly into the socket until it is
all the way recessed into the socket. Failure to fully push
the remote cord into the socket may result in faulty or
interrupted operation.
4. Before installing the battery, place it on the charging
unit and let it charge for 24 hours. Make sure the orange
“charge” light illuminates when the battery
is being charged.
5. Remove the fully-charged battery from
the charger, grease the terminals, and
install it on top of the Control Box. The
battery will line up square with the control
box, and will‘click’ when it locks in place
properly. The lift will only operate when
the battery is mounted properly.
WHEN NOT IN USE STORE THE BATTERY
ON THE CHARGER. DO NOT LEAVE THE
BATTERY ON THE LIFT WHEN NOT IN USE!
Pro Pool-XR Assembly Instructions
9
Copyright © 2014 Aqua Creek Products All Rights Reserved Revised 11/20/14 V.1.1
Battery Maintenance
1. RECHARGE THE BATTERY AS OFTEN AS POSSIBLE. The battery power unit is a sealed lead
acid battery pack. Frequent recharges will prolong the battery life and maintain a high cold
amperage capacity. THE BATTERY SHOULD BE STORED ON THE CHARGER WHEN NOT IN USE.
2. Do NOT expose the battery to freezing temperatures.
3. Do NOT expose the battery to prolonged periods of extreme heat or severe cold
temperatures.
4. Do NOT expose the battery to long periods of direct sunlight. Heat will shorten your battery
life. Optimum operating temperature is below 20 degrees Celsius (68 degrees F.)
5. Never drop or bump the battery pack. This may result in loose or damaged internal
connections, and may damage the battery terminals.
6. Keep battery terminals clean and free from dirt and corrosion to ensure good contact.
The terminals may be cleaned using alcohol and a cotton swab. Clean oany corrosion or
discoloration of the battery contacts with a Scotch BrightTM pad and then apply dielectric grease
(supplied with lift) as shown in the gure below.
Clean with alcohol
and a cotton swab and
apply dielectric grease
to terminals
10
V.1.1
Copyright © 2014 Aqua Creek Products All Rights Reserved Revised 11/20/14 V.1.1
Proper Care of Pool & Spa Lifts
PROCEDURE DAILY WEEKLY MONTHLY
Wash down lift with fresh water and dry with clean, soft,
non-abrasive cloth
Recharge battery
Run the lift through a complete test cycle to verify it is
functioning properly
Visually inspect lift for damage, corrosion, and loose or
missing hardware
Check all contact points for damage and/or corrosion
Repair, clean, and apply dielectric grease to all contact
points
Thoroughly clean lift frame and apply a liberal coat of car
wax to maintain the lift’s nish
Check all Warning and Cautionary labels to make sure they
are not faded or worn. Replace as needed.
PROPER CARE NOTES
t6TFPOMZGSFTIXBUFSUPXBTIZPVSMJGU%POPUXBTIXJUIQPPMXBUFS
t6TFPOMZDMFBOTPGUOPOBCSBTJWFDMPUITUPXJQFEPXOZPVSMJGU
t%POPUTUPSFMJGUJOQVNQSPPNPSOFBSDIFNJDBMT
t%POPUBMMPXDIJMESFOUPQMBZPOPSBSPVOEUIJTMJGU
t8IFODMFBOJOHUIFMJGUEPOPUTQSBZXBUFSEJSFDUMZPODPOUSPMCPYPSCBUUFSZ
t5IFMJGUNBZOFFEUPCFCPOEFEBDDPSEJOHUPMPDBMDPEFSFRVJSFNFOUT
For service and/or replacement parts contact Aqua Creek Direct at
Toll free: (888) 687-3552
To remove stains wash aected area with mild dish soap. For stubborn spots and stains
try using soft scrub with some brisk rubbing. Use white epoxy paint to touch up. Apply
wax to nish.
STAIN REMOVAL TIPS:
11
Copyright © 2014 Aqua Creek Products All Rights Reserved Revised 11/20/14 V.1.1
3
Lower Armrests
1
Flip Up Armrests
4
Secure Lapbelt
2
Transfer to Lift
Pro Pool-XR Operation Instructions
12
V.1.1
Copyright © 2014 Aqua Creek Products All Rights Reserved Revised 11/20/14 V.1.1
5
Lower Lift by Applying
Pressure to the Down Arrow
6
Release Pressure from Button
to Stop, Then Release Lapbelt
7
Return to Submerged Lift
Seat & Secure Lapbelt
8
Raise Lift by Applying
Pressure to the Up Arrow
9
Release Lapbelt, Raise
Armrests, & Exit Lift Seat 13
Copyright © 2014 Aqua Creek Products All Rights Reserved Revised 11/20/14 V.1.1
Troubleshooting Guide
Problem: The lift won’t move when the handset button is pressed.
2) Make sure the cords are properly plugged in:
Check the ends of the cords for corrosion or damage. The cord plugs
should be recessed into the outlet. You should feel them pop into
place when they are correctly inserted.
Solution:
1) Make sure the Battery is properly seated:
You should hear a click when the
battery is properly seated on the
control box or charger.
Click!
NOT Properly Attached:
Note: the white bracket is
in front of the silver clip,
which will not allow for an
electrical connection
Properly Attached:
Note: the white bracket
is behind the silver clip,
holding it securely to allow
for an electrical connection
NOT Properly Inserted:
The cord plug is ush with or
sticking out of the outlet
Properly Inserted:
The cord plug is recessed
into the outlet
POP!
14
V.1.1
Copyright © 2014 Aqua Creek Products All Rights Reserved Revised 11/20/14 V.1.1
The Charger is ON
when the green light
is glowing
The Battery is
CHARGING when the
orange light is glowing
When the Battery is
charged, the orange
light will stop glowing
Troubleshooting Guide (CONTINUED)
4) Make sure the Battery is fully charged:
3) Check the contact points:
Make sure the contact points of the control box
and the battery are not damaged or corroded.
If there is corrosion, clean with Scotch-BriteTM
pad. Put some dielectric grease on the contact
points before reattaching the battery.
Problem: The lift stopped moving over the water and is stuck.
Solution:
1) Press the Emergency button
Use a pen or pencil tip and stick it into the
emergency button on the front of the control
box to retract the lift.
Note: the lift will not retract if the battery is
not fully charged or if the control box is not
working. The emergency button only overrides
the remote handset.
15
Copyright © 2014 Aqua Creek Products All Rights Reserved Revised 11/20/14 V.1.1
Pro Pool-XR Parts List
Item # QTY PART # DESCRIPTION
1 1 STL-10A-10 PP-XR T-BASE ASSEMBLY
2 1 STL-10B-10 PP-XR B-BASE ASSEMBLY
3 2 STL-111-01 PP-XR BASE SPACER PLATE
4 1 STL-200-00 PP-XR FRAME ASSEMBLY
5 1 A-2012ARM-STL PP-XR CHAIR CRADLE ASSEMBLY
6 1 STL-WMA-00 PP-XR SEAT SUPPORT PART A
7 1 STL-WMB-00 PP-XR SEAT SUPPORT PART B
8 1 L-2014FBL-STL PP-XR CONTROL ARM
9 1 A-8980PPAF-AT2 PRO POOL ACTUATOR ASSEMBLY
10 1 SA-0904CA 18” CHAIR ASSEMBLY
11 1 F-105LAR LEGREST ASSEMBLY
12 2 BOLT, 1/4 X 3/4 HWH, SS 1/4”-20 X 3/4” HEX WASHER-HD, SS
13 2 BOLT, 5/16 X 2 HCS 5/16”-18 X 2” HEX BOLT, SS
14 2 BOLT, 5/16 X 4 HCS 5/16”-18 X 4” HEX BOLT, SS
15 9 FLAT WASHER, 5/16 SS 5/16” FLAT WASHER, SS
16 5 NYLOCK, 5/16 SS 5/16”-18 NYLOCK NUT, SS
17 2 BOLT, 3/8 X 5 1/2 HCS 3/8”-16 X 5 1/2”HEX BOLT, SS
18 1 BOLT, 3/8 X 1 3/4 SHOULDER 3/8” X 1 3/4” SHOULDER BOLT, SS
19 4 FLAT WASHER, 3/8 SS 3/8” FLAT WASHER, SS
Item # QTY PART # DESCRIPTION
20 2 NYLOCK, 3/8 SS 3/8”-16 NYLOCK NUT, SS
21 2 FLAT WASHER, 1/2 SS 1/2” FLAT WASHER, SS
22 2 NYLOCK, 1/2 SS 1/2”-13 NYLOCK NUT, SS
23 2 BOLT, 5/8 X 1 1/2 HCS 5/8”-11 X 1 1/2” HEX BOLT, SS
24 1 BOLT, 5/8 X 6 HCS 5/8”-11 X 6”HEX BOLT, CUSTOM
25 2 FLAT WASHER, 5/8 SS 5/8” FLAT WASHER, SS
26 3 NYLOCK, 5/8 SS 5/8”-11 NYLOCK NUT, SS
27 1 NYLOCK, 3/4 SS 3/4”-10 NYLOCK NUT, SS
28 2 TT-1001-1 7/8” X 1/2”X 1/8”THRST WSHR, SS
29 2 MACH-BUSHING, 7/8 X 5/8 X 1/4 5/8” X 7/8” X 1/4” CUSTOM BUSHING
30 1 TT-1205-1 1 1/4” X 3/4” X 1/8”THRST WSHR, BZ
31 2 FL-50-3 1/2” X 5/8” X 3/8” FLNG BRNG, BZ
32 2 FL-64-6 5/8” X 7/8” X 3/4” FLNG BRNG, BZ
33 1 MACH-BUSHING 7/8 X 3/4 X 1/4 3/4”X 7/8” X 1/4” CUSTOM BUSHING
34 2 FL-75-6 3/4” X 7/8” X 3/4” FLNG BRNG, BZ
35 3 SQR-1-14-20 1”SQUARE PLASTIC CAP, BLACK
36 4 SQR-2-10-14 2”SQUARE PLASTIC CAP, BLACK
37 3 RER50X100MM 2” X 4” RECT. PLASTIC CAP, BLACK
38 1 F-045AC WATER RESISTANT ACTUATOR CVR
16
V.1.1
Copyright © 2014 Aqua Creek Products All Rights Reserved Revised 11/20/14 V.1.1
Seat Assembly Parts List
Actuator Assembly Parts List
ITEM # QTY PART # DESCRIPTION
1 1 P-900-B CHAIR, 1ST MOLD (OLD), BLUE
2 2 P-2100FLA-88 ARMREST TUBE
3 1 P-1208HSB HANDSET BRACKET, HDPE
4 2 RUBBER HAND GRIPS RUBBER HAND GRIPS, BLACK
5 1 LANYARD SS LANYARD FOR FOOTREST PIN
6 1 COTTER PIN, 1/4 X 3 1/4 1/4” X 3 1/4” QUICK-PULL PIN FOR FOOTREST
7 4 FLAT WASHER, 1/4 SS 1/4” FLAT WASHER, SS
8 2 NYLOCK, 1/4 SS 1/4”-20 NYLOCK NUT, SS
9 1 SCREW, #10 X 3/4 PHSMS #10 X 3/4” PAN-HD SMS, SS
10 2 SCREW, #6 X 1/2 PHSMS #6 X 1/2” PAN-HD SMS, SS
11 2 SCREW, #12 X 3/4 FHSMS #12 X 3/4” FLAT-HD SMS, SS
12 2 RUBBER BUMPER, 3/8 3/8” RUBBER BUMPER, BLACK
13 2 F-38SB SEAT BELT 2” BLACK WITH VELCRO
14 2 BOLT, 1/4 X 3 1/4 BHSCS 1/4”-20 X 3 1/4” BUTTON-HD SCS, SS
Item # QTY PART # DESCRIPTION
1 1 PFH-100-00 PRO POOL H-FRAME ASSEMBLY
2 1 340461-00 600mm LA-34 ACTUATOR
3 1 CBJ2001NA001381 1-CHANNEL CONTROL BOX
4 1 MBJ2-01 MOUNTING BRACKET, CB/BATTERY
5 1 M5 X 10 LPCS M5 X 10mm LOW-PRO CAP SCREW
6 1 BAJ100000291 24V BATTERY W/ ACP LOGO
7 1 SET SCREW, 1/4 X 3/8 1/4”-20 X 3/8” SET SCREW, SS
8 1 BOLT, 3/8 X 1 1/4 SHOULDER 3/8” X 1 1/4”SHOULDER BOLT, SS
9 1 NYLOCK, 5/16 SS 5/16”-18 NYLOCK NUT, SS
10 2 HOSE CLAMP, 1 3/4 SS 1 3/4” HOSE CLAMP, SS
11 1 FLAT WASHER, #10 SS #10 FLAT WASHER, SS
17
Copyright © 2014 Aqua Creek Products All Rights Reserved Revised 11/20/14 V.1.1
Aqua Creek Products, LLC Limited Lifetime Warranty:
Pro Pool-XR Lift
Aqua Creek Products lifts have a Limited Lifetime Warranty
warrants to the original end user that all non-frame components manufactured by Aqua Creek, when properly installed in accordance with assembly and installation
provided that Aqua Creek receives prompt notice in writing of any defect or failure and satisfactory proof thereof, with the following exceptions:
Exception: All electrical components, including the linear actuator shall have the following warranty period:
Year 1-2: 100% Coverage
To initiate a warranty claim, the owner of an Aqua Creek product must provide the place of purchase, in writing, with a full description of the product, its serial number,
THE WARRANTIES SET FORTH HEREIN ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, WHICH ARE HEREBY DISCLAIMED AND EXCLUDED, INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY
THE SOLE AND EXCLUSIVE REMEDIES FOR BREACH OF ANY AND ALL WARRANTIES WITH RESPECT TO THE PRODUCTS SHALL BE LIMITED TO REPAIR OR REPLACEMENT AT AQUA CREEK’S DESIGNATED FACTORY LOCATION, OR DULY
IN NO EVENT SHALL AQUA CREEK PRODUCTS, LLC BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, INDIRECT, PUNITIVE OR EXEMPLARY DAMAGES OR LOST PROFITS FROM ANY BREACH OF THIS LIMITED WARRANTY OR
Aqua Creek Products, LLC
9889 Garrymore Lane
Missoula, MT 59808
Toll Free: (888) 687-3552
Local/Intnl: (406) 549-0769
18
sales@aquacreek.com | www.aquacreek.com+1-406-549-0769 | 888-687-3552
ACCESSORIES
F-019CA
Cycle Attachment
Ranger with headrest and
pull-out leg rest options
F-706RLSS
Sling Seat Assembly
F-705
Wheelchair Attachment
ACCESSORIES & OPTIONS
F-019CA Cycle Attachment
F-105LAR Pull-Out Legrest
F-422PLH Headrest (Old Pro Pool)
F-422PLH-2
F-422XR
Headrest (All other lifts)
Headrest (Pro Pool-XR)
F-423CS Chest Strap
F-414OHB Overhead Therapy Bar
F-705 Wheelchair*
F-734RSA Spineboard*
F-736HS Head Immobilizer For
Spineboard*
F-730RSA Gurney*
F-706RLSS Sling Seat Assembly*
*For Revolution & Titan Only
Ranger
with overhead therapy bar
sales@aquacreek.com | www.aquacreek.com+1-406-549-0769 | 888-687-3552
ACCESSORIES
UPGRADE PACKS
F-004PLBAP Ranger/Pro Pool + Transport Cart
F-900PLAP Pathnder + Transport Cart
F-920SAP Pro Pool XR + Transport Cart
F-800SCAP Scout
F-700RLAP Revolution/Titan
F-12PPAP Patriot/Portable Pro Pool
F-03EZPLAP EZ
(sling bars, rigid seat sling w/ seat belt, cover)
F-03PEZAP Power EZ (sling bars, rigid seat sling w/
seat belt, cover, extra battery)
F-190PHBLAP Super Power EZ (sling bars, rigid seat
sling w/seat belt, cover, extra battery)
COVERS
F-442BL-C Ranger/Pro Pool
F-12BL-C Pro Pool XR/Pathnder/Patriot/
Portable Pro Pool
F-450BL-C Scout
F-720BL-C Revolution/Titan
F-EZBL-C EZ/Power EZ
F-440HBC-B Super Power EZ
F-440EZHSC EZ/Power EZ
(cover w/hardseat option)
F-445SLC Spa/Pro Spa 40 Series
F-460PSLC Pro Spa 60 Series
F-004PLBAP
Upgrade Pack
UPGRADE PACKS INCLUDE**
Lift Cover
Extra Battery
Headrest
Chest Strap
**For lifts EXCEPT the EZ series. See table for
EZ series upgrade pack specics.
TRANSPORT CARTS
F-428HT Ranger/Pro Pool/Pathnder
F-914STC Pro Pool XR
F-814SCTC Scout
F-714RTC Revolution
F-614TTC Titan
F-423CS
Chest Strap
F-428HT
Transport Cart
This manual suits for next models
2
Table of contents
Other Aqua Creek Products Lifting System manuals
Aqua Creek Products
Aqua Creek Products Ranger 2 User manual
Aqua Creek Products
Aqua Creek Products Patriot-AT1 User manual
Aqua Creek Products
Aqua Creek Products Pro Pool-AT User manual
Aqua Creek Products
Aqua Creek Products Scout Series User manual
Aqua Creek Products
Aqua Creek Products Scout Hi F-802SCNA-HLD User manual
Aqua Creek Products
Aqua Creek Products Power EZ 2 User manual
Aqua Creek Products
Aqua Creek Products F-03EZPLNA Installation instructions
Aqua Creek Products
Aqua Creek Products F-194PHBL-NA User manual
Aqua Creek Products
Aqua Creek Products SPA LIFT ULTRA User manual
Aqua Creek Products
Aqua Creek Products EZ Series User manual
Aqua Creek Products
Aqua Creek Products Scout 2 User manual
Aqua Creek Products
Aqua Creek Products F-423CS User manual
Aqua Creek Products
Aqua Creek Products PRO POOL LIFT F-004PLB-R User manual
Aqua Creek Products
Aqua Creek Products Revolution Spa Lift User manual
Aqua Creek Products
Aqua Creek Products F-702RLNA-SPA-01 User manual
Aqua Creek Products
Aqua Creek Products PRO POOL-AT REVERSE User manual
Aqua Creek Products
Aqua Creek Products Patriot-AT1 User manual
Aqua Creek Products
Aqua Creek Products F-004PLB-XR-R User manual
Aqua Creek Products
Aqua Creek Products F-714RTC User manual
Aqua Creek Products
Aqua Creek Products Power EZ 2 User manual
Popular Lifting System manuals by other brands
BHW
BHW WHP08 Operating & maintenance instructions
Sav
Sav SAV 531.42 operating instructions
probst
probst AKZ-UNI-850 operating instructions
Challenger Lifts
Challenger Lifts EW0820 Installation, operation & maintenance manual
Liko
Liko Uno 102 Instructions for use
stellar labs
stellar labs Slider50 owner's manual
Nibotechnics
Nibotechnics Autolift electric installation instructions
WIRTH
WIRTH OKTOPUS GLASS-Jack GL-CC 1200 operating instructions
LSI-Robway
LSI-Robway RCI-1502 LM instruction manual
Böcker
Böcker Toplift operating instructions
John Bean
John Bean 40HP210ES instruction manual
LGMG
LGMG T65J Maintenance manual