Aqua Creek Products F-710RLA User manual

Copyright © 2018 Aqua Creek Products All Rights Reserved Revised 9/14/18
Revolution
Anchor
9889 Garrymore Ln
Missoula, MT 59808
888-687-3552 | [phone]
www.aquacreek.com
PART #: F-710RLA
MANDATORY
LEAVE THIS MANUAL WITH LIFT OWNER
Read and follow all instructions.
Lift safety can only be ensured if the lift is installed and
operated according to these instructions.
• NEVER permit children to play on or around the lift
• Do not allow children to use the lift without adult
supervision
• NEVER apply direct water pressure to the electronics
• NEVER use the lift with a dry pool
Check entire box and all packing materials for parts. Before beginning assembly, read the
instructionsandidentifypartsusingtheguresandpartslistedinthisdocument.
It is critical that all parts be carefully inspected prior to installation. If any damage occurred in
transit,AquaCreekProducts,LLCmustbenotiedwithinthreedaysofreceiptofunit.
Proper installation cannot be overstressed, as an improper installation voids Aqua Creek’s
warranty and may affect the safety of the user.
READ CAREFULLY
1

Copyright © 2018 Aqua Creek Products All Rights Reserved Revised 9/14/18
Parts List
ITEM # QTY PART # DESCRIPTION
1 1 RVA-110-01 REVOLUTION ANCHOR TUBE, BRONZE
2 1 SCA-10P-00 ANCHOR PLUG
3 1 F-710RLA-CAP ANCHOR CAP, REVOLUTION
4 1 GBL-4DB LUG, IN GROUND GROUNDING LUG
5 1 ROLL PIN, 1/8”X1” ROLL PIN, 304 SS, 1/8” X 1”
6 1 BSH 10 X 3/4 BOLT, 316 SS, 10-24 X 3/4”, SHCS
7 1 F-ACTOOL ANCHOR CAP TOOL
3
1
5
2
4
6
7
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 RVA-110-01
REVOLUTION 8" ANCHOR TUBE,
BRONZE
1
2
SCA-10P-00
HDPE, PLUG, 2" SOLID ROUND,
SCOUT 10"
1
3 F-710RLA-CAP REVOLUTION ANCHOR CAP 1
4
GBL-4DB LUG, IN GROUND GROUNDING
LUG
1
5
ROLL PIN, 1-8 X 1 ROLL PIN, 304 SS, 1/8" X 1" 1
6
BSH 10 X 3-4 BOLT, 316 SS, 10-24 X 3/4 SHCS 1
7
F-ACTOOL ANCHOR CAP TOOL 1
2

Copyright © 2018 Aqua Creek Products All Rights Reserved Revised 9/14/18
Installation: ADA Guidelines
16"
MIN.
[40.6 cm]
48"
[122 cm]
36"
[91.4 cm]
29"
[73.7 cm]
[172.5cm]
68"
[30.5cm]
12"
ADA
REQUIRED
CLEAR DECK
SPACE
DECK
WATER POOL WALL
FIGURE 1
ADA Requirements:
The Revolution Lift is ADA Compliant.
The installation must meet the following requirements:
• Clear deck space dimensions (see FIGURE 1)
• Installed a minimum of 16 inches from the pool wall
• Deck slope no greater than 1:48
• The seat must submerge at least 18 inches into the water. The lift should be installed at a location with
42inches-48inchesofdepth(decktopooloor)
• Anchor setbacks are based on straight pool/spa walls. Curved pool/spa walls will effect the anchor setback.
3

Copyright © 2018 Aqua Creek Products All Rights Reserved Revised 9/14/18
Anchor Installation: New Construction or Retro-Fit
You may need to saw cut and remove a portion of an existing pool deck in order to achieve the 10 inch depth
footing requirement. Aqua Creek does NOT recommend a core drill installation for this lift.
To properly install this anchor, you will need to have a concrete footing comprised of 2500 psi concrete that is
10 inches deep and 4 feet - 3 inches square and reinforced with rebar. Refer to Figures A and B below.
If cutting into an existing pool deck, the rebar must be drilled and secured to the surrounding pool deck on
three sides (do not secure into bond beam). The centerline of the anchor should be no less than 9 inches from
the edge of the footing.
NOTE: The anchor setback will vary depending on application and any options you choose for the lift. 16 inch
setback is the minimum for ADA compliance however, given a typical 1 foot bond beam and the fact that the
anchor should be no closer than 9 inches to the edge of your footing, 21 inches may be the closest you can
achieve. The chart below outlines the minimum and maximum anchor setback locations for the available op-
tions based on this premise. Also, some attachments will de-rate the lifting capacity of the lift. Refer to the
attachment manual or spec sheet to check for changes in lifting capacites.
1. Determine the location for the anchor based on the options you are ordering or think you may order in the
future and set the anchor in place. You may use a small mass of wet concrete to set the anchor in place.
Usealevelandstringlinestomakesuretheanchorisperpendicularandwillbeushwiththetopofthe
nisheddecksurface.
2. Bond the anchor according to local code requirements using the bonding lug on the bottom of the anchor.
ReferencetheNationalElectricCode(NEC)Article680.26forspecicsonbonding.
3. PourtheconcretesothatthetopoftheanchorwillbeushwiththeFINISHEDpooldecksurface.
4. Once the concrete has cured, the lift can be put into place.
ITEM NO. OPTION MIN MAX
F-730RSA-S2 GURNEY 21” 32”
F-706RLSS SLING SEAT 21” 24”
F-734RSA SPINE BOARD 21” 34”
F-705-S2 WHEELCHAIR ADAPTER 21” 34”
4'-3"
2'-1
1
2
"
9"
MIN
1'-0"
MIN.
1'-9" MIN.
3'-0" MAX.
4'-3"
4'-3"
3"
CLR
81
2
"
10"
2"
CLR
EPOXY TOP MATT
TO EXISTING SLAB
(4" MIN. EMBED)
REVOLUTION
BRONZE ANCHOR
SLEEVE
4'-3" SQ. x 10" DEEP
CONC. FTG. W/5 - #5
E.W., TOP & BTM. &
#4 U BAR @ TOP
(SEE FIGURE B)
DECK
POOL
WALL
FIXING
ANCHOR
FIXING
ANCHOR
LOCKING-PIN
SLOT
2'-0"
2'-0"
1'-0"
FIGURE A
FIGURE B
4

Copyright © 2018 Aqua Creek Products All Rights Reserved Revised 9/14/18
ADA Fixing Insert Installation (Commercial Applications)
1. Werecommendinstallationofthexinginsertaftertheconcretehascuredandyouarereadytoinstallthe
lift into the anchor.
2. Place the main assembly in the anchor. DO NOT LIFT THE MAIN ASSEMBLY BY USING THE ELECTRIC RAM
AS A HANDLE. If the transport cart was ordered with the lift, it can be used effectively here. If not, use two
people.
3. Markthelocationforthexinganchorholeandremovethelift. (see pg 4, FIGURE A)
4. Drill the hole with a 1 1/4 inch core drill or roto-hammer to a depth of about 4 1/2 inches.
5. Cleantheholeoutandmakesureitisdry.Threadthe1/2inchboltintothetopofthePVCxinganchor
andtestttoverifyitcanbemountedperpendicular.SeeStep1below.
6. Usingatwopartconstructionepoxy,lltheholeapproximatelyhalffullandcarefullyinsertthePVCxing
anchor into the hole, twisting as you push down to evenly spread the epoxy.
7. Allow the epoxy to cure before securing the lift.
8. Re-install the lift into the anchor and using the 1/2 inch bolt and washer, carefully thread into the installed
anchor until snug. TO PREVENT BREAKING THE FIXING BRACKET, DO NOT OVERTIGHTEN!
DECK
MAIN ASSEMBLY
POST
ANCHOR
1/2" X 2"
HEX BOLT
1/2" FLAT
WASHER
STEP 1
5