Argos Home Highsleeper Brooklyn 8545639 User manual

Highsleeper - Brooklyn
Dimensions
Length - 200,4cm
Depth - 106cm
Height - 184,7cm
Weight - 47kg
Issue 1 - 22/06/18
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
0045 7668 8055 or e-mail: order@flexa.dk
Assembly Instructions - Please keep for future reference 8545639

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could
damage the unit. Only use hand
screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
1
IMPORTANT - READ CAREFULLY -RETAIN FOR FUTURE REFERENCE
ASSEMBLY:
Always follow the instruction. Current legislation requires that the high bed / bunk bed must be fitted with 4
safety-rails and a ladder or platform for the upper bunk. The high bed / bunk bed meets the European EN
747:2012 A1:2015 standards for security and durability.
MATTRESS:
This bed is designed to use a mattress size 190 cm long and 90 cm wide. The total thickness must not
exceed 19,5 cm. The mattress top must not pass the marking on the ladder / the post for the safety-rail.
WARNING:
High beds and the upper bed of bunk beds are not suitable for children under six years due to the risk of
injury from falls. Bunk beds and high beds can present a serious risk of injury from strangulation if not used
correctly. Never attach or hang items to any part of the bunk bed that are not designed to be used with the
bed, for example, but not limited to ropes, strings, cords, hooks, belts and bags. Children can be become
trapped between the bed and the wall, a roof pitch, the ceiling, adjoining pieces of furniture (e.g. cupboards)
and the like. To avoid risk of serious injury the distance between the top safety barrier and the adjoining
structure shall not exceed 75 mm or shall be more than 230 mm.
Do not use the high bed / bunk bed if any structural part is broken or missing.
MAINTENANCE INSTRUCTIONS:
Check regulary that all assembly fastenings are properly tightened. Ventilation of the room is necessary in
order to keep the humidity low and to prevent mould in and around the bed.

2
Endrail x2
(86,5x5,5x5,5cm) Endrail x2 (86,5x8,9x2,0cm)
Ladder side x2
(179,3x8,9x2,0cm)
7 8
9
Short post x1
(35,3x4,3x4,3cm)
3
Components - Parts
Please check you have all the parts listed below
Tread x4 (31,8x6,5x2,6cm)
1
Filling x2 (86,5x29,8x0,8cm)
4
No. 12-04303531-65
Endrail x2 (86,5x8,9x2,0cm)
2No. 12-02008653-65
Slat x18 (89,7x5,5x1,1cm)
5No. 12-01108971 Top rail x2
(100,2x8,2x2,4cm)
6
No. 12-02410021-65
No. 12-05508651-65 No. 12-020086510-65
No. 12-02017931-65
If you have damaged or missing components,
call the Customer Helpline:
0045 7668 8055
No. 12-02603182-65
No. 4301-0808653-65

Bedside x2
(186.7x8.9x2.0cm)
Leg x2
(182,3x5,5x5,5cm) Leg x2 (182,3x5,5x5,5cm)
Safety rail x3
(186.7x8.9x2.0cm) Safety rail x2 (146,6x8.9x2.0cm)
10
13 14
11 12
No. 1305-186710-65
No. 12-05518231-65 No. 12-05518232-65
No. 12-02018672-65 No. 12-02014661-65
Components - Parts
Please check you have all the parts listed below
If you have damaged or missing components,
call the Customer Helpline:
0045 7668 8055
3

Components - Fittings
Please check you have all the fittings listed below
M6x100mm Connecting bolt x12
Tools required
A
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
M6 ø10x14mm Barrel nut x12
B
E
4,0x30mm Chipboard screw x36
C
10x50mm Dowel x36 8x50mm Dowel x4
D
Phillips
screwdriver
(medium)
Small
hammer
Allen key
4mm incl.
Flatblade
screwdriver
(medium)
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
G
JK L
MN
F
O
P
S
Q R
I
H
4,0x70mm Chipboard screw x8
4,0x30mm Chipboard screw x10 4,0x25mm Chipboard screw x4 6,3x22mm Euro screw x4
7,0x50mm Confirmat screw x16 7,0x80mm Confirmat screw x1
Ø8mm Cover cap x16
Ø10 Cover cap x16
70x40,5x20mm Angle x2
Ø7 Cover cap x16
Bracket x2 27,5x17x15mm Angle x4
6,3x105mm Assembly screw x16
No. 3901-40030 No. 3903-40025 No. 3907-63022
No. 3908-70050 No. 3908-70080
No. 3938-000081-19
No. 3938-00010-19
No. 4008-022
No. 3938-00007-19
No. 4007-024 No. 4008-020
4
No. 3902-40030
No. 3930-10050
No. 3922-06014
No. 3913-06100
No. 4033-004
No. 3930-08050
No. 3909-631051 No. 3901-30020
No. 3901-40070
3,0x20mm Chipboard screw x2

Insert the dowels Dinto
the holes in bedsides 10 ,
safety rails 11 and 12
and endrails 8and 7.
Insert Ø8 dowels Einto
the holes in endrail 7.
It may be necessary
to tap the dowels in
very gently with a small
hammer.
Attach endrails 7to top
rails 6using screws G.
Don’t overtighten.
Attach leg 13 to endrail
7using the inserted
dowel only.
Attach endrail 8and
filling 4to leg 13 using
the inserted dowel only.
Assembly Instructions
Step 1
Step 2
Step 3
813
4
7
7
6
G
G
G
G
10
11
12
8
7
D
D
D
D
D
D
D
D
D
D
E
E
Ø10
Ø8
G
15 Holes up!
5
E
D

6
13
H
H
H
H
H
H
Attach leg 14 to endrails
7and 8. At the same
time attach endrail 2
between the legs 13 and
14
Insert assembly screws
Hand fasten with
the allen key. Don’t
overtighten.
Attach bedside 10 and
safety rails 11 to the bed
by placing the dowels
into the holes in legs 13
and 14 .
Push 2 barrel nuts B
into the small holes in
bedside 10 and safety
rails 11 , note that the
barrel nuts should be
facing outwards on
the safety rails. Push
1 connecting bolt A
through legs 13 and 14
to meet the barrel nuts B
and fasten with the allen
key.
Step 5
Assembly Instructions
Step 4
A
B
7
8
4
14
14
2
13
10
11
11
11
B
B
BB
B
B
B
B
AAA
A
A
A
A
A
15 Holes up!
H

Assembly Instructions
Attach the second
bedside 10 to the bed by
placing the dowels into
the holes in legs 13 and
14 as in the previous
step.
Push 2 barrel nuts B
into the small holes
in bedside 10 . Push
1 connecting bolt A
through legs 13 and 14
to meet the barrel nuts B
and fasten with the allen
key.
Attach safety rails 12 to
the bed by placing the
dowels into the holes in
leg 14 .
Push 2 barrel nuts B
into the small holes in
safety rails 12 . Push
1 connecting bolt A
through legs 14 to meet
the barrel nuts Band
fasten with the allen key.
Attach short post 3to
the bed by placing the
dowels in safety rails 12
into the holes in short
post 3. Insert screw
Ninto the hole in short
post 3and fasten with
the allen key. Don’t
overtighten. Attach the
short post 3to the
bedside 10 using the
screws J.
Step 6
Step 7
10 13
14
12
12
14
10
3
3
A
ABB
N
J
J
J
N
7
A
A
B
B
A
A
B
BLadder can be positioned
left or right!!

8
Assembly Instructions
Attach the treads 1to
the ladder sides 9using
the screws M.
Attach brackets Qto the
ladder sides 9using the
screws J.
Attach angles Rto the
ladder sides 9using the
screws L.
Place the assembled
ladder into the bed.
Fasten brackets Qto
the bedside 10 using the
screws I.
Attach the ladder to the
leg and short post using
screws Kthrough the
angles R.
Step 8
Step 9
R
R
R
R
L
L
L
L
M
M
M
M
M
M
M
M
Q
Q
J
J
13
9
9
9
1
1
1
1
9
I
I
K
K
KK
J
L
M
Q
R
K
I

798 mm 904 mm
Assembly Instructions
Place two slats 5in the
ends of the bed, against
the legs. Fasten with four
chipboard screws C.
Place one slat 5in
the bed. Follow the
measurements.
Push the bedsides 10
together whilst attaching
middle slat 5to the
bed with two chipboard
screws C.
Position the remaining
fifteen slats 5in the
bed with an approximate
distance of 52 mm
between each.
Fasten each slat with two
screws C
Step 10
Step 11
5 5 5 5 55 5 5 55 5 5 55 5 5 5 5
C C
C
C
C
C
C
52 mm
5
10
10
9