Arbor Technology EmCORE-i65M3 User manual

EmCORE-i65M3
User’s Manual
Version 1.0
2012.08
3.5” Compact Board

This page is intentionally left blank.

- I -
Index
Contents
Chapter 1 - Introduction...........................................................1
1.1 Copyright Notice...........................................................2
1.2 Declaration of Conformity ...........................................2
1.3 About This User’s Manual ...........................................4
1.4 Warning .........................................................................4
1.5 Replacing the Lithium Battery.....................................4
1.6 Technical Support ........................................................4
1.7 Warranty ........................................................................5
1.8 Packing List ..................................................................6
1.9 Ordering Information....................................................6
1.10 Specications .............................................................7
1.11 Board Dimensions ......................................................8
Chapter 2 - Installation.............................................................9
2.1 Block Diagram ...........................................................10
2.2 Jumpers.......................................................................11
2.3 Connectors..................................................................12
Jumpers..............................................................................13
JBAT1: Clear CMOS Setting .........................................13
JPWR1: AT/ATX Power Mode Selection ......................15
JRS1: COM2 RS-232/422/485 Mode Selection ............16
JRS1: COM2 RS-485 Auto-FLow Selection .................16
JVLCD1: LVDS1 LCD Panel Voltage Selection ...........18
Connectors.........................................................................19
PWR1: +12V Connector ................................................19
SMBUS1: External SMBUS Connector ........................20
JLPC1: Low Pin Count Connector ...............................21
BAT1: Battery Holder.....................................................22
JFRT1: Switches and Indicators...................................23
AUDIO1: AUDIO Connector ..........................................25
USB1, 2: USB Connectors ............................................26
COM2: Serial Port Connector ......................................27
SATA1,2: Serial ATA Connectors .................................28

- II -
Index
CON1: RS-422/ 485 Connector .....................................29
PWR2: SATA Power Connector ....................................30
CPUF1: CPU Fan Connector ........................................31
COM1: Serial Port Connector ......................................32
LVDS1: LVDS Connector ..............................................33
INV1: LCD Inverter Connector .....................................35
DVI1: DVI Connector .....................................................36
USB3: USB Port Connectors .......................................38
LAN1, 2: Gigabit Ethernet Connectors .......................39
MC1: Mini-card Socket .................................................40
DIMM1: SO-DIMM Socket ..............................................41
CF1: CFast Socket ........................................................42
SIM1: SIM Card Socket .................................................44
2.6 The Installation Paths of CD Driver ..........................45
Chapter 3 - BIOS.....................................................................47
3.1 BIOS Main Setup.........................................................48
3.2 Advanced Settings .....................................................49
3.2.1 ACPI Conguration ..............................................50
3.2.2 CPU Conguration...............................................51
3.2.3 SATA Conguration .............................................52
3.2.4 Intel Anti-Theft Technology Conguration ........53
3.2.5 USB Conguration...............................................54
3.2.6 Super IO Conguration .......................................56
3.2.7 H/W Monitor..........................................................58
3.2.8 Conosole Redirection..........................................59
3.2.9 Sandybridge PPM Conguration........................60
3.3 Chipset ........................................................................61
3.3.1 System Agent (SA) Conguration ......................62
3.3.2 PCH-IO Conguration..........................................72
3.4 Boot Settings ..............................................................77
3.5 Security .......................................................................78
3.6 Save & Exit..................................................................80

- III -
3.7 AMI BIOS Checkpoints...............................................81
3.7.1 Checkpoint Ranges .............................................81
3.7.2 Standard Checkpoints.........................................82
Appendix .................................................................................90
Appendix A: I/O Port Address Map .................................91
Appendix B: Interrupt Request Lines (IRQ) ...................94
Appendix C: BIOS Memory Map......................................95

- IV -
This page is intentionally left blank.

- 1 -
Introduction
1Chapter 1
Introduction
Chapter 1 - Introduction

- 2 -
Introduction
1.1 Copyright Notice
All Rights Reserved.
The information in this document is subject to change without prior notice in
order to improve the reliability, design and function. It does not represent a
commitment on the part of the manufacturer.
Under no circumstances will the manufacturer be liable for any direct, indirect,
special, incidental, or consequential damages arising from the use or inability
to use the product or documentation, even if advised of the possibility of such
damages.
This document contains proprietary information protected by copyright.
All rights are reserved. No part of this manual may be reproduced by any
mechanical, electronic, or other means in any form without prior written
permission of the manufacturer.
1.2 Declaration of Conformity
CE
The CE symbol on your product indicates that it is in compliance with the
directives of the Union European (EU). A Certicate of Compliance is available
by contacting Technical Support.
This product has passed the CE test for environmental specications when
shielded cables are used for external wiring. We recommend the use of
shielded cables. This kind of cable is available from ARBOR. Please contact
your local supplier for ordering information.
This product has passed the CE test for environmental specications. Test
conditions for passing included the equipment being operated within an
industrial enclosure. In order to protect the product from being damaged by
ESD (Electrostatic Discharge) and EMI leakage, we strongly recommend the
use of CE-compliant industrial enclosure products.
Warning
This is a class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
FCC Class A
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:

- 3 -
Introduction
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference
that may cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
RoHS
ARBOR Technology Corp. certies that all components in its products are in
compliance and conform to the European Union’s Restriction of Use of Haz-
ardous Substances in Electrical and Electronic Equipment (RoHS) Directive
2002/95/EC.
The above mentioned directive was published on 2/13/2003. The main pur-
pose of the directive is to prohibit the use of lead, mercury, cadmium, hexava-
lent chromium, polybrominated biphenyls (PBB), and polybrominated diphenyl
ethers (PBDE) in electrical and electronic products. Member states of the EU
are to enforce by 7/1/2006.
ARBOR Technology Corp. hereby states that the listed products do not contain
unintentional additions of lead, mercury, hex chrome, PBB or PBDB that ex-
ceed a maximum concentration value of 0.1% by weight or for cadmium exceed
0.01% by weight, per homogenous material. Homogenous material is dened
as a substance or mixture of substances with uniform composition (such as sol-
ders, resins, plating, etc.). Lead-free solder is used for all terminations (Sn(96-
96.5%), Ag(3.0-3.5%) and Cu(0.5%)).
SVHC / REACH
To minimize the environmental impact and take more responsibility to the
earth we live, Arbor hereby conrms all products comply with the restriction
of SVHC (Substances of Very High Concern) in (EC) 1907/2006 (REACH
--Registration, Evaluation, Authorization, and Restriction of Chemicals)
regulated by the European Union.
All substances listed in SVHC < 0.1 % by weight (1000 ppm)

- 4 -
Introduction
1.3 About This User’s Manual
This user’s manual provides general information and installation instructions
about the product. This User’s Manual is intended for experienced users and
integrators with hardware knowledge of personal computers. If you are not
sure about any description in this booklet. please consult your vendor before
further handling.
1.4 Warning
Single Board Computers and their components contain very delicate
Integrated Circuits (IC). To protect the Single Board Computer and its
components against damage from static electricity, you should always follow
the following precautions when handling it :
1. Disconnect your Single Board Computer from the power source when you
want to work on the inside.
2. Hold the board by the edges and try not to touch the IC chips, leads or cir-
cuitry.
3. Use a grounded wrist strap when handling computer components.
4. Place components on a grounded antistatic pad or on the bag that comes
with the Single Board Computer, whenever components are separated from
the system.
1.5 Replacing the Lithium Battery
Incorrect replacement of the lithium battery may lead to a risk of explosion.
The lithium battery must be replaced with an identical battery or a battery type
recommended by the manufacturer.
Do not throw lithium batteries into the trash-can. It must be disposed of in
accordance with local regulations concerning special waste.
1.6 Technical Support
If you have any technical difculties, please do not hesitate to call or e-mail our
customer service.
http://www.arbor.com.tw
E-mail:[e-mail]

- 5 -
Introduction
1.7 Warranty
This product is warranted to be in good working order for a period of two years
from the date of purchase. Should this product fail to be in good working order
at any time during this period, we will, at our option, replace or repair it at no
additional charge except as set forth in the following terms. This warranty does
not apply to products damaged by misuse, modications, accident or disaster.
Vendor assumes no liability for any damages, lost prots, lost savings or any
other incidental or consequential damage resulting from the use, misuse of,
or inability to use this product. Vendor will not be liable for any claim made by
any other related party.
Vendors disclaim all other warranties, either expressed or implied, including
but not limited to implied warranties of merchantability and tness for a
particular purpose, with respect to the hardware, the accompanying product’s
manual(s) and written materials, and any accompanying hardware. This limited
warranty gives you specic legal rights.
Return authorization must be obtained from the vendor before returned
merchandise will be accepted. Authorization can be obtained by calling or
faxing the vendor and requesting a Return Merchandise Authorization (RMA)
number. Returned goods should always be accompanied by a clear problem
description.

- 6 -
Introduction
1.8 Packing List
1.9 Ordering Information
If any of the above items is damaged or missing, contact your vendor
immediately.
Packing List
Before you begin installing your single board, please make sure that the following
materials have been shipped:
1 x EmCORE-i65M3 3.5" Compact Board with heatsink
1 x Driver CD
1 x Quick Installation Guide
EmCORE-i65M3-827E Intel® CeleronTM 827E 3.5" Compact Board
FCDB-1293 4 x COM ports, 8-bit digital I/O daughterboard
FCDB-349R 16-bit Digital I/O board
CBK-06-65M3-00
Cable kit
2 x SATA cables
2 x USB dual port cables
1 x Audio Cable
1 x COM port cable

- 7 -
Introduction
1.10 Specications
Form Factor 3.5" Compact Board
CPU Soldered onboard Intel® Sandy Bridge Celeron™ 827E
1.4GHz processor
Chipset Intel® PCH HM65
System Memory 1 x 204-pin DDR3 SO-DIMM socket supporting
1066/800MHz SDRAM up to 4GB
Graphics Integrated Intel® HD Graphics 3000 supporting 24-bit dual
channels LVDS and DVI-I
Ethernet 2 x Intel® 82583V PCIe Gigabit Ethernet controllers
I/O Chips Fintek F71869ED
BIOS AMI® UEFI BIOS
Audio Realtek ALC662 5.1 Channel HD Audio CODEC, Mic-in/ Line-in/
Line-out
Storage
2 x Serial ATA ports with 600MB/s HDD transfer rate
1 x CFast socket
Serial Port
2 x COM ports (COM1: RS-232, COM2: RS-232/422/485
selectable, RS-485 auto ow control)
Extra 4 x COM ports via FCDB-1293
Keyboard & Mouse USB interface for Keyboard and Mouse
Universal Serial Bus 6 x USB 2.0 ports
Digital IO 16-bit programmable Digital Input/Output via FCDB-349R
Expansion Bus
1 x Mini-card socket
1 x SIM socket
LPC interface
Operation Temp. -20oC ~ 70oC (-4oF ~ 158oF)
Operating Humidity 0 ~ 90% (non-condensing)
Watchdog Timer 1~255 levels reset
Dimension (L x W) 146 x 102 mm (5.7" x 4.0")

- 8 -
Introduction
1.11 Board Dimensions
Unit: mm

- 9 -
Installation
2Chapter 2
Installation
Chapter 2 - Installation

- 10 -
Installation
2.1 Block Diagram
LPC I/F LPC connector
DDR3-1600/1333/1066MHz
Dual Channels 24-bit LVDS
1 x LVDS Connector
MIC/ Line-out/ Line-out
HD Audio Link Realtek ALC662
HD CODEC MIC-in/ Line-in/ Line-out
GbE LAN
GbE LAN
COM1~COM2
Analog RGB
1 x SATA port
2 x USB 2.0
4 x USB 2.0
2 x SATA ports
Intel 82583V
GbE controller
1 x PCIex1 Intel 82583V
GbE controller
LPC I/F
Intel®
HM65
PCH
DMI2
(x4)
FDI
Soldered
onboard
Intel®
Celeron 827E
Processor
1 x RJ-45 Connector
1 x RJ-45 Connector
COM1: RS-232
COM2: RS-232/422/485
Fintek
F71869ED
SMBus connector
1 x DVI-I
1 x DDR3
SO-DIMM socket
1 x CFast socket
2 x USB ports (Type A)
2 x SATA connectors
1 x USB Port
1 x PCIex1
Mini-Card socket
4 x USB ports (PH)
Power
DC input
+12V only
Display Port C
SMBus
Chrontel
CH7318C
Level shifter to DVI
DVI
1 x PCIex1

- 11 -
Installation
2.2 Jumpers
C3 C7 C6 C2 C5 C1
PC17
PC1
S7
S1
1
119
1
20
1
1
1
2
3
1
1
1
15
9876 5432
2
1
10
9
22
9
10
10
9
2 1
30
4
1
2
2
3
12
2
111
10
9
2 1
1
JBAT1
1
1
JPWR1
2
8 7
2
1
JRS1
3
1
JVLCD1
4
1
2
17
15
18
16
51
52
1
4
203
204
72
74
71
73
1
2

- 12 -
Installation
2.3 Connectors
C3 C7 C6 C2 C5 C1
PC17
PC1
S7
S1
1
1
1
2
3
1
8 7
2
1
15
10
9
22
9
10
10
9
2
30
4
2
3
12
2
10
9
2
19
202
PWR1
5
SMBUS1
6
JLPC1 7
JFRT1
9
AUDIO1
10
11
USB1
12
USB2
13
COM2
14
SATA2
16
CON1
15
SATA1
17
PWR2
18
CPUF1
22
DVI1
BAT1
8
23
USB3
24
LAN2
25
LAN1
26
CF1
27
SIM1
28
MC1
(Bottom Side)
29
DIMM1
(Bottom Side)
1
2
1715
18
16
51
52
14
203 204
72
74
71
73
12
19
COM1
21
INV1
20
LVDS1

- 13 -
Installation
If the board refuses to boot due to inappropriate CMOS settings here is how
to proceed to clear (reset) the CMOS to its default values.
Connector type: 2.00mm pitch 1x3-pin headers
Pin Mode
1-2 Keep CMOS (Default)
23 1
2-3 Clear CMOS
23 1
You may need to clear the CMOS if your system cannot boot up because you
forgot your password, the CPU clock setup is incorrect, or the CMOS settings
need to be reset to default values after the system BIOS has been updated.
Refer to the following solutions to reset your CMOS setting:
Solution A:
1. Power off the system and disconnect the power cable.
2. Place a shunt to short pin 2 and pin 3 of JBAT1 for ve seconds.
3. Place the shunt back to pin 1 and pin 2 of JBAT1.
4. Power on the system.
Solution B:
If the CPU Clock setup is incorrect, you may not be able to boot up. In this
case, follow these instructions:
Turn the system off, then on again. The CPU will automatically boot up using
standard parameters.
As the system boots, enter BIOS and set up the CPU clock.
Note:
If you are unable to enter BIOS setup, turn the system on and off a few times.
Jumpers
JBAT1: Clear CMOS Setting (1)

- 14 -
Installation
1
S1
1
1
3
11
203
204
72
74
71
73
1
2
1
2
17
15
18
16
51
52
1
4
JBAT1