Arbor Technology HiCORE-i35Q User manual

- 1 -
Quick Installation Guide
Version 1.3
If you have any technical difculties, please consult the user's manual rst at:
ftp://ftp.arbor.com.tw/pub/manual
Please do not hesitate to call or e-mail our customer service when you still can not
nd out the answer.
http://www.arbor.com.tw
E-mail: [e-mail]
♦ Technical Support
HiCORE-i35Q
PICMG 1.0 Full size SBC
CPU
Intel LGA775 socket for
Core™ 2 Quad/ Core™ 2
Duo Processor
Copyright® 2012 All Rights Reserved. 4041003500130P
Declaration of Conformity
FCC Class A
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions : (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Form Factor
PICMG 1.0 Full size SBC
Chipset
Intel Q35
ICH9
LAN
Realteck RTL8111B
Gigabit Ethernet
I/O
PCI/ ISA/ USB/ IDE/ COM/
FDD/ SATA
Video
Analog RGB
Audio
HDA link

- 2 -
Form Factor PICMG 1.0 Full size SBC
Processor
Supports socket LGA775 for Intel® Core™ 2 Quad/
Core™ 2 Duo / Conroe-L/ Conroe/ Wolfdale LGA775
Processor, FSB 800/1066/1333MHz
Chipset Intel Q35 + ICH9
System Memory Two 240-pin DDR2 DIMM Sockets up to 4GB SDRAM,
667/800MHz
VGA Controller Integrated with Intel® Graphics Media Accelerator 3100
Ethernet One Realtek RTL8111B PCIe GbE controller
BIOS AMI PnP Flash BIOS
I/O Controller ITE-IT8718F
Audio Supports Audio Daughter Board via connector
Serial ATA 2 x Serail ATA ports with 300MB/s HDD transfer rate
IDE Interface 1 x IDE port connector supports 1 device
Serial Port 2 COM ports (COM1: RS-232, COM2: RS-232/422/485
selectable)
Floppy 1 x Floppy Drive Disk
Keyboard / Mouse 1 x Mini-DIN Keyboard and Mouse connector
Universal Serial Bus 12 x USB port 2.0 compliant
Watchdog Timer 255-Level Reset
DIO 4-bit Digital Input / 4-bit Digital Output
IrDA 1 x IrDA connector
Security Support TPM Daughter Board via connector
Operation Temp. 0oC - 60oC (32oF ~ 140oF)
Power Connector 4-pin ATX12V type and ATX Feature
Dimension (L x W) 338 x 122 mm (13.3” x 4.8”)
Specifications
Ordering Information
HiCORE-i35Q Full-Size Intel Core 2 Quad/ Core 2 Duo LGA775 SBC
with Q35, VGA, SATA, Gigabit LAN
FCDB-1111 HD Audio Daughter Board

- 3 -
Before you begin installing your single board, please make sure that the
following materials have been shipped:
Packing List
1 x HiCORE-i35Q PICMG 1.0 full size SBC
1 x Driver CD
1 x Quick Installation Guide
Cable Kit
CBK-06-035Q-00
1 x COM port at cable
1 x FDD at cable
1 x IDE at cable
1 x SATA cable
1 x USB cable
1 x Keyboard & Mouse cable
4 x Mini Jumper 2.54mm
If any of the above items is damaged or missing, contact your vendor
immediately.
The Installation Paths of CD Driver
Windows 2000 & XP
Driver Path
CHIPSET \CHIPSET\INF 8.4
LAN \ETHERNET\REALTEK\8111_WINXP_5764
VGA \GRAPHICS\INTEL_2K_XP_32\1432
Windows 7
Driver Path
CHIPSET \CHIPSET\INF 8.4
LAN \ETHERNET\REALTEK\8110SCL_Win7_7037
VGA \GRAPHICS\INTEL_WIN7_32\1930

- 4 -
Jumpers/ Connectors Quick Reference
Connectors
Label Description
ATX12V1 ATX 12V Connector
JFRT1 Switches and Indicators
CPUF1 CPU Fan Power Connector
SYSF1, SYSF2 Fan Power Connector
EATX1 ATX Feature Connector
TPM1 Trusted Platform Module Connector
CN3 AUDIO connector
SATA1~2 Serial ATA Connectors
COM1 RS-232 Connector
FDD1 FDD Connector
IDE1 IDE Connector
DIO1 Digital I/O Connector
USB2~6 USB Connector
IR1 Infrared Connector
EKB1 External Keyboard Connector
COM2 RS-232/422/485 Connector
KBM1 Keyboard & Mouse
VGA1 Aalog RGB Connector
LAN1 RJ-45 Connector
USB1 Double Stack USB type A Connector
Jumpers
Label Description
AT1 AT/ATX Power Mode Selection
JP1 PATA IDE Enable/ Disable Selection
JBAT1 Clear CMOS Setting
JRS1 COM2 RS-232/422/485 Mode Selecttion

- 5 -
Board Dimensions
121.92
4.98 5.93
11.1
338.58
13.72 22.99 25.15 14.57 10.01
100.34
121.92
240.91
72.01
26.76 71.98
340.58
27.3
187.06
Unit: mm
Heat-sink

- 6 -
Jumpers & Connectors
18 19 20 21 22
KBM1
TPM1
SATA2 SATA1
JFRT1
IR1
EATX1
LAN1
ATX12V1
GF2GF1
DIMM2 DIMM1
VGA1
AT1
JP1
JBAT1
USB1
COM2
JRS1
CN3
SYSF2
SYSF1
DIO1
EKB1
USB3 USB6 USB4 USB5 USB2
CPUF1
1
2
3
4
5
1
1
1
1
2
6
78
9 10
11
17
12
16
COM1
13
FDD1
14
IDE1
15
23
24
27 28 29 30
25
26
1
11
1
1
1
1
1
1
11111
1
1
1
11

- 7 -
Jumpers
JBAT1: Clear CMOS Seting (17)
Connector type: 2.54mm pitch 1x3 pin header.
Pin Mode
1-2 Keep CMOS (Default)
23 1
2-3 Clear CMOS
23 1
Connectors
JRS1: COM2 RS-232/422/485 Mode
Selection (25)
Connector type: 2.54mm pitch 2x7 pin header
Mode RS-232
(Default) RS-422 RS-485
1-2 Off On On
3-4 Off On On
5-6 Off Off On
7-8 Off On Off
9-10 Off On On
11-12 On Off Off
13-14 Off Off On
1 2
13 14
1 2
13 14
1 2
13 14
JP1: PATA IDE Enable/ Disable
Selection (12)
Connector type: 2.54mm pitch 1x2 pin header.
Pin 1-2 Function Select
Short Disable
1 2
Open Enable (Default)
1 2
AT1: AT/ATX Power Mode Selection (11)
Connector type: 2.54mm pitch 1x2 pin header.
Pin 1-2 Power Mode Select
Short AT Mode
1 2
Open ATX Mode
(Default)
1 2
ATX12V1: ATX +12V Connector (1)
ATX12V1 supplies the CPU operation ATX +12V
(Vcore).
Pin Desc. Pin Desc.
2
4
1
3
2GND 1GND
4+12V 3+12V
CPUF1: CPU Fan Power Connector (3)
Connector type: 2.54mm pitch 1x4 wafer one wall
connector.
Pin Description
1
2
3
4
1GND
2+12V
3Fan_ Detect
4Fan Speed Control
JFRT1: Switches and Indicators (2)
It provides connectors for system indicators that
provides light indication of the computer activities
and switches to change the computer status.
Connector type: 2.54mm pitch 2x8 pin header.
1
216
15
Pin Description Pin Description
1Power LED+ 2PWRBTN-
3GND 4PWRBTN+
5GND 6 RESET+
7 HDD LED+ 8 RESET-
9 HDD LED- 10 SPKR
11 SMB_CLK 12 SPEAKER-
13 SMB_DATA 14 GND
15 GND 16 +5V
SYSF1, SYSF2: Fan Power Connector
(4), (5)
SYSF1 and SYSF2 are a 3-pin header for the CPU
fan. The fan must be a +12V fan.
Pin Description
1
2
3
1GND
2+12V
3FAN_CTL

- 8 -
CN3: HD AUDIO daughter board
connector (8)
Connector type: 2.00mm pitch 1x9 box wafer
connector.
Pin Description
1
2
3
4
5
6
7
8
9
1+12V
2+3.3V
3AC_SYNC
4AC_SDOUT
5GND
6AC-BCLK
7 GND
8 AC_RST#
9 AC_SDIN0
COM1: RS-232 Connector (13)
Connector type: 2.54mm pitch 2x5 box header.
Pin Desc. Pin Desc.
1 2
9 10
1DCD1# 2DSR1#
3RXD1 4RTS1#
5TXD1 6 CTS1#
7 DTR1# 8 RI1#
9 GND 10 GND
EATX1: ATX Feature Connector (6)
Connector type: 2.54mm pitch 1x3-pin box wafer
connector
Pin Description
1
2
3
1PS-ON
2GND
35V_SB
FDD1: FDD Connector (14)
Connector type: 2.54mm pitch 2x17 box header.
1
2
33
34
Pin Description Pin Description
1GND 2DRVDEN0
3GND 4N/C
5GND 6 DRVDEN1
7 GND 8 INDEX#
9 GND 10 MOA#
11 GND 12 DSB#
13 GND 14 DSA#
15 GND 16 MOB#
17 GND 18 DIR#
19 GND 20 STEP#
21 GND 22 WDATA#
23 GND 24 WGATE#
25 GND 26 TRACK0#
27 GND 28 WP#
29 GND 30 RDATA#
31 GND 32 HEAD#
33 GND 34 DSKCHG#
TPM1: Trusted Platform Module Connector
(7)
Connector type: 2.54mm pitch 2x10 pin header
Pin Desc. Pin Desc.
1 2
19 20
1 CLK 2 GND
3LFRAME# 4N/C (Key)
5LRESET# 6 N/C
7 LAD3 8 LAD2
9 +3.3V 10 LAD1
11 LAD0 12 GND
13 N/C 14 N/C
15 +3.3V_SB 16 SERIRQ
17 GND 18 CLKRUN#
19 PD# 20 N/C
SATA1~2: SATA Connectors (9)~ (10)
High speed transfer rates (300MB/s).
Pin Description
1GND
2TX+
3TX-
4GND
5RX-
6 RX+
7 GND

- 9 -
IR1: Infrared Connector (23)
Connector type: 2.54mm pitch 1x5 pin header.
Pin Description
1
2
3
4
5
1+5V
2N/C
3IRRX
4GND
5IRTX
IDE1: IDE Connector (15)
Connector type: 2.54mm pitch 2x20 box header.
1
2
39
40
Pin Description Pin Description
1IDE RESET 2GND
3DATA7 4DATA8
5DATA6 6DATA9
7DATA5 8 DATA10
9DATA4 10 DATA11
11 DATA3 12 DATA12
13 DATA2 14 DATA13
15 DATA1 16 DATA14
17 DATA0 18 DATA15
19 GND 20 N/C (Key)
21 REQ 22 GND
23 IO WRITE 24 GND
25 IO READ 26 GND
27 IO READY 28 IDESEL
29 DACK 30 GND
31 IRQ14 32 N/C
33 ADDR1 34 ATA66 DETECT
35 ADDR0 36 ADDR2
37 CS0# 38 CS1# (HD SELECT1#)
39 IDEACTP 40 GND
USB2~6: USB Connector (18)~(22)
Connector type: 2.54mm pitch 2x5 pin header.
Pin Desc. Pin Desc.
1 2
9 10
1+5V 2+5V
3USBD- 4USBD-
5USBD+ 6 USBD+
7 GND 8 GND
9 N/C (Key) 10 N/C
COM2: RS-232/422/485 Connector (26)
Connector type: 2.54mm pitch 2x7 box header.
Pin Desc. Pin Desc.
1 2
13 14
1DCD2# 2DSR2#
3RXD2 4RTS2#
5TXD2 6 CTS2#
7 DTR2# 8 RI2#
9 GND 10 GND
11 TX+ 12 TX-
13 RX+ 14 RX-
Note:
If you congured the port to RS-485 mode, the
signals TX and RX should be already connected.
DIO1: Digital I/O Connector (16)
DIO1 supports 4-bit In/ 4-bit Out.
Connector type: 2.54mm pitch 2x5 box header
Pin Description Pin Description
1 2
9 10
1DO0 2DI0
3DO1 4DI1
5DO2 6 DI2
7 DO3 8 DI3
9 +5V 10 GND
EKB1: External Keyboard Connector
(24)
Connector type: 2.54mm pitch 1x5-pin box wafer
connector.
Pin Description
1KB_CLK
4
2
3
1
5
2KB_DATA
3N/C
4GND
5+5V

- 10 -
LAN1: RJ-45 Connector (29)
Connector type: RJ-45 connector.
LED LED
LAN
8 7 6 5 4 3 2 1
KBM1: Keyboard & Mouse Connector (27)
Mini-Din Keyboard & Mouse connector
Pin Description
12
3
56
4
1KB Data
2MS Data
3GND
4+5V
5KB Clock
6 MS Clock
USB1: Double Stack USB type A
Connector (30)
Connector type: double stack USB type A
connector.
USB
USB
1 2 3 4
1 2 3 4
VGA1: CRT Connector (28)
Connector type: D-Sub 15-pin female.
Pin Desc. Pin Desc.
1
515
11
1RED 9 N/C
2 GREEN 10 GND
3 BLUE 11 N/C
4N/C 12 D-DATA
5GND 13 H-SYNC
6 GND 14 V-SYNC
7 GND 15 D-DCLK
8 GND