Arbor technology Emcore-v7002 User manual

EmCORE-v7002

VIA Eden 3.5" Embedded Board

User's Manual

Version 1.0

2008.04

Index

- i -

Table of Contents

Chapter 1 Introduction 1

1.1 Copyright Notice 2

1.2 About this User Manual 2

1.3 Warning 2

1.4 Replacing the lithium battery 3

1.5 Technical Support 3

1.6 Warranty 3

1.7 Packing list 4

1.8 Cable Kit 4

1.9 Ordering Information 5

1.10 Specification 5

1.11 Board dimensions 7

Chapter 2 Installation 8

2.1 Board layout 9

2.2 Jumpers and Connectors 10

Chapter 3 BIOS 19

3.1 BIOS Introduction 20

3.2 BIOS Setup 20

3.3 Standard CMOS Features 21

3.4 Advance BIOS Features 23

3.5 Advanced Chipset Features 26

3.6 Integrated Peripherals 30

3.7 Power Management Setup 36

3.8 PNP/PCI Configurations 38

3.9 PC Health Status 40

3.10 Frequency/Voltage Control 41

3.11 Load Optimized Defaults 42

3.12 Set Password 43

3.13 Save & Exit Setup 44

3.14 Exit Without Saving 44

3.15 BIOS memory mapping 45

3.16 Award BIOS Post Codes 45

Chapter 4 Appendix 51

4.1 I/O Map 52

4.2 IRQ Map 53

4.3 Example of Watch Dog codes 53

EmCORE-v7002

VIA Eden 3.5" Embedded Board

User's Manual

Version 1.0

2008.04

Index

- i -

Table of Contents

Chapter 1 Introduction 1

1.1 Copyright Notice 2

1.2 About this User Manual 2

1.3 Warning 2

1.4 Replacing the lithium battery 3

1.5 Technical Support 3

1.6 Warranty 3

1.7 Packing list 4

1.8 Cable Kit 4

1.9 Ordering Information 5

1.10 Specification 5

1.11 Board dimensions 7

Chapter 2 Installation 8

2.1 Board layout 9

2.2 Jumpers and Connectors 10

Chapter 3 BIOS 19

3.1 BIOS Introduction 20

3.2 BIOS Setup 20

3.3 Standard CMOS Features 21

3.4 Advance BIOS Features 23

3.5 Advanced Chipset Features 26

3.6 Integrated Peripherals 30

3.7 Power Management Setup 36

3.8 PNP/PCI Configurations 38

3.9 PC Health Status 40

3.10 Frequency/Voltage Control 41

3.11 Load Optimized Defaults 42

3.12 Set Password 43

3.13 Save & Exit Setup 44

3.14 Exit Without Saving 44

3.15 BIOS memory mapping 45

3.16 Award BIOS Post Codes 45

Chapter 4 Appendix 51

4.1 I/O Map 52

4.2 IRQ Map 53

4.3 Example of Watch Dog codes 53

Introduction

- 1 -

Introduction

- 2 -

Introduction

Chapter 1

1.1 Copyright Notice

The information in this document is subject to change without prior notice in

order to improve the reliability, design and function. It does not represent a

commitment on the part of the manufacturer. Under no circumstances will

the manufacturer be liable for any direct, indirect, special, incidental, or

consequential damages arising from the use or inability to use the product or

documentation, even if advised of the possibility of such damages. This

document contains proprietary information protected by copyright. All rights

are reserved. No part of this manual may be reproduced by any mechanical,

electronic, or other means in any form without prior written permission of the

manufacturer.

1.2 About this User's Manual

This User's Manual is intended for experienced users and integrators with

hardware knowledge of personal computers. If you are not sure about any

description in this User's Manual, please consult your vendor before further

handling.

1.3 Warning

Embedded Miniboard and their components contain very delicate Integrated

Circuits (IC). To protect the Single Board Computer and its components

against damage from static electricity, you should always follow the following

precautions when handling it :

1.Disconnect your Single Board Computer from the power source when you

want to work on the inside.

2. Hold the board by the edges and try not to touch the IC chips, leads or

circuitry.

3. Use a grounded wrist strap when handling computer components.

4. Place components on a grounded antistatic pad or on the bag that came

with the Single Board Computer, whenever components are separated from

the system.