Arecont Vision ConteraIP Fisheye AV12CPD-236 User manual

ConteraIP®Fisheye
Installation Manual
12MP
AV12CPD-236

1
Table of Contents
About Our Warranty ..........................................................................................................3
Global (3 Year) Limited Warranty .............................................................................3
Camera Overview..............................................................................................................4
Package Contents.............................................................................................................5
Installation.........................................................................................................................6
Surface Mount .........................................................................................................7
Wall Mount ..............................................................................................................9
Pendant Mount.......................................................................................................11
Pole Mount.............................................................................................................12
Corner Mount .........................................................................................................15
Camera Power Up...........................................................................................................17
Alarm I/O Functions.........................................................................................................18
Reset To Factory Default.................................................................................................18
Camera Discovery, Setup, and Configuration..................................................................19
Camera Discovery..................................................................................................19
Introduction to the Web Interface.....................................................................................20
Common ................................................................................................................21
Basic Info .........................................................................................................21
Local Settings...................................................................................................22
Network Configuration............................................................................................24
Ethernet ...........................................................................................................24
DNS .................................................................................................................26
Port ..................................................................................................................26
DDNS...............................................................................................................27
E-Mail...............................................................................................................27
SNMP...............................................................................................................28
802.1x ..............................................................................................................28
QoS..................................................................................................................29
Video & Audio ........................................................................................................30
Video................................................................................................................30
Snapshot..........................................................................................................32
Audio................................................................................................................33
ROI...................................................................................................................34
Media Stream...................................................................................................35
Image.....................................................................................................................36
Image ...............................................................................................................36

2
OSD .................................................................................................................44
Privacy Mask....................................................................................................45
Event Setting..........................................................................................................47
Common Alarm ................................................................................................47
Storage Setting ......................................................................................................56
Storage ............................................................................................................56
FTP ..................................................................................................................57
Security..................................................................................................................58
User .................................................................................................................58
Network Security ..............................................................................................59
System...................................................................................................................62
Time .................................................................................................................62
Ports & Devices................................................................................................63
Maintenance.....................................................................................................65
Importing and Exporting System Configuration File................................................67
Collecting Diagnosis Information ............................................................................68
Fisheye Camera Parameter ...................................................................................69
Live View.........................................................................................................................71
Live View Toolbar...................................................................................................72
Live View Display Mode .........................................................................................73
Video Playback and Download with SD Card Storage.....................................................75
Video Playback ......................................................................................................75
Download...............................................................................................................76
Dewarping in Video Management Software (VMS)..........................................................77
Dewarping in ConteraVMS.....................................................................................77
Dewarping in 3rd party VMS ..................................................................................80

3
About Our Warranty
Global (3 Year) Limited Warranty
ARECONT VISION COSTAR warrants to Purchaser a “Limited Warranty” that (a) each
Product shall be free from material defects in material and workmanship for a period of thirty-
six (36) months from the date of shipment, the “Warranty Period”; (b) during the Warranty
Period, the Product will materially conform with the specification in the applicable
documentation; (c) all "Licensed Programs" accompanying the Product will materially conform
with applicable specifications.

4
Camera Overview
ConteraIP® Fisheye Megapixel Cameras
The ConteraIP Fisheye provides an all in one solution for wide area video surveillance. The 12
mega pixel (MP) resolutions provide optimum performance. The housing is an outdoor rated
IP66 and IK-10 impact resistant dome enclosure. The ConteraIP Fisheye can replace multiple
fixed or PTZ cameras by recording an entire 360 degree field of view. With proper placement,
blind spots can be eliminated. With the ability to zoom into multiple regions of interests, the
return on investment can be easily measured. The ConteraIP Fisheye combines a day / night
mechanical IR cut filter with an integrated lens which provides excellent image quality
regardless of the time of day. For clear color images in low light conditions, NightView offers
strong low light sensitivity for capturing details in extremely low lit scenes, this is further
enhanced by the integrated LED illumination.
Arecont Vision®was the first to bring H.264 to the mainstream market and recently developed
SNAPstream™ (Smart Noise Adaptation and Processing) technology for reducing bandwidth
without impacting image quality. Today we are proud to offer our next generation H.265 with
SNAPstream+™ smart codec, capable of delivering high quality video while saving over 50%
of the data rate to reduce or prevent strain on the network.
The microSDXC slot supports up to 256GB of storage capacity for convenient onboard
storage. The camera can be powered via Power over Ethernet (PoE) using IEEE 802.3af
standards or 12V DC. The ConteraIP Fisheye is ONVIF Profile S, G and T compliant.
CAUTION!
1. Do not attempt to service a damaged unit yourself. Refer all servicing to qualified
service personnel.
2. Wiring methods shall be in accordance with the National Electrical Code/NFPA
70/ANSI, and with all local codes and authorities having jurisdiction. Wiring should be
UL Listed and/or Recognized wire suitable for the application.
3. Always use hardware e.g. screws, anchors, bolts, locking nuts etc. which are
compatible with mounting surface and of sufficient length and construction to insure
a secure mount.

5
Package Contents
•AV12CPD-236
•Cable Connection
IP
Network
Audio input
(Sound pickup)
Audio output
(Sound box)
Alarm input
(Voice activated switch)
Alarm output
(Alarm indicator)
RS485
Power adapter
Display
Mic
Housing
Mic
IR light
Dome bubble
Loudspeaker
Mic
Description
QTY
AV12CPD-236 camera
1
Quick Start Guide/ Mounting Template
1
Accessory Pack
2

6
•Micro SD Card Slot and Reset Button
•Waterproof Cable

7
Installation
Surface Mount
1. Determine a secure location to mount the camera.
2. Press the lock button and remove the dome cover as shown in the figure below.
3. Optional: Remove the cover plate shown below and insert a micro SD card.
4. Use the provided template, anchors and screws to prepare the installation surface.
Lock button

8
5. Connect all necessary cables.
6. Mount the camera using the provided screws.
7. Reattach the dome cover.
8. To configure the camera, reference the camera discovery, set-up and configuration
section.
CAUTION!
The captive screws must be used to properly secure the dome cover and camera
housing. Failure to use the captive fastener may result in serious injury. When
mounting the dome cover to the camera housing, ensure that the gasket is properly
sealed and not folded. Failure to do so may result in water and dust ingress. Water
damage from improper installation is not covered by the warranty!
Lock button

9
Wall Mount
For proper installation the AV-WMJB-W and CF-CAP-W are required (sold separately). The
wall mount should be mounted to hard surfaces only (i.e. wood, metal, and concrete).
1. Use the provided template, anchors and screws to prepare the installation surface.
2. Thread the CF-CAP-W onto the AV-WMJB-W.
NOTE: The thread size for Top shield, pendant pole and mount is 1.5” NPT.
3. Attach the wall mount to the surface using the provided screws or use suitable
hardware for the mounting surface.
4. Run all necessary cables through the wall mount. Ensure the gasket is sealed
properly.
5. Press the lock button and remove the dome cover as shown in the figure below.
Lock button

10
6. Optional: Remove the cover plate shown below and insert a Micro SD card.
7. Connect all necessary cables.
8. Install the camera into the CF-CAP-W with the (3) supplied screws.
9. Reattach the dome cover.
10. To configure the camera, see Camera Discovery, Setup and Configuration on page 18.
CAUTION!
The captive screws must be used to properly secure the dome cover and camera
housing. Failure to use the captive fastener may result in serious injury. When
mounting the dome cover to the camera housing, ensure that the gasket is properly
sealed and not folded. Failure to do so may result in water and dust ingress. Water
damage from improper installation is not covered by the warranty!

11
Pendant Mount
For proper installation the AV-PMJB-W and CF-CAP-W are required (sold separately). The
pendant mount should be mounted to hard surfaces only (i.e. wood, metal, and concrete).
1. Use the provided template, anchors and screws to prepare the installation surface.
2. Thread the CF-CAP-W, pendant pole and AV-PMJB-W together.
NOTE!
The thread size for Top shield, pendant pole and mount is 1.5” NPT.
3. Attach the pendant mount to the surface using the 4 wood screws or use suitable
hardware for the mounting surface.
4. Run all necessary cables through the pendant mount. Ensure the gasket is sealed
properly.
5. Press the lock button and remove the dome cover as shown in the figure below.

12
6. Optional: Remove the cover plate shown below and insert a Micro SD card.
7. Connect all necessary cables.
8. Install the camera into the CF-CAP-W with the (3) supplied screws.
9. Reattach the dome cover.
10. To configure the camera, see Camera Discovery, Setup and Configuration on page 18.
CAUTION!
The captive screws must be used to properly secure the dome cover and camera
housing. Failure to use the captive fastener may result in serious injury. When
mounting the dome cover to the camera housing, ensure that the gasket is properly
sealed and not folded. Failure to do so may result in water and dust ingress. Water
damage from improper installation is not covered by the warranty!
Lock button

13
Pole Mount
For proper installation the AV-WMJB-W, AV-PMA-W and CF-CAP-W are required (sold
separately). The pole mount should be mounted to hard surfaces only (i.e. wood, metal,
and concrete).
1. Using the provided template, anchors and screws to prepare the installation surface.
2. Connect the wall mount cap and wall mount.
3. Attach the Junction Box Adapter to the Pole Mount Adapter.
4. Remove the conduit plug on the junction box adapter and connect ¾” NPT conduit to
the junction box adapter.
5. Run the Ethernet cable and outside power cable (if necessary) through the Junction
Box Adapter. Ensure the gasket is seated properly.
Reference #
Description
1 Remove conduit plug
2 Connect ¾” NPT conduit to junction box adapter (ensure use of water
seal tape).
NOTE!
Use silicon and / or thread seal tape between the conduit pipe and junction
box adapter.

14
6. Attach the Wall Mount Adapter (AV-WMJB-W) to the Pole Mount Adapter (AV-PMA-
W).
7. Use the supplied two Steel Straps to attach the Pole Mount Adapter to the pole and
tighten the compression screws.
8. To attach the camera to the Wall Mount Adapter (AV-WMJB-W), reference the
Installation and Wall Mount section.
9. To configure the camera, reference the camera discovery, set-up and configuration
section.
CAUTION!
The captive screws must be used to properly secure the dome cover and camera
housing. Failure to use the captive fastener may result in serious injury. When
mounting the dome cover to the camera housing, ensure that the gasket is properly
seated and not folded. Failure to do so may result in water and dust ingress. Water
damage from improper installation is not covered by the warranty!

15
Corner Mount
For a corner mount installation, the AV-WMJB-W wall mount, AV-CRMA-W corner mount, and
CF-CAP-W mount cap are required (sold separately). A corner mount should only be attached
onto hard corner surfaces including wood, plastic, metal, and concrete.
1. Using the Mounting template, prepare the mounting provisions for the camera
installation.
2. Connect the wall mount cap and wall mount.
3. Attach the Junction Box Adapter to the Corner Mount Adapter.
4. Remove the conduit plug on the junction box adapter and connect ¾” NPT conduit to
the junction box adapter.
NOTE! Use silicon or water pipe seal tape to make sure no water leakage between
conduit pipe and junction box adapter.
Reference #
Description
1 Remove conduit plug
2
Connect ¾” NPT conduit to junction box adapter (ensure use of water
seal tape)

16
5. Run the Ethernet cable and outside power cable (if necessary) through the Junction
Box Adapter. Ensure the gasket is seated properly.
6. Attach the Wall Mount Adapter (AV-WMJB-W) to the Corner Mount Adapter (AV-
CRMA-W).
7. Using the screws provided (or other hardware), attach the Corner Mount Adapter to an
exterior 90 degree corner wall.
8. To attach the camera to the Wall Mount Adapter (AV-WMJB-W), reference the
Installation and Wall Mount section.
9. To configure the camera, reference the camera discovery, set-up and configuration
section.
CAUTION!
The captive screws must be used to properly secure the dome cover and
camera housing. Failure to use the captive fastener may result in serious injury.
When mounting the dome cover to the camera housing, ensure that the gasket
is properly seated and not folded. Failure to do so may result in water and dust
ingress. Water damage from improper installation is not covered by the warranty!

17
Camera Power Up
CAUTION!
This product should be installed by a qualified service technician in accordance with
the National Electrical Code (NEC 800 CEC Section 60) or applicable local code.
Wiring methods shall be in accordance with the National Electrical Code/NFPA
70/ANSI, and with all local codes and authorities having jurisdiction. Wiring should
be UL Listed and/or Recognized wire suitable for the application.
CAUTION!
Make the connections inside a watertight compartment. Isolate unused power wires
individually. After connections are made, ensure that the watertight compartment is
tightly closed and cables and conduits are properly sealed to prevent ingress of
water.
1. Power the camera.
There are two options to power the camera:
a. Connect the camera to a 100/1000Mbps PoE switch using Ethernet cabling.
b. Power the camera via 12VDC.
2. Connect the PoE switch to your computer’s network port using an Ethernet cable.
LED
Status
Description
Green
Quick Flashing
Link has been established
Slow Flashing
Normal operation
None
None
No Connection

18
Alarm I/O Functions
Connect the Alarm In (DI) connector to the alarm input sensor, and connect Alarm Out (DO)
connector to the alarm output signal. To avoid any damaged, please follow the specification
of the part as below:
Alarm In (Wet Contact)
Alarm Out (Wet Contact)
DC
AC
V sense V sense I sense V sense I sense
5V 30V 1A (max) 125V 0.3A (max)
Reset to Factory Default
There are 2 methods to factory default the camera.
•Reset button
NOTE!
The reset button only works within ten minutes of the camera startup.
1. Remove the cover plate.
2. Press and hold the reset button for 15 seconds.
•Camera Web Interface
1. Access the camera web interface (Default IP is 192.168.1.13)
2. Login with (admin / AVCostar)
3. Click Setup > System > Maintenance > Default.

19
Camera Discovery, Setup, and Configuration
NOTE!
Use AV IP Utility
(http://www.arecontvisoin.com/softwares.php) to locate the camera on the network.
All configuration must be performed from the camera web interface.
Disable 3rd stream in the camera web page if you are using ConteraVMS. Refer to
Dewarping in Video Management Software (VMS) on Page 80.
Camera Discovery
NOTE!
If there is no DHCP server on the network the default IP address is 192.168.1.13
Default username: admin
Default password: AVCostar
1. Launch AV IP Utility.
2. When the program launches, it will perform an automatic discovery and display all
cameras found.
3. Double click on the IP address of the camera you wish to configure or manually launch
a web browser and type in the IP address.
Note!
Internet Explorer must be used if live streaming is required due to an ActiveX plugin
needing to be installed.