AQUATROL 69 Manual

USING A PROPER SIZED WRENCH, REMOVE THE HOOD (11)
LOOSEN THE LOCK NUT (14) (THEIR IS NO LOCK NUT ON 1/2''
AND 3/4'' VALVES)
ADJUST THE PRESSURE SCREW (12)
INCREASE PRESSURE BY TURNING CLOCKWISE
(TIGHTEN).
DECREASE PRESSURE BY TURNING COUNTER-CLOCKWISE
(LOOSEN).
AFTER THE DESIRED PRESSURE IS OBTAINED, TIGHTEN
THE LOCK NUT (14)
REINSTALL THE HOOD (11)
DO NOT OVER TIGHTEN & ONLY USE PROPERLY SIZED
WRENCHES THROUGHOUT.
FLOW RATE NOTATION:
THE FLOW RATE CHANGES BASED ON THE ADJUSTMENT OF PRESSURE SETTINGS. LESS PRESSURE INCREASES
FLOW RATE / MORE PRESSURE (HIGHER) DECREASES THE FLOW RATE OR GPM.
Figure No. 69
Adjustable Relief Valve
Installation & Operating Instructions
WHEN INSTALLING (OR ADJUSTING) THIS VALVE:
USE ONLY THE PROPER SIZED HEX WRENCH FOR ALL FITTINGS.
IF USING PIPING COMPOUND OR TAPE, DO NOT APPLY TO
THE BOTTOM FEW THREADS AS THE PRESENCE OF ANY FOREIGN OBJECTS
WITHIN THE VALVE CHAMBER COULD AFFECT THE PERFORMANCE OF THIS
PRODUCT.
THE VALVE IS AVAILABLE IN PRESSURE SETTINGS FROM
5 PSI TO 600 PSI
PRESSURE SETTINGS ARE BASED ON THE SPRING RANGES.
(CONTACT AQUATROL FOR SPECIFICATIONS)
THE PRESSURE RANGE IS INDICATED ON THE NAMEPLATE ATTACHED TO
THE VALVE BODY.
oNOTE- THE VALVE SHOULD BE ADJUSTED USING A PRESSURE
GAUGE WITHIN THE STAMPED RANGE ON THE VALVE.
ADJUSTMENT OUTSIDE OF THE PRESSURE RANGE CAN CAUSE
THE VALVE TO BE COMPLETELY CLOSED OFF RESULTING IN
SEVERE OVERPRESSURE.
Customer Support/Service: 630-365-5434 Or Toll Free 1-800-365-5400
www.aquatrol.com
ADJUSTMENT PROCEDURE:

USING THE PROPER SIZED WRENCH REMOVE THE HOOD (11)
LOOSEN THE PRESSURE SCREW LOCK NUT (14) (THEIR IS NO LOCK
NUT ON 1/2" AND 3/4" VALVES)
LOOSEN THE PRESSURE SCREW (12) (COUNTER-CLOCKWISE)
REMOVE THE BONNET (2) FROM THE BODY (1)
•PLACE THE HEX OF THE BODY (1) INTO A VISE
•SCREW A FITTING INTO THE OUTLET OF THE BONNET (2)
•USE A PIPE AND LOOSEN THE BODY (1) FROM THE
BONNET (2)
ONCE THE BODY (1) IS FREE FROM THE BONNET (2) REMOVE THE
DISC (4) FROM THE BODY (1)
USING A RAG WIPE DOWN THE SEATING SURFACE ON THE BODY
(1) AND DISC (4)
IF POSSIBLE USE A 400 GRIT LAPPING COMPOUND AND RE-LAP THE
BODY (1) AND DISC (4) TOGETHER
•PLACE LAPPING COMPOUND ON SEATING SURFACE OF THE
BODY (1)
•PLACE THE DISC (4) INTO THE BODY (1)
•APPLY LIGHT PRESSURE, HOLD THE DISC (4) STATIONARY
AND SPIN THE BODY (1) ONTO THE DISC FOR 2 MINUTES
REMOVE THE BODY (1) AND DISCC (4) FROM EACH OTHER AND WIPE
CLEAN ANY LAPPING COMPOUND RESIDUE
THE LAPPED AREAS ON THE DISC (4) AND BODY (1) SHOULD BE
FREE OF ANY PREVIOUS MARKS, IF THERE ARE MARKS LEFT LAP
AGAIN
REASSEMBLE THE VALVE AND THEN ADJUST YOUR PRESSURE
ACCORDNGLY
PLEASE SEE THE FRONT OF THIS SHEET FOR PRESSURE
ADJUSTMENT INSTRUCTIONS
NOTE- IF THERE ARE ANY LARGE GOUGES ON THE SEATING
SURFACE, MACHINING OR NEW PARTS WILL BE REQUIRED
FLOW RATE NOTATION:
THE FLOW RATE CHANGES BASED ON THE ADJUSTMENT OF PRESSURE SETTINGS. LESS PRESSURE INCREASES
FLOW RATE / MORE PRESSURE (HIGHER) DECREASES THE FLOW RATE OR GPM.
Customer Support/Service: 630-365-5434 Or Toll Free 1-800-365-5400
www.aquatrol.com
Figure No. 69
Adjustable Relief Valve
Disassembly and Re-Lapping Instructions
PROCEDURE: