AREBOS AR-HE-RK710USB User manual

User’s Manual –AREBOS Pipe Inspection Camera System
1
Pipe Inspection Camera System
AR-HE-RK710USB
Please follow all security measures in this user´s manual to ensure a secure use.
Thank you for trusting in AREBOS.

User’s Manual –AREBOS Pipe Inspection Camera System
2
List of contents
1. Safety instructions ..........................................................3
1.1 Explanation of the symbols ....................................................................... 3
1.2 General safety instructions........................................................................ 3
1.3 Taking care of your inspection system....................................................... 4
1.4 Operating environment............................................................................. 4
2. Parts List .........................................................................5
2.1 Accessories................................................................................................ 5
2.2 Control box................................................................................................ 6
3. Quick start guide.............................................................8
3.1 Charging the battery ................................................................................. 8
3.2 Starting up................................................................................................. 8
3.3 Checking waterproof ring & Assembling SKID ........................................... 9
3.3.1 Check waterproof rubber ring on the bottom of the camera head ..... 9
3.3.2 40 mm SKID and 23 mm camera head................................................. 9
3.3.2 80 mm SKID and 23 mm camera head................................................. 9
4. Recording and Menu.....................................................10
4.1 Inserting the SD card ............................................................................... 10
4.2 AV1 & AV2 switch.................................................................................... 10
4.3 Recording the video ................................................................................ 11
4.4 Recording the photo................................................................................ 11
4.5 Playback video......................................................................................... 11
4.6 Playback photo........................................................................................ 12
4.7 Menu....................................................................................................... 13
4.8 Recorder Setting...................................................................................... 13
4.9 System Setting......................................................................................... 15
4.10 Delete Files............................................................................................ 16
4.11 Zoom in & Zoom out the image............................................................. 16
5. Troubleshooting Guide..................................................17
6. Disposal instruction ......................................................18
6.1 Disposal of the packaging........................................................................ 18
6.2 Disposal of waste equipment .................................................................. 18
6.3 Meaning of the "dustbin"........................................................................ 18

User’s Manual –AREBOS Pipe Inspection Camera System
3
Please read and save these instructions. Read through this user’s manual carefully before using this
product. Protect yourself and others by observing all safety information, warnings and cautions.
Failure to comply with instructions could result in personal injury and/or damage to product or
property. Please retain instructions for future reference.
1.Safety instructions
1.1 Explanation of the symbols
1.2 General safety instructions
•Read this manual carefully before operating this system.
•Avoid using the device in extreme humidity or temperatures as this may cause damage to the
device.
•Do not drop or press on the system as this may cause damage to the device.
•Do not disconnect the SD card while recording or playing as this may damage the system
and/or the SD card.
•Remember to always back up the data on your SD card.
•Do not attempt to insert, use or charge a battery not designed for this inspection system.
•Use the power supply only on even surfaces, without any cover. Open air and circulation
around the product must be available. The maximum ambient temperature is 50°C.
•Risk of explosion may occur if an incorrect battery type is inserted or used. Dispose of used
batteries according to their instructions.
•Keep the inspection system and its accessories out of the reach of babies, toddlers, and
By means of a CE marking, it can be recognized that a product complies with the
legal requirements of European legal standards and therefore may be traded
within the European Community.
This product must not be disposed of with household waste!
Warning! To avoid electrical shock, put the item indoor when charging.
Warning! Use Input 110 240 V AC Output DC 12.6 V, 1000 mA
Charger ONLY.
Charge the battery first before use!
Warning! Do not use the USB- and SD-connection at the same time!

User’s Manual –AREBOS Pipe Inspection Camera System
4
children. In particular, small parts such as memory cards and battery could be easily
dismantled and swallowed.
•Use only the original accessories to avoid possible risks to health and property, and thus
meet all related legal regulations.
•When using the LED lights, do not use to close to human or animal eyes (particularly for
babies, toddlers and children) to avoid injury.
•In very rare occasions, Li-ion Batteries such as the one provided with this inspection system
could explode if a conductive material such as jewelry, keys or beaded chains touch exposed
terminals. The material may complete an electrical circuit and become quite hot. Exercise
care in handling any batteries, particularly when placing it inside your pocket, purse, or other
container with metal objects. In such an event, this could result in property damage, injury or
burns. Do not dispose of batteries in fire as they may explode.
•Warranty is void if damage or system failure occurred due to outside factors such as collision,
fire, flood, dirt, sewage, earthquake, and other force majeure events as well as incorrect
usage of electricity or use of non-original accessories.
•It is the sole responsibility of the user if problems (such as data loss and system failure)
occurred due to non-factory installed software, parts, and/or non-original accessories.
1.3 Taking care of your inspection system
•Always keep the inspection system in the pouch provided or other suitable cases for
increased protection against splashes, dust, and collision.
•The only way of replacing the battery and the memory card is to open the Battery / Memory
cover. Use care when opening this cover to avoid damage the inspection system.
•Dispose of unwanted batteries and inspection systems as permitted by the laws in your
country.
•Water may cause a fire or electric shock. Therefore, store your battery in a dry place.
•If your control component becomes wet, wipe it with a dry cloth as soon as possible.
•Do not drop, knock, or shake the inspection system. Inappropriate behavior when using the
camera system may damage the internal electronic circuit board or deform the lens shape.
•Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the inspection
system.
•To avoid unclear images, be sure to clean the inspection system lens before taking pictures or
recording videos. Use a lens brush or soft cloth to clean the lens.
•To avoid the loss of video and photos on the memory card, you should make a backup copy
to a computer or optical disc as soon as possible. Memory cards should not be considered as
a long term storage device.
•Before initial use of a memory card, it is recommended to use the inspection system to
format the card first.
•Remember to slide the write-protect tab (if available) to the unlock position. Otherwise, all
data (if any) on the memory card is protected and the card cannot be edited or formatted.
1.4 Operating environment
•The camera system operating temperature is between -10°C - 50°C. It is normal for the
operating time to be shortened when the temperature is low.
•The capacity of your inspection system battery will reduce each time it is charged/emptied.
•Storage at too high or low temperatures will also result in a gradual capacity loss. As a result,
the operating time of your inspection system may be considerably reduced.
•It is normal for the camera system to become warm during operation, because the inspection
system casing can conduct heat.

User’s Manual –AREBOS Pipe Inspection Camera System
5
2.Parts List
2.1 Accessories
Item
Image
Description
Camera Head & Skids
Camera size: ø 0.906 x 4.724 in (23 x 120 mm)
Sensor size: 1/4 in (6,35 mm)
View angle: 120°
Camera work current: 100 mA
Camera power supply: DC 12V
Camera light: 12 pcs white LEDS
LEDs adjustable
Total Pixels: PAL: 720 x 576; NTSC: 720 x 480
Camera glass material: sapphire glass
Camera shell material: Aluminum alloy
Waterproof: IP68
Camera color: black and silver
Camera Head & Skids
Ø 1.575 in (40 mm) skid
Ø 3.15 in (80 mm) skid
Control box
DVR power supply: 12V
DVR work current: 200 mA
Storage medium: SD card (max 256GB)
Digital clock and digital calendar
Battery level indicator function
DVR Total Pixels: 720 x 576 (D1)
Picture snap and movie record
Movie format: MP4
USB stick (max 256GB)
AV1 and AV2 manually
Cable wheel
Cable size: ø 12.6 x 4.13 in (320 x 105 mm)
Wire material: fiberglass rod
Fiberglass length: 65.6 ft (20 m) (max 50 m)
Fiberglass diameter: ø 0.197 in (5 mm)
Fiberglass color: yellow red black blue
Charger
Input: AC 100-240 V ~ 50/60 Hz
Output: DC 12.6V / 1000 mA
DC plug diameter: 0.0827 in (2.1 mm)
Monitor
Monitor size: 7 inch TFT color monitor
Monitor Total Pixels: 800 x 480
Monitor power supply: DC 12V
Osd language: English
Battery level display
Up, down, left, right adjustable
16:9 & 4:3 model
Sunshade include

User’s Manual –AREBOS Pipe Inspection Camera System
6
LI-Ion Battery
Total Power: 14W
Charge time: 5 hours
Protective voltage: 8.1 V
Work time: ≧260 minutes
Cable connection
Size: Φ0.197 x 59.06 in (5 x 1500 mm)
GX16-6 and GX16-6 Elbow air head
Case
Size L x W x H: 18.9 x 16.34 x 7.87 in (480 x 415 x
200 mm)
Material: fire board + Aluminum alloy
Empty case weight: 7.5 lbs (3.4 kg)
Carton
Size: 19.29 x 8.27 x 18.3 in (490 x 210 x 465 mm)
Size: 20.28 x 16.73 x 17.72 in (515 x 425 x 450 mm)
Carton material: A = A paper
2.2 Control box

User’s Manual –AREBOS Pipe Inspection Camera System
7
1
AV1/AV2 switch
11
Menu left
2
Camera signal cable connector
12
Menu back
3
Video output
13
Menu
4
Recorded directory
14
Power control
5
Record/stop recording
15
Charge jack
6
Menu up
16
Microphone jack
7
Menu OK/pause/snap
17
Earphone jack
8
Menu right
18
USB stick jack
9
Menu down
19
SD card slot
10
LED brightness adjuster
Operation order:
•Press to switch on “USB STICK”, shows up.
•Press again to switch off “USB STICK”, disappears.
Attention:
•Turn off the unit before pull out the “USB STICK”.
•Do not use the “USB STICK” and “SD card” at the same time.

User’s Manual –AREBOS Pipe Inspection Camera System
8
3.Quick start guide
3.1 Charging the battery
•Connect the charger to the socket, the indicator of charger will turn into green (1).
•Connect the plug to the jack of control box (2).
•Turn the switch knob to “CHARGE” position (3).
•The indicator of charger will turn into red. When the Li-ion battery is full of power, the
indicator of charger will turn into green (4).
3.2 Starting up
•Open the suitcase and spread the sunshade (1).
•Connect the camera to the cable wheel (2).
•Connect one end to the control box (3).
•Connect the other end of connection wire to the cable wheel (4).
•Turn the switch knob to “ON/BATT” position (5).
•Switch to “AV1” (6).

User’s Manual –AREBOS Pipe Inspection Camera System
9
3.3 Checking waterproof ring & Assembling SKID
3.3.1 Check waterproof rubber ring on the bottom of the camera head
3.3.2 40 mm SKID and 23 mm camera head
•Set the SKID in the camera head (1).
•Fasten the SKID with a screwdriver by tightening its screws (2).
•The SKID assemble completed (3).
3.3.2 80 mm SKID and 23 mm camera head
•Set the SKID in the camera head (1).
•Fasten the SKID with a screw rod by tightening its screws (2).
•The SKID assemble completed (3).

User’s Manual –AREBOS Pipe Inspection Camera System
10
4.Recording and Menu
4.1 Inserting the SD card
•Warning: Pay attention to the direction of the SD card and plug it in as shown below!
4.2 AV1 & AV2 switch
•Press the “AV1/AV2”key on screen to switch the AV1 and AV2 mode.
•In AV1 mode, can both take picture and record video, in AV2 mode, can only monitor.

User’s Manual –AREBOS Pipe Inspection Camera System
11
4.3 Recording the video
•Press the “REC” button to start record video (1 & 2).
•Press the “REC” button again to finish the recording (3).
4.4 Recording the photo
•Press the “OK”button to snap a picture.
4.5 Playback video
•Press the “RECORDING DIRECTORY” button (1 & 2).
•Press the “OK” button to enter the “Video Files” (3).

User’s Manual –AREBOS Pipe Inspection Camera System
12
•Select the file you need (4).
•The monitor plays the video (5).
•Press the “OK” button to pause the video (6).
4.6 Playback photo
•Follow the same steps that the “Playback Video” has mentioned.

User’s Manual –AREBOS Pipe Inspection Camera System
13
4.7 Menu
•Press “menu” key enter into main menu.
Recorder Setting
System Setting
Event Playback
4.8 Recorder Setting

User’s Manual –AREBOS Pipe Inspection Camera System
14
•Work Mode
-Video: Record videos
-Photo: Snapshot photos
-Audio: Record audio
•Motion Detection
-Off: Stop the motion detection
-On: Start the motion detection
•Sensitivity
-High: Highest sensitivity
-Medium: Standard sensitivity
-Low: Lowest sensitivity
•Resolution
-720X576
-720X480
-640X480
•Video Quality
-High: High resolution
-Medium: Standard resolution
-Low: Low resolution
•Time Stamp
-Off: Time stamp will not be showed on the screen
-On: Time stamp will be shown on the screen
•Video Time
Length of the video recording
-5 minutes
-10 minutes
-15 minutes
-30 minutes
-60 minutes
•FPS Set
-15 FPS: 15 frames per second
-30 FPS: 30 frames per second
•Audio record volume
Work with audio record mode
-10 level can be adjusted
•Overwrite
-Off: The recording will be stop when the disk full
-On: The recording will overwrite old video files when the disk full

User’s Manual –AREBOS Pipe Inspection Camera System
15
4.9 System Setting
•Language
Select the operating language
•Date Time
Set the date and time, press OK to confirm
•Video Output
Choose whether PAL or NTSC to suit your monitor and TV Video Output
•Format
-No: The system will not format the SD card
-Yes: The system will format the SD card. (caution: PLS backup the data of the SD card before
operating).
•Firmware Update
-No: The system will not update the firmware
-Yes: The system will update the firmware
•Memory info
-All: The SD full capacity
-Free: The SD free capacity
•Default Setup
-No: Leaves set up as it is
-Yes: Factory resets the system
•Version
-Booc: 12.11.05 (soft version)

User’s Manual –AREBOS Pipe Inspection Camera System
16
4.10 Delete Files
•Please make sure the files you really want to delete, the files won’t be found after deleting.
•Press “Playback” key to find the files.
•Press “menu” to choose the file you want to delete, one and all.
•Press “OK” to delete it.
4.11 Zoom in & Zoom out the image (10 levels)
•Press navigation button “right”to zoom in the image^.
•Press navigation button “left”to zoom out the image.

User’s Manual –AREBOS Pipe Inspection Camera System
17
5.Troubleshooting Guide
Common Faults & Repair
•Video without sound
-Didn’t connect microphone or there are faults in microphone
-Didn’t connect earphone or there are faults in earphone
-Control box DVR abnormal
•Unable to input letters
-Too quick to restart control box
-There are faults in Control box USB plug
-There are faults in keyboard
-There are faults in control box PCB
•Able to input, but no image
-1.5 m connect wire disconnects
-There are faults in camera installation or Camera damage
-When press F2, the image has already switch to no-image type mode, press F3 return to
type mode
-Control box PCB board abnormal
•Time display error
-Control Box DVR board abnormal
•AV1 no image, AV2 display normally
-Control Box DVR abnormal
•AV1 no image, AV2 no image
-If 1.5 m connect wire connect between cable wheel and control box
-Does camera head screw tightly
-The aviation jack of control box that connected to monitor looses
-There are faults in monitor
-There are faults in control box DVR
•Battery is unable to be charged
-Charger didn’t insert correctly or there are faults in AC plug
-Please don’t use non-original charger
-There are faults in charger
-Li-ion battery damage
•The power of the battery runs out quickly
-Use the full power battery
-The capability of battery is low
•SD card cannot work
-Didn’t insert SD card correctly
-The write protection switch of SD card is open
-SD card is full, please replace SD card or transfer the files to free the space
-DVR SD card slot damage
•Turned on but no power
-Battery disconnects
-Fuse didn’t install or Fuse broke down
-There are faults in control box DVR

User’s Manual –AREBOS Pipe Inspection Camera System
18
•Display normally, Camera LED cannot light
-Camera didn’t install correctly
-There are faults in camera head
-There are faults in cable wheel
-There are faults in Control box PCB board
•Monitor cannot display
-Didn’t turn on monitor
-Monitor disconnects
-There are faults in monitor
-There are faults in control box
6.Disposal instruction
6.1 Disposal of the packaging
•Please make reference to the guidelines and standards for appropriate disposal of the packaging
valid in your region. In part, the package may consist of plastic bags - watch this respect, with
special care to ensure that this is not out of the reach of children. There is a risk of suffocation!
6.2 Disposal of waste equipment
•Equipment must be disposed of in accordance with the rules and regulations of the local waste
disposal.
6.3 Meaning of the "dustbin"
The symbol of the crossed-out dustbin on batteries or accumulators indicates
that they must not be disposed of with household waste at the end of their
service life. If batteries or accumulators contain mercury (Hg), cadmium (Cd) or
lead (Pb), you will find the respective chemical symbol below the symbol of the
crossed-out trash can. You are legally obliged to return old batteries and
accumulators after use. You can do this free of charge in a retail store or at
another collection point near you. Addresses of suitable collection points can be
obtained from your city or local government.
Batteries may contain substances that are harmful to the environment and
human health. Special care must be taken when handling batteries containing lithium due to the
particular risks involved. The separate collection and recycling of old batteries and accumulators is
intended to avoid negative effects on the environment and human health.
Please avoid the generation of waste from old batteries as much as possible, e.g. by preferring
batteries with a longer life or rechargeable batteries. Please avoid littering public spaces by not
carelessly leaving batteries or electrical and electronic equipment containing batteries. Please
consider ways to reuse a battery instead of disposing of it, for example by reconditioning or repairing
the battery.
You can also find more information on the Battery Act on the Internet at www.batteriegesetz.de.
You can also visit our website at www.arebos.de to find out about other return options we have
created.
Our customer service number: [phone]
Canbolat Vertriebs GmbH • Gneisenaustraße 10-11 • 97074 Würzburg

User’s Manual –AREBOS Pipe Inspection Camera System
19
EU Declaration of Conformity
We,
Canbolat Vertriebs GmbH, Gneisenaustraße 10-11, 97074 Würzburg, Germany,
Hereby declare that the product named below, seen its design and construction as well as according
to our sales, has been complied with the relevant and basic health and safety EU-requirements.
Name of the product: Arebos Pipe Inspection Camera System
Model Nr.: AR-HE-RK710USB
Art. Nr.: 4260551589454
If the product has any modification not allowed by us, this declaration loses its validity.
Tested acc. to:
EU Standard:
IEC62321-4:2013 EN 61000-3-2:2014
IEC62321-5:2013 EN 61000-3-3:2013
IEC62321-6:2015 EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
IEC62321-7:2015
EN 55032:2015+AC:2016
EN 55024:2010+A1:2015
EN 550535:2017
Date/Manufacturer Signature/Location: Würzburg, 04 Feb. 21
Identification of the signatory:
Korhan Canbolat, head of the company
Authorised representative for the technical documentation:
Korhan Canbolat
Office address:
Canbolat Vertriebs GmbH
Gneisenaustraße 10-11
D-97074 Würzburg
Return address can be found in the imprint: https://www.arebos.de/impressum/
VAT identification number: DE 263752326
Court of the Commercial Register is Würzburg, HRB 10082
WEEE Reg.-No. DE 61617071