Arconic ERT7 User manual

December 9, 2016
HK1061
Makers of Huck®, Marson®, Recoil®
Brand Fasteners, Tools & Accessories
Instruction Manual
ERT7 ERT8
Ebbert Rivet Tools
Safety Instructions
3-4
General Information
5
Principle of Operation
5
Specifications
6
Preparation for Use
7
Maintenance
7-8
Disassembly Instructions
9
Assembly Instructions
10
Kits and Accessories
10
Troubleshooting
10
Assembly Drawing &
Parts List ERT7
11
Assembly Drawing &
Parts List ERT8
12

2
ERT7 and ERT8 Ebbert Rivet Tools (HK1061)

3
ERT7 and ERT8 Ebbert Rivet Tools (HK1061)
I. GENERAL SAFETY RULES:
1. A half-hour long hands-on training session with qualified
personnel is recommended before using Huck equipment.
2. Huck equipment must be maintained in a safe working
condition at all times. Tools and hoses should be inspected
at the beginning of each shift/day for damage or wear. Any
repair should be done by a qualified repairman trained on
Huck procedures.
3. For multiple hazards, read and understand the safety
instructions before installing, operating, repairing, maintaining,
changing accessories on, or working near the assembly power
tool. Failure to do so can result in serious bodily injury.
4. Only qualified and trained operators should install, adjust or
use the assembly power tool.
5. Do not modify this assembly power tool. This can reduce
effectiveness of safety measures and increase operator risk.
6. Do not discard safety instructions; give them to the operator.
7. Do not use assembly power tool if it has been damaged.
8. Tools shall be inspected periodically to verify all ratings
and markings required, and listed in the manual, are legibly
marked on the tool. The employer/operator shall contact
the manufacturer to obtain replacement marking labels
when necessary. Refer to assembly drawing and parts list for
replacement.
9. Tool is only to be used as stated in this manual. Any other use
is prohibited.
10. Read MSDS Specifications before servicing the tool. MSDS
specifications are available from the product manufacturer
or your Huck representative.
11. Only genuine Huck parts shall be used for replacements or
spares. Use of any other parts can result in tooling damage
or personal injury.
12. Never remove any safety guards or pintail deflectors.
13. Never install a fastener in free air. Personal injury from
fastener ejecting may occur.
14. Where applicable, always clear spent pintail out of nose
assembly before installing the next fastener.
15. Check clearance between trigger and work piece to ensure
there is no pinch point when tool is activated. Remote
triggers are available for hydraulic tooling if pinch point is
unavoidable.
16. Do not abuse tool by dropping or using it as a hammer. Never
use hydraulic or air lines as a handle or to bend or pry the
tool. Reasonable care of installation tools by operators is an
important factor in maintaining tool efficiency, eliminating
downtime, and preventing an accident which may cause
severe personal injury.
17. Never place hands between nose assembly and work piece.
Keep hands clear from front of tool.
18. Tools with ejector rods should never be cycled without nose
assembly installed.
19. When two piece lock bolts are being used always make sure
the collar orientation is correct. See fastener data sheet for
correct positioning.
II. PROJECTILE HAZARDS:
1. Risk of whipping compressed air hose if tool is pneudraulic
or pneumatic.
2. Disconnect the assembly power tool from energy source
when changing inserted tools or accessories.
3. Be aware that failure of the workpiece, accessories, or the
inserted tool itself can generate high velocity projectiles.
4. Always wear impact resistant eye protection during tool
operation. The grade of protection required should be
assessed for each use.
5. The risk of others should also be assessed at this time.
6. Ensure that the workpiece is securely fixed.
7. Check that the means of protection from ejection of fastener
or pintail is in place and operative.
8. There is possibility of forcible ejection of pintails or spent
mandrels from front of tool.
III. OPERATING HAZARDS:
1. Use of tool can expose the operator’s hands to hazards
including: crushing, impacts, cuts, abrasions and heat. Wear
suitable gloves to protect hands.
2. Operators and maintenance personnel shall be physically able
to handle the bulk, weight and power of the tool.
3. Hold the tool correctly and be ready to counteract normal or
sudden movements with both hands available.
4. Maintain a balanced body position and secure footing.
5. Release trigger or stop start device in case of interruption of
energy supply.
6. Use only fluids and lubricants recommended by the
manufacturer.
7. Avoid unsuitable postures, as it is likely for these not to allow
counteracting of normal or unexpected tool movement.
8. If the assembly power tool is fixed to a suspension device,
make sure that fixation is secure.
9. Beware of the risk of crushing or pinching if nose equipment
is not fitted.
Continued on next page...
GLOSSARY OF TERMS AND SYMBOLS:
- Product complies with requirements set forth by
the relevant European directives.
- Read manual prior to using this equipment.
- Eye protection is required while using this
equipment.
- Hearing protection is required while using this
equipment.
Notes: are reminders of required procedures.
Bold, Italic type, and underline: emphasize a specific
instruction.
WARNINGS: Must be understood to avoid
severe personal injury.
CAUTIONS: Show conditions that will damage
equipment or structure.
Safety Instructions

4
ERT7 and ERT8 Ebbert Rivet Tools (HK1061)
IV. REPETITIVE MOTION HAZARDS:
1. When using assembly power tool, the operator can
experience discomfort in the hands, arms, shoulders, neck
or other parts of the body.
2. When using tool, the operator should adopt a comfortable
posture while maintaining a secure footing and avoid
awkward or off balanced postures.
3. The operator should change posture during extended tasks
to help avoid discomfort and fatigue.
4. If the operator experiences symptoms such as persistent
or recurring discomfort, pain, throbbing, aching, tingling,
numbness, burning sensations or stiffness, these warnings
should not be ignored. The operator should tell the
employer and consult a qualied health professional.
V. ACCESSORIES HAZARDS:
1. Disconnect tool from energy supply before changing
inserted tool or accessory.
2. Use only sizes and types of accessories and consumables
that are recommended. Do not use other types or sizes of
accessories or consumables.
VI. WORKPLACE HAZARDS:
1. Be aware of slippery surfaces caused by use of the tool
and of trip hazards caused by the air line or hydraulic hose.
2. Proceed with caution while in unfamiliar surroundings;
there could be hidden hazards such as electricity or other
utility lines.
3. The assembly power tool is not intended for use in
potentially explosive environments.
4. Tool is not insulated against contact with electrical power.
5. Ensure there are no electrical cables, gas pipes, etc., which
can cause a hazard if damaged by use of the tool.
VII. NOISE HAZARDS:
1. Exposure to high noise levels can cause permanent,
disabling hearing loss and other problems such as tinnitus,
therefore risk assessment and the implementation of
proper controls is essential.
2. Appropriate controls to reduce the risk may include
actions such as damping materials to prevent workpiece
from ‘ringing’.
3. Use hearing protection in accordance with employer’s
instructions and as required by occupational health and
safety regulations.
4. Operate and maintain tool as recommended in the
instruction handbook to prevent an unnecessary increase
in the noise level.
5. Select, maintain and replace the consumable / inserted
tool as recommended to prevent an unnecessary increase
in noise.
6. If the power tool has a silencer, always ensure that it is in
place and in good working order when the tool is being
operated.
VIII. VIBRATION HAZARDS:
1. Exposure to vibration can cause disabling damage to the
nerves and blood supply to the hands and arms.
2. Wear warm clothing when working in cold conditions and
keep hands warm and dry.
3. If numbness, tingling, pain or whitening of the skin in the
ngers or hands, stop using the tool, tell your employer
and consult a physician.
4. Support the weight of the tool in a stand, tensioner, or
balancer in order to have a lighter grip on the tool.
IX. HYDRAULIC TOOL SAFETY INSTRUCTIONS:
1. Carry out a daily check for damaged or worn hoses or
hydraulic connections and replace if necessary.
2. Wipe clean all couplers before connecting. Failure to do
so can result in damage to the quick couplers and cause
overheating.
3. Ensure that couplings are clean and correctly engaged
before operation.
4. Use only clean oil and lling equipment.
5. Power units require a free ow of air for cooling purposes
and should therefore be positioned in a well ventilated area
free from hazardous fumes.
6. Do not inspect or clean the tool while the hydraulic power
source is connected. Accidental engagement of the tool
can cause serious injury.
WARNING: Do not exceed maximum pull or
return settings on tool.
WARNING: Be sure all hose connections are
tight. All tool hoses must be connected.
Safety Instructions (continued)

5
ERT7 and ERT8 Ebbert Rivet Tools (HK1061)











PULL CYCLE
When the trigger is pressed, the incoming non-oiled
plant air, regulated at 90 psi forces the Piston Assembly
and Double Piston to the rear of the tool, and air is
exhausted out the bottom of the tool. The fastener is
installed, and the fastener pintail breaks off.
NOTE: The ERT8 exhaust air exits through small holes
in the bottom of the Valve Body. (See Item 16 of ERT8
Assembly Drawing in this manual.)
RETURN CYCLE
When the trigger is released, the pressurized air is
directed to the rear of the pistons, causing them to move
forward. The fastener pintail is vacuumed out the rear
of the tool and into the Power Unit Pintail Collection bin,
and the tool is ready for the next fastener installation.











This manual contains operating and service procedures
for the Ebbert Rivet Tool models ERT7 and ERT8. Pay
close attention to the recommended service procedures
in this manual.
Specic instructions for each tool are given under that
tool model number heading. While the tools appear
similar, each tool contains parts not used on other
models, and removal and replacement methods may
vary.
General Information
Principle of Operation

6
ERT7 and ERT8 Ebbert Rivet Tools (HK1061)
Specifications


 
 





 







Inches
mm
ERT7




 
 






 


Inches
mm
ERT8
WEIGHT: 3.25 lbs. (1.47 kg)
RIVET SIZES: 1/8”, 5mm, 6mm
WEIGHT: 3.0 lbs. (1.36 kg)
RIVET SIZES: 1/8”, 5mm, 6mm

7
ERT7 and ERT8 Ebbert Rivet Tools (HK1061)
Preparation for Use
1. Use Ebbert Power Unit Model EPS6V or EPS6VL, that has
been prepared for operation per applicable instruction
manual. Check incoming pressures and, if necessary,
adjust to the recommended pressures in S
of this manual.
2. Turn OFF the Ebbert Power Unit, and then disconnect the
power supply from the unit. Connect the tool’s hoses to
the unit.
3. Connect the cable attachment from hose assembly to
cylinder base of tool.
4. Connect the Ebbert Power Unit to the power supply.
Turn ON the unit. Press and hold the tool trigger for 30
seconds; then press the trigger a few times to cycle the
tool. Observe the action of the tool and check for air
leaks. Turn OFF the unit.
5. Select the pulling head assembly for the fastener to
be installed and attach the pintail tube from the hose
assembly to the pulling head. Attach the pulling head
assembly to the tool.
6. Reconnect the Ebbert Power Unit to the power supply.
Check the operation of the pulling head assembly; install
fasteners in test plate of correct thickness with proper
size holes. Inspect the installed fasteners.
Maintenance
GOOD SERVICE PRACTICES
Carefully handle all parts, and examine for damage and
wear. Replace parts where required. Always replace
O-rings and Back-up rings when tool is disassembled
for any reason. See applicable Service Kit.
• The efciency and life of the tool depends on proper
maintenance. Use this manual to better understand
tool and its basic maintenance procedures. Read
this page completely before proceeding with
maintenance and repair. Use proper hand tools
in a clean and well-lighted area; only standard
hand tools are required in most cases. Where a
special tool is required, the part number is given.
• While clamping tool or parts in a vise, and when parts
require force, use suitable soft materials to cushion
impact. For example, use a half-inch brass drift, wood
block, and vise with soft jaws to reduce the possibility
of damaging the tool. Remove components in a
straight line without bending, cocking, or applying
undue force. Reassemble tool with the same care.
• Consult TroubleshooTing section of this manual
if a malfunction occurs and then see appropriate
Disassembly, assembly, and/or assembly Drawings.
Sealants, Lubricants, & Service Kits
• Smear LUBRIPLATE 130-AA, or equivalent, on
O-rings and mating surfaces to prevent damage
to O-rings on rough or sharp surfaces, and to
ease assembly. (LUBRIPLATE in a tube, 502723.)
• Each Service Kit contains perishable parts for your
specic tool. As foreseeable use may indicate, keep
extra kits (O-rings, Back-up rings, other standard
items) and tool parts in stock. When stock is depleted,
you can get kit items from any regular retailer of
these items. See ParTs lisT for: O-ring size (AS568-
number); material; durometer. For kit parts lists
and related information, see KiTs & accessories.
PREVENTIVE MAINTENANCE
System Inspection
The operating efciency of the tool is directly related to
the performance of the complete system, including the
tool with pulling head assembly, trigger, control cord,
and Power Unit. Therefore, an effective preventive
maintenance program includes scheduled inspections
of the system to detect and correct minor troubles.
• Inspect tool and pulling head assembly for external
damage.
• Verify that hose ttings and/or couplings, and/or
electrical connections are secure.
• Observe tool, hoses, and power unit during
operation to detect abnormal heating, leaks, or
vibration.
CAUTION: Keep dirt and other harmful
material out of air ow system, which
includes tool, hoses, couplers and Power
Unit. Parts must be kept away from unclean
work surfaces.
WARNING: Inspect tool for damage or wear
before each use. Do not operate if damaged
or worn, as severe personal injury may
occur.

8
ERT7 and ERT8 Ebbert Rivet Tools (HK1061)
FIgure 1
PREVENTIVE MAINTENANCE (continued)
Power Unit Maintenance
Refer to the applicable Power Unit instruction manual.
Tool Maintenance
Whenever disassembled, and at regular intervals
(depending on severity and length of use), replace all
seals, wipers, and Back-up rings in tool. Service Kits,
hoses, and extra parts should be kept in stock. Inspect
cylinder bore, pistons, and piston rods for scored
surfaces and excessive wear or damage. Replace as
necessary.
Pulling Head Maintenance
Clean the pulling head assembly often. Dip it in mineral
spirits (Figure 1), or similar solvent, to clean jaws and
wash away metal chips and debris. At regular intervals,
as experience shows, disassemble the pulling head
assembly and use a sharp “pick” to remove imbedded
particles from the grooves of the jaws.
Maintenance (continued)

9
ERT7 and ERT8 Ebbert Rivet Tools (HK1061)
Disassembly
This manual provides operating and service procedures
for the Rivet Tool models ERT7 and ERT8. Close
attention must be directed to the recommended
service procedures contained in this manual. Specic
instructions for each tool are given under that tool
model number heading. While the tools look similar,
each tool contains parts not used on the other models
and removal and replacement methods will vary. For
component identication, see Figures 2 and 3 and ParTs
lisT.
NOTE: The following procedure is for complete
disassembly of the tools. Disassemble only those
components necessary to replace damaged O-rings,
seals, Back-up rings, and worn and damaged
components. Disconnect the tool from the Power Source
prior to disassembly.
Removing the Hose Assembly
1. Model ERT7: Remove the guard. (Figure 2)
2. Models ERT7 & ERT8: Remove the pintail tube
from the pulling head assembly. Remove the cable
attachment from the cylinder base. Pull the heavy
plastic sleeve off the air-line connector. Press the
red collet on the air-line connector and pull the air-
line out of the connector. (Figures 2 & 3)
Rivet Tool Disassembly (Figures 2 & 3)
1. Remove the Pulling Head Assembly from the tool;
remove all nicks and burrs from front of Piston Rod
Assembly.
2. Model ERT7: Remove the four screws and the
piston rod guide from the front of the tool. (Figure 2)
Model ERT8: Remove the four screws and handle
from the front of the tool. (Figure 3)
3. Push Piston Assembly to full-back position, and
remove the retaining ring from the rear of the Piston
Assembly.
NOTE: Remove all nicks and burrs from the rear
of the piston to ensure removal of the end cap and
Double Piston without damaging them.
4. Remove the four screws, Support Loop Assembly,
and end cap from rear of tool.
5. Remove the retaining ring from the rear of the
Double Piston. Pull the Piston Assembly out through
the front end of the tool.
6. Push out the Double Piston and Bulkhead through
the rear of tool.
NOTE: It is not necessary to remove the retaining
ring from the cylinder.
CAUTION: Before performing any
maintenance, disconnect the tool’s hoses
from the Power Unit.
Use Area Below for Service Notes

10
ERT7 and ERT8 Ebbert Rivet Tools (HK1061)
Assembly
This procedure is for the re-assembly of the ERT7 and ERT8
tools. For component identification, see Figures 2 and 3 and
P L.
NOTE: Clean components with mineral spirits, or similar
solvent. Inspect for wear/damage and replace as necessary.
Replace all seals of disassembled components. Use O-rings,
Quad-rings and Back-up rings in Service Parts Kit ERT5S7KIT or
ERT8KIT. Coat O-rings, seals, Back-up rings, and mating parts
with conventional O-ring lubricant to ease assembly. Assemble
tool taking care not to damage O-rings, seals, or Back-up rings.
NOTE: Install retaining rings with sharp edge of the retaining
ring toward the rear of the tool.
NOTE: When replacing seals, make sure they are correctly
positioned as shown in the Assembly Drawing.
1. Wipe all seals with a thin film of lubricant before
reassembly.
2. Inspect the cylinder wall to ensure the surface is free of
gouges and nicks that will damage a new seal. Small nicks
and gouges can normally be removed using a fine crocus
cloth.
3. Install the bulkhead into the rear of the cylinder until it
seats flat against the retaining ring in the center of the
cylinder.
4. Upon ensuring that there are no nicks or burrs on the
front or rear of the Piston Assembly, insert the assembly
into the front of the tool, and push it to the full back
position.
5. Install the Double Piston onto the rear of the Piston Rod
Assembly and into the cylinder until it bottoms on the
shoulder of the Piston Assembly.
NOTE: Before placing the cylinder assembly on top of the
handle assembly, ensure the O-rings are in place at the top
of the handle assembly.
6. Install the retaining ring at the back of the Double Piston
with the sharp edge of the snap ring toward the rear of the
tool.
7. Install the rubber bumper on the front end of the Piston
Rod Assembly.
8. Model ERT7: Install the Piston Rod Guide and two bearing
plates, and secure with four screws. Torque the screws to
60–80 inch pounds. (Figure 2)
Model ERT8: Install the handle and two bearing plates, and
secure with four screws. Torque the screws to 60–80 inch
pounds. (Figure 3)
9. Install the end cap and support loop assembly on the rear
of tool and secure with the four screws. Torque the screws
to 60–80 inch pounds.
NOTE: When the tool is used without the support loop
assembly, two additional screw bearing plates are required
between the end cap and the screws.
10. Install the snap ring on the back of the piston assembly
with sharp edge of snap ring toward the rear of the tool.
The Pulling Head Assembly and Hose Assembly can now be
installed.
Always check the simplest possible cause (such as a disconnected air hose) of a malfunction first. Then proceed logically,
eliminating other possible causes until the cause is discovered. Where possible, substitute known good parts for suspected
defective parts. Use this troubleshooting information to aid in locating and correcting trouble.
1. Tool fails to operate when trigger is pressed.
a. Inoperative Power Source. See applicable instruction
manual.
b. Damaged trigger assembly.
c .
2. Tool leaks hydraulic fluid.
a. Defective tool O-rings or loose connections at tool.
3. Hydraulic couplers leak fluid.
a. Damaged or worn O-rings in Coupler Body Coupler.
4. Hydraulic fluid overheats.
a. Unit not operating properly. See unit’s manual.
5. Tool operates erratically and fails to install fastener
properly.
a. Low or erratic hydraulic pressure. Air in system.
b. Worn or damaged piston O-ring in tool.
c. Excessive wear on sliding surfaces of tool parts.
6. Pintail of fastener fails to break.
a. Improper tool operation. See No. 5.
b. Incorrect fastener size or type.
c. PULL pressure too low.
7. Pulling Head will not release broken pintail.
a. Pulling Head assembly not correctly installed.
b. Tool or Pulling Head may need cleaning.
8. Excessive air leaking from trigger and tool will not
function.
a. Green and red air hoses may be switched.
S K
ERT7 and ERT8 - 300471
This kit is for both tools and should be kept on hand at all times. It contains:
P/N P Q. P/N P Q.
500779 O-ring 1 507665 Seal 2
500780 O-ring 1 300066 Seal 2
500794 O-ring 3 300071 Seal 1
300156 Back-up Ring 1 300125 Bumper 1
Kits and Accessories
Troubleshooting

11
ERT7 and ERT8 Ebbert Rivet Tools (HK1061)
Components Drawing & Parts List ERT7


   







 


 













 

 
    

 
 
FIgure 2
iTem ParT no. DescriPTion QTy. iTem ParT no. DescriPTion QTy. iTem ParT no. DescriPTion QTy.
1 300028 Piston Rod Guide 1 2 300004 Cylinder 1 3 300125 Bumper 1 4 507665 Seal 3 5 300145 Piston Assembly 1 6 500950 Retaining Ring 1 7 300065 Bulkhead 1 8 500794 O-ring 3 9 300066 Seal 2 10 500780 O-ring 1 11 300063 Double Piston 1
12 500995 Retaining Ring 2 13 300071 Seal 1 14 300029 End Cap 1 15 506268 Male Connector 1 16 300107 Guard 1 17 300156 Valve Back-up Ring 1 18 500779 O-ring 1 19 300042 Handle 1 20 300251 Trigger 1 21 500623 Pin 1 22 507660 Bleed Screw 2
23 300064 Screw Bearing Plate 2 24 500064 Socket Head Screw 8 25 300114 Support Loop Assembly 1 26 500061 Socket Head Screw 4 27 500055 Socket Head Screw 4 28 501344 Dowel 1 29 300159 Valve 1 30 300124 Spring Seat 1 31 507550 Spring 1 32 300131 Spring Plunger 1

12
ERT7 and ERT8 Ebbert Rivet Tools (HK1061)
Assembly Drawing & Parts List ERT8


   















 



















 

 

 
 
    
FIgure 3
1 300058 Seal Housing 1 2 300005 Cylinder 1 3 300125 Bumper 1 4 507665 Seal 3 5 300144 Piston Assembly 1 6 500950 Retaining Ring 1 7 300065 Bulkhead 1 8 500794 O-ring 3 9 300066 Seal 2 10 500780 O-ring 1 11 300063 Double Piston 1
12 500995 Retaining Ring 2 13 300071 Seal 1 14 300029 End Cap 1 15 506268 Male Connector 1 16 300037 Valve Body 1 17 300156 Valve Back-up Ring 1 18 500779 O-ring 1 19 300105 Handle 1 20 300252 Trigger 1 21 500623 Pin 1 22 507660 Bleed Screw 2
23 300064 Screw Bearing Plate 2 24 500064 Socket Head Screw 8 25 300126 Support Loop Assembly 1 26 500061 Socket Head Screw 4 27 508010 Piston Rod Wiper 1 28 501344 Dowel 1 29 300158 Valve 1 30 300124 Spring Seat 1 31 507550 Spring 1 32 300131 Spring Plunger 1
iTem ParT no. DescriPTion QTy. iTem ParT no. DescriPTion QTy. iTem ParT no. DescriPTion QTy.

13
ERT7 and ERT8 Ebbert Rivet Tools (HK1061)
Limited Warranties
Limited Lifetime Warranty on BobTail® Tools:
Huck International, Inc. warrants to the original purchaser that
its BobTail® installation tools manufactured after 12/1/2016
shall be free from defects in materials and workmanship for its
useful lifetime. This warranty does not cover special order
/ non-standard products, or part failure due to normal wear,
tool abuse or misapplication, or user non-compliance with the
service requirements and conditions detailed in the product
literature.
Two Year Limited Warranty on Installation Tools:
Huck International, Inc. warrants that its installation tools
manufactured after 12/1/2016 shall be free from defects in
materials and workmanship for a period of two years from
date of purchase by the end user. This warranty does not
cover special order / non-standard products, or part failure
due to normal wear, tool abuse or misapplication, or user
non-compliance with the service requirements and conditions
detailed in the product literature.
90 Day Limited Warranty on Nose Assemblies and
Accessories:
Huck International, Inc. warrants that its nose assemblies
and accessories shall be free from defects in materials and
workmanship for a period of 90 days from date of purchase by
the end user. This warranty does not cover special clearance
noses, or special order / non-standard product, or part failure
due to normal wear, abuse or misapplication, or user non-
compliance with the service requirements and conditions
detailed in the product literature.
Useful lifetime is defined as the period over which the
product is expected to last physically, up to the point when
replacement is required due to either normal in-service wear,
or as part of a complete overhaul. Determination is made on a
case-by case basis upon return of parts to Huck International,
Inc. for evaluation.
Tooling, Part(s) and Other Items not manufactured by
Huck:
HUCK makes no warranty with respect to the tooling, part(s),
or other items manufactured by third parties. HUCK expressly
disclaims any warranty expressed or implied, as to the
condition, design, operation, merchantability, or fitness for use
of any tool, part(s), or other items thereof not manufactured
by HUCK. HUCK shall not be liable for any loss or damage,
directly or indirectly, arising from the use of such tooling,
part(s), or other items or breach of warranty or for any claim
for incidental or consequential damages.
Huck shall not be liable for any loss or damage resulting from
delays or non-fulfillment of orders owing to strikes, fires,
accidents, transportation companies or for any reason or
reasons beyond the control of the Huck or its suppliers.
Huck Installation Equipment:
Huck International, Inc. reserves the right to make changes in
specifications and design and to discontinue models without
notice.
Huck Installation Equipment should be serviced by trained
service technicians only.
Always give the serial number of the equipment when
corresponding or ordering service parts.
Complete repair facilities are maintained by Huck International,
Inc. Please contact one of the offices listed below.
Eastern
One Corporate Drive Kingston, New York 12401-0250
Telephone [phone] FAX [phone]
Outside USA and Canada
Contact your nearest Huck International location (see
reverse).
In addition to the above repair facilities, there are Authorized
Tool Service Centers (ATSC’s) located throughout the United
States. These service centers offer repair services, spare parts,
Service Parts Kits, Service Tool Kits and Nose Assemblies.
Please contact your Huck Representative or the nearest Huck
International location (see reverse) for the ATSC in your area.

Arconic Inc. (NYSE: ARNC) creates breakthrough
products that shape industries. Working in close
partnership with our customers, we solve complex
engineering challenges to transform the way we fly,
drive, build and power.
Through the ingenuity of our people and cutting-
edge advanced manufacturing, we deliver these
products at a quality and efficiency that ensures
customer success and shareholder value.
Arconic Fastening Systems and Rings world-wide locations:
AMERICAS
Kingston Operations
1 Corporate Drive
Kingston, NY 12401
800-278-4825
845-331-7300
FAX: [phone]
Carson Operations
900 Watson Center Rd.
Carson, CA 90745
800-421-1459
310-830-8200
FAX: [phone]
Waco Operations
PO Box 8117
8001 Imperial Drive
Waco, TX 76714-8117
800-388-4825
254-776-2000
FAX: [phone]
Tucson Operations
3724 East Columbia
Tucson, AZ 85714
800-234-4825
520-747-9898
FAX: [phone]
Acuña Operations
Hidalgo #120
Parque Industrial Amistad
26220 Acuña Coahuila
Mexico
FAX: [phone]
TELEX: 1173530 LUKSME
EUROPE
Telford Operations
Unit C, Stafford Park 7
Telford, Shropshire
England TF3 3BQ
01952-290011
FAX: [phone]
Us Operations
BP4
Clos D’Asseville
95450 Us par Vigny
France
33-1-30-27-9500
FAX: [phone]
FAR EAST
Melbourne Operations
11508 Centre Road
Clayton, Victoria
Australia 3168
03-764-5500
Toll Free: 008-335-030
FAX: [phone]








Huck is Forever, For the Long Haul, The
Future of Fastening Technology, The Future of
Assembly Technology, The Future of Tooling
Technology, and Tools of Productivity are
service marks of Huck International. Huck
provides technical assistance regarding the use
and application of Huck fasteners and tooling.
NOTICE: The information contained in this
publication is only for general guidance
with regard to properties of the products
shown and/or the means for selecting such
products, and is not intended to create any
warranty, express, implied, or statutory;
all warranties are contained only in Huck’s
written quotations, acknowledgments, and/
or purchase orders. It is recommended that
the user secure specific, up-to-date data and
information regarding each application and/or
use of such products.
© 2016 Huck International, Inc.
1 Corporate Drive, Kingston, NY 12401 • Tel: [phone] • Fax: [phone]