Arbor Technology EmCORE-i9651 User manual

- 1 -
Quick Installation Guide
Version 1.3
If you have any technical difculties, please consult the user’s manual rst at:
ftp://ftp.arbor.com.tw/pub/manual
Please do not hesitate to call or e-mail our customer service when you still can not
nd out the answer.
http://www.arbor.com.tw
E-mail: [e-mail]
♦ Technical Support
EmCORE-i9651
3.5" Compact Board
Form Factor
3.5" Compact Board
Video
Dual Channels 24-bit
LVDS/ Analog RGB
I/O
CF II/ Mini PCI/ SATA/
USB 2.0/ IDE/ COM/ LPT/
FDD / DIO
CPU
mPGA 478 Socket for
Intel® Core™ 2 Duo
Processor, up to FSB
800MHz
LAN
2 x Realtek 8111 PCIe
Gigabit Ethernet
Audio
Realtek ALC888 HD
Audio Codec, 7.1 channel,
Line-in/out, Mic-in
Chipset
Intel® GME965
Intel® ICH8M
Copyright® 2011 All Rights Reserved. 4041965100130P
Declaration of Conformity
FCC Class A
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions : (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.

- 2 -
EmCORE-i9651VL2 EmCORE-i9651 3.5" Compact Board w/ dual LAN
Cable Kit
CBK-09-9651-00
1 x COM Port
Cable
1 x IDE Cable
2 x SATA Cable
1 x Audio Cable
1 x KB & MS Cable
2 x USB Cable
1 x Parallel Port Cable
1 x LPT to FDD Cable
1 x LAN Cable
Ordering Information
Packing List
Before you begin installing your single board, please make sure that the
following materials have been shipped:
1 x EmCORE-i9651 3.5” Compact Board
1 x Driver CD
1 x Quick Installation Guide
1 x CPU Cooler
90 x 66 x 27.8mm (L x W x H)
1 x ATX Power cable
ATX main power connector (2x10 pins) to
EmCORE-i9651 power connector (2x5 pins)
If any of the above items is damaged or missing, contact your vendor imme-
diately.

- 3 -
Find Device Drivers on CD
Windows 2000 & XP
Device Driver Path
Chipset \CHIPSET\INF 9.11
LAN \ETHERNET\REALTEK\8111_WINXP_5764
VGA \GRAPHICS\INTEL_2K_XP_32\1437
\GRAPHICS\INTEL_2K_XP_64\1437
Audio \AUDIO\REALTEK_HD\WIN2K_XP_X86X64_R252
Windows 7
Device Driver Path
Chipset \CHIPSET\INF 9.1.1.1004
LAN Windows 7 built-in LAN driver
VGA \GRAPHICS\INTEL_WIN7_32\1930
\GRAPHICS\INTEL_WIN7_64\1930
Audio \AUDIO\REALTEK_HD\WIN7_R252

- 4 -
Form Factor 3.5" Compact Board
CPU
Support 478 Socket for Intel® Core™ 2 Duo
Processor up to 800MHz FSB, Intel® Celeron M
processor with 533/667MHz FSB
Chipset Intel® GME965 + Intel® ICH8M
System Memory 1 x 200-pin SO-DIMM socket Up to 2GB DDR2
533/667MHz SDRAM
VGA/ LCD Control-
ler
Mobile Intel® Graphics Media Accelerator (GMA)
X3100 graphics core w/ Analog RGB/ LVDS 24-bit
dual Channels
Ethernet 2 x Realtek 8111 PCIe Gigabit Ethernet Controllers
I/O Chips Winbond W83627HG
BIOS AMI PnP Flash BIOS
Audio Realtek ALC888 HD Audio Codec, MIC-in/Line-In/
Line-Out
Serial ATA 2 x Serial ATA ports with 300MB/s HDD transfer rate
IDE Interface 1 x IDE (Ultra ATA 33), support 2 IDE devices
Serial Port 2 x COM ports (COM1: RS-232, COM2: RS-
232/422/485)
Parallel Port/ FDD 1 x LPT Port (SPP/EPP/ECP mode selectable)
1 x Floppy connector share with LPT port
IrDA 1 x IrDA connector
KBMS Standard PS/2 Keyboard and Mouse via Y-cable
Universal Serial Bus 6 x USB 2.0 ports
DIO 8-bit programmable Digital Input/Output
Expansion Interface 1 x CF II Socket (Share with IDE)
1 x Mini PCI Socket
Operation Temp. -20oC ~ 70oC (-4oF ~ 158oF)
Watchdog Timer 255-level Reset
Dimension (L x W) 146 x 102 mm ( 5.7" x 4.0" )
Specications

- 5 -
Board Dimensions
Unit:mm
28.24 32.87
115.11 17.15
101.25
46.99
108.14
30.11.6
16.86.5
3.38 95.2
101.96
8.84133.93
146
30.48 45.98
41.27
1.2
67.2
3.35
83.36
97.97
?3.1
?6.35
7.32 90
1
2
1
1
1
NO COMPONENT

- 6 -
Jumpers/ Connectors Quick Reference
Label Function
JP1, JP3 COM Port Power Special
Support
JRS1 COM2 RS-232 / 422 / 485
Selection
JPWR1 AT/ATX Power Mode Selection
JVLCD1 LCD Voltage Selection
JP2 Compact Flash Selection
JBAT1 Clear CMOS Setting
Jumpers
Label Function
IDE1 IDE Connector
LVDS1 LVDS LCD Connector
IR1 Infrared Connector
SATA1,
SATA2 Serial ATA Connectors
CON1 RS-422/485 Output Connector
LLED1 LAN LED Indicator
JSMB1 External SMBus Connector
DIO1 Digital I/O Connector
LPT1 Parallel Port or FDD Connector
COM1 RS-232 Connector
CPUF1 Fan Power Connector
INV1 LCD Inverter Connector
JFRT1 Switches and Indicators
USB1,
USB2 USB Port Connectors
ATX1 ATX Power Supply Connector
LAN1 GbE Connector
MINIPCI1 MiniPCI Socket
AUDIO1 Audio Connector
COM2 RS-232/422/485 Connector
VGA1 Analog RGB Connector
KBM1 Keyboard & Mouse Connector
LAN2 GbE RJ-45 Connector
USB3 USB Double Stacks Connector
CFD1 Compact Flash Socket
Connectors
Label Function
RES1 Reset Switch
Switch

- 7 -
Jumpers & Connectors Location
25
50 26
1
200
199
2
1
40
42
3941
CFD1
200pin DDR II SO-DIMM Socket
12
9
99
10
12
12
44
43
2
1
19
20 2
1
1
1
1
6
5
2
1
2
1
109
2
1123
124
10
9
2
1
29 30
21
10
9
109
21
1
3
1
510
16
1
1
1
LVDS1
IR1 JPWR1
ATX1
COM2 VGA1 RES1 KBM1 LAN2 USB3
AUDIO1
MINIPCI1
USB2
USB1
LAN1
INV1
JRS1
COM1 JFRT1
CON1
LLED1
SATA2
SATA1
LPT1
IDE1
1
JBAT1
1
1
1
1
21
JP3
JP2
JVLCD1
JP1
JSMB1
DIO1
23
1
4 5
11
67
8910
12
13
14
CPUF1
15
17
21
22
18
20
23 24
26
25
27
28 29
30 31 32 33
16
34
19

- 8 -
Jumpers Connectors
JBAT1: Clear CMOS Setting (27)
Connector type: 2.54mm pitch 1x3-pin headers
Pin Mode
1-2 Keep CMOS (Default)
23 1
2-3 Clear CMOS
23 1
JP2: Compact Flash Selection (17)
Connector type: 2.54mm pitch 1x2 pin header.
Pin Mode
Short Master 1 2
Open Slave (Default)
1 2
JVLCD1: LCD Panel Voltage Selection (16)
The voltage of LCD panel could be selected by
JVLCD1 in +5V or +3.3V.
Connector type: 2.54mm pitch 1x3-pin headers
Pin Voltage
1-2 +5V
23 1
2-3 +3.3V (Default)
23 1
JPWR1: AT/ATX Power Mode Selection (14)
Connector type: 2.54mm pitch 1x2-pin headers
Pin Mode
Short AT mode 1 2
Open ATX Mode (Default)
1 2
JRS1: COM2 RS-232/422/485 Selection (12)
Connector type: 2.00mm pitch 2x3-pin headers
Mode RS-232
(Default) RS-422 RS-485
1-2 Short Open Open
3-4 Open Short Open
5-6 Open Open Short
65
2
1
65
2
1
65
2
1
JP1, JP3: COM Port Power Special Support
(8),(21)
Connector type: 2.54mm pitch 1x3-pin headers
Pin Mode
1-2 Standard signal for Pin-9
(Default)
23 1
2-3 +12V
23 1
IDE1: Primary IDE Connector (1)
Connector type: 2.00mm pitch 2x22-pin box headers
1 2
43 44
Pin Description Pin Description
1 IDE RESET 2 GND
3DATA7 4DATA8
5DATA6 6DATA9
7DATA5 8 DATA10
9DATA4 10 DATA11
11 DATA3 12 DATA12
13 DATA2 14 DATA13
15 DATA1 16 DATA14
17 DATA0 18 DATA15
19 GND 20 N/C
21 REQ 22 GND
23 IO WRITE 24 GND
25 IO READ 26 GND
27 IO READY 28 IDSEL
29 DACK 30 GND
31 IRQ14 32 N/C
33 ADAD1 34 ATA66 DETECT
35 ADAD0 36 ADAD2
37 CS#1 38 CS#3
39 IDEACT 40 GND
41 +5V 42 +5V
43 GND 44 N/C
LVDS1: LVDS LCD Connector (2)
Connector type: DF-13-30DP-1.25V connector and
supports 24-bit dual channels
Pin Desc. Pin Desc.
1
2930
2
2 VDD 1 VDD
4TX2CLK+ 3TX1CLK+
6TX2CLK- 5TX1CLK-
8GND 7GND
10 TX2D0+ 9TX1D0+
12 TX2D0- 11 TX1D0-
14 GND 13 GND
16 TX2D1+ 15 TX1D1+
18 TX2D1- 17 TX1D1-
20 GND 19 GND
22 TX2D2+ 21 TX1D2+
24 TX2D2- 23 TX1D2-
26 GND 25 GND
28 TX2D3+ 27 TX1D3+
30 TX2D3- 29 TX1D3-

- 9 -
DIO1: Digital I/O Connector (10)
DIO1 is a 8-bit DIO connector w/ Onboard 10-pin
header connector, supports 4-bit In/ 4-bit Out.
Connector type: 2.00 mm pitch 2x5-pin headers
Pin Description Pin Description
109
1 2
1DIO1 2DIO2
3DIO3 4DIO4
5DIO5 6DIO6
7DIO7 8DIO8
9+5V 10 GND
LLED1: LAN1 LED Indicator (7)
Connector type: 2.54mm pitch 2x2-pin headers
Pin Description Pin Description
21
43
1LED_Y- 2LED_Y+
3LED_G- 4LED_G+
IR1: Infrared Connector (3)
Connector type: 2.54mm pitch 1x5-pin headers
Pin Description
1
2
3
4
5
1+5V
2N/C
3 IRRX
4GND
5 IRTX
SATA1~2: Serial ATA Connectors (4,5)
High speed transfer rates (300MB/s).
Pin Description
1
7
1GND
2TX+
3 TX-
4GND
5 RX-
6RX+
7GND
CON1: RS-422/485 Output Connector (6)
Connector type: 2.00mm pitch 1x4-pin box wafer
connector
Pin RS-422 RS-485
1
2
3
4
1TX+ DATA+
2 TX- DATA-
3RX+ N/C
4 RX- N/C
SMBUS1: External SMBUS Connector (9)
Connector type: 2.54mm pitch 1x3-pin box wafer
connector.
Pin Description 1
2
3
1 Data
2Clock
3GND
LPT1: Parallel Port or FDD Connector (11)
Pin Description Pin Description
1STROBE# 2 AFD#
3 PTD0 4 Error#
5 PTD1 6 INIT#
7 PTD2 8 SLIN#
9 PTD3 10 GND
11 PTD4 12 GND
13 PTD5 14 N/C (Key)
15 PTD6 16 Busy
17 PTD7 18 PE
19 ACK# 20 Select
Connector type: 2.00 mm pitch 2x10-pin headers.
It can be selected by LPT or FDD mode via BIOS.
Parallel port connector is shared with FDD.
Pin Description Pin Description
1N/C 2RWC#
3 RINDEX# 4 HEAD#
5TRACK0# 6 DIR#
7WP# 8 STEP#
9 RDATA# 10 GND
11 DSKCHG# 12 GND
13 N/C 14 N/C (Key)
15 N/C 16 MOB#
17 N/C 18 WD#
19 DSB# 20 WE#
1
2
19
20

- 10 -
ATX1: ATX Power Supply Connector (22)
Pin Description Pin Description
16
510
65VSB 1PS-ON
7+5V 2GND
8+5V 3GND
9 -12V 4 +12V
10 GND 5+3.3V
AUDIO1: Audio Connector (26)
Connector type: 2.00mm pitch 2x5-pin headers
Pin Description Pin Description
109
1 2
1 Line Left In 2 Line Right In
3GND 4GND
5MIC1 6MIC2
7GND 8GND
9 Line-out Left 10 Line-out Right
JFRT1: Switches and Indicators (19)
It provides connectors for system indicators that
provides light indication of the computer activities
and switches to change the computer status.
Connector type: 2.54mm pitch 2x5pin headers
Pin Description Pin Description
109
1 2
1RESET+ 2 RESET-
3POWER_LED+ 4POWER_LED-
5HDD_LED+ 6HDD_LED-
7SPEAKER+ 8SPEAKER-
9PSON+ 10 PSON-
COM1: RS-232 Connector (13)
Connector type: 2.00mm pitch 2x5-pin headers
Pin Desc. Pin Desc.
109
1 2
1 DCD# 2 RXD
3 TXD 4 DTR#
5GND 6 DSR#
7 RTS# 8 CTS#
9 RI# 10 N/C
CPUF1: Fan Power Connector (15)
CPUF1 is a 3-pin headers for the CPU fan. The fan
must be a +12V fan.
Pin Description
1
2
3
1GND
2+12V
3FAN_Detect
INV1: LCD Inverter Connector (18)
Connector type: 2.00mm pitch 1x5-pin box wafer
connector.
Pin Description
1
2
3
4
5
1+12V
2GND
3Backlight on/off
4Brightness control
5GND
USB1~2: USB Connectors (20,23)
Connector type: 2.00mm pitch 2x5-pin headers
Pin Desc. Pin Desc.
12
10
9
1+5V 2+5V
3USBD- 4USBD-
5USBD+ 6USBD+
7GND 8GND
9GND 10 N/C (Key)
LAN1: GbE Connector (24)
Connector type: 2.00mm pitch 2x5-pin headers
Pin Desc. Pin Desc.
109
1 2
1TX_MDI0+ 2TX_MDI0-
3RX_MDI1+ 4MDI2+
5MDI2- 6RX_MDI1-
7MDI3+ 8MDI3-
9N/C 10 N/C (Key)
MINIPCI1 : MiniPCI Socket (25)
COM2: RS-232/422/485 Connector (28)
Connector type: D-Sub 9-pin male connector
Pin Desc. Pin Desc.
1
5
9
6
6 DSR# 1 DCD#
7 RTS# 2 RXD
8 CTS# 3 TXD
9 RI# 4 DTR#
5GND

- 11 -
RES1 : Reset Switch (30)
VGA1: Analog RGB Connector (29)
Connector type: D-Sub 15-pin female connector
Pin Desc. Pin Desc.
1
515
11
1 RED 9 N/C
2GREEN 10 GND
3BLUE 11 N/C
4N/C 12 D-DATA
5GND 13 H-SYNC
6GND 14 V-SYNC
7GND 15 D-DCLK
8GND
LAN2: GbE RJ-45 Connector (32)
LAN2 supports 10/100/1000 Mbps Fast Ethernet
Connector type: RJ-45
USB3: Double Stack USB type A Connector
(33)
Connector type: double stack USB type A connector.
USB
USB
1 2 3 4
1 2 3 4
CFD1 : Compact Flash Disk socket (share with
IDE1) (34)
Pin Description Pin Description
1GND 26 CF_Detect
2 PDD3 27 PDD11
3 PDD4 28 PDD12
4 PDD5 29 PDD13
5 PDD6 30 PDD14
6 PDD7 31 PDD15
7 PDCS1# 32 PDCS3#
8GND 33 N/C
9GND 34 PDIOR#
10 GND 35 PDIOW#
11 GND 36 +5V
12 GND 37 PIDEIRQ
13 +5V 38 +5V
14 GND 39 CSEL#
15 GND 40 N/C
16 GND 41 IDERST#
17 GND 42 PIORDY
18 PDA2 43 PDDREQ
19 PDA1 44 PDDACK#
20 PDA0 45 HD_LED1#
21 PDD0 46 PDIAG#
22 PDD1 47 PDD8
23 PDD2 48 PDD9
24 N/C 49 PDD10
25 N/C 50 GND
KBM1: Keyboard & Mouse (31)
Mini-Din Keyboard & Mouse connector
Connector type: 6-pin mini DIN.
Pin Description
12
3
56
4
1KB Data
2MS Data
3GND
4+5V
5KB Clock
6MS Clock
Note:
1. CF Socket supports up to 4GB.
2. CF Socket does not support Hot Swap.
3. CF and ATA channel are alternative.

- 12 -
This page is intentionally left blank.