Argos Home Mia 2261490 User manual

Assembly Instructions - Please keep for future reference
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Argos Customer Helpline: 0845 640 30 30
White 2261490
Issue 1 - 25-05-2014
Mia Workdesk
Dimensions
Width
Depth
Height
:
:
:
350271
124.5 cm
55.0 cm
76.0 cm

!Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Care and maintenance
1
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• We do not recommend the use
of power drill/drivers for
inserting screws, as this could
damage the unit. Only use hand
screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page
with these instructions for
future reference.

Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call
the Argos Customer Helpline: 0845 640 30 30
2
350271-03
2
(15,5 cm x 45,6 cm)
Side, left
10
(35 cm x 9,8 cm)
Drawer side, right/left
2
x
1
(124,5 cm x 55 cm)
Top
3
(15,5 cm x 45,6 cm)
Side, right
7
(111,5 cm x 6 cm)
Front rail
8
(111,5 cm x 15,5 cm)
Back rail
4
x
9
(55,3 cm x 14,5 cm)
Drawer front
11
(50,8 cm x 9,8 cm)
Drawer back
12
(51,8 cm x 34,7 cm)
Drawer bottom
2
x
2
x
2
x
4
(74,5 cm x 5,0 cm)
Leg, left
5
(74,5 cm x 5,0 cm)
Leg, right
2
x
6
(13,8 cm x 44,1 cm)
Divider

Components - Fittings
Please check you have all the panels listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more ttings
may be supplied than are required.
3350271-04
24 ø8 x 40mm Wooden dowel x
Aa Ab
ø6 x 30mm Wooden dowel x 8
Cp
ø5 x 11, cc34mm Bolt x 24
Ca
ø15 x 10.5mm Cam x
24
Hk
4
M4 x 9mm Screw x
Kb
ø5.8 x 8mm Screw x
6
Sk
4 245 x 17 x 10mm Drawer runner x
17060 16040 90 15013070 120100 14011050 803020100
Ruler - Use this ruler to help correctly identify the screws
Tools required
Flatblade screwdriver
(Medium)
Hammer Phillips screwdriver
(Medium & large)
Back fitting w. ø3.5 x 15mm Screw x
Fi
4
ø3 x 35mm Screw x
Bp
8
Wall strap and instruction x 1
Fh
ø10 x 9mm Spacer x
Nu
6
Kf
6
ø5.8 x 19mm Screw x
ø5 x 38mm Screw x
Dj
2

Assembly Instructions
Place the legs 4and
5onto the sides 2
and 3.
Push cams
Ca
into the
holes indicated on the
sides 2and 3.
Arrows pointing towards
the legs 4/5.
Turn the cams
Ca
to the
right to x the legs 4
and 5.
Step 1.3
Assembly of the desk.
Step 1
Knock the dowels
Aa
into the holes indicated
on the sides
2
and
3
using a small hammer.
Step 1.1
Screw the bolts
Cp
into
the holes indicated on the
legs
4
and
5
.
Step 1.2
4
350271-05
16 ø8 x 40mm Wooden dowel x
Aa
3
5
4
2
4
2
5
13
5
Cp
ø5 x 11, cc34mm Bolt x 8
Ca
ø15 x 10.5mm Cam x
8
3
2
8
74
5
4
5
4
Ca Ca
Cp
Cp
Aa
Aa
Aa Aa
Aa
2
x
2
x
6
Aa
Aa
Aa
Ca Ca
Ca Ca
Ca Ca

Assembly Instructions
Slide the top of the
drawer runners
Sk
backwards. You can
identify the front end of
the drawer runner
Sk
by
the two M4 holes. See
details.
Place the Spacers
Nu
as shown, and x the
front end of the drawer
runners
Sk
to the sides
2and 3using screws
Kf
through the holes
number 2 and 8 as
indicated.
See details.
Step 1.5
Screw the bolts
Cp
into
the holes indicated on the
sides
2
and
3
.
Step 1.4
350271-06
5
Front end
Sk
Sk
2 245 x 17 x 10mm Drawer runner x
2
ø10 x 9mm Spacer x
Nu
4
Kf
4
ø5.8 x 19mm Screw x
Sk
Sk
3
2
Cp
ø5 x 11, cc34mm Bolt x 6
Cp
Cp
Cp
Cp
Kf
Sk
Sk
Kf
Nu
Nu
Front end
Cp
Cp
Kf
Kf
Nu
Nu
Front end
Hole no. 2
Hole no.
8
Hole no.
2
Hole no.
8

Assembly Instructions
Slide the top of the draw-
er runners
Sk
forwards.
Place the Spacers
Nu
as shown, and x the
back end of the drawer
runners
Sk
to the sides
2and 3using screws
Kf
through the holes
indicated.
See details.
Step 1.6
Knock the dowels
Aa
into
the holes indicated on
the back rail
8
, the front
rail
7
and the divider
6
using a small hammer.
Step 1.7
6
350271-07
ø10 x 9mm Spacer x
Nu
2
Kf
2
ø5.8 x 19mm Screw x
Aa
Aa
7
8
Aa
Aa
Kf
Kf
3
2
8 ø8 x 40mm Wooden dowel x
Aa
Aa
Aa
6
Nu
Nu

Assembly Instructions
Slide the top of the drawer
runner
Sk
backwards.
Identify the front end of the
drawer runner
Sk
by the two
M4 holes.
Fix the front end of the
drawer runner
Sk
to the
divider
6
using screws
Kb
through the holes number 2
and 8 as indicated.
Step 1.8
Slide the top of the drawer
runner
Sk
forwards.
Fix the back end of the
drawer runner
Sk
to the
divider
6
using screw
Kb
through the hole indicated.
Step 1.9
Turn the divider
6
upside
down.
Slide the top of the drawer
runner
Sk
forwards.
Fix the front end of the
drawer runner
Sk
to the
divider
6
using screws
Kb
through the holes number 2
and 8 as indicated.
Step 1.10
Slide the top of the drawer
runner
Sk
forwards.
Fix the back end of the
drawer runner
Sk
to the
divider
6
using screw
Kb
through the hole indicated.
Step 1.11
350271-08
7
Sk
1 245 x 17 x 10mm Drawer runner x
Kb
ø5.8 x 8mm Screw x
2
Kb
ø5.8 x 8mm Screw x
4
Sk
Front end
Sk
1 245 x 17 x 10mm Drawer runner x
Kb
ø5.8 x 8mm Screw x
1
Kb
ø5.8 x 8mm Screw x
2
6
6
6
6
Kb
Kb
Kb
Sk
Sk
Kb
Kb
Kb
Sk
Sk
Hole no. 2
Hole no. 8
Hole no. 2
Hole no.
8

Assembly Instructions
Place the sides 2and
3onto the back rail 8
and the front rail
7.
Push cams
Ca
into the
holes indicated on the
back rail 8and the front
rail
7.
Arrows pointing towards
the sides 2/3.
Turn the cams
Ca
to the
right to x the sides 2
and 3.
Step 1.14
Screw the bolts
Cp
into
the holes indicated on the
top
1
.
Step 1.12
Place the divider 6onto
the top
1.
Push cams
Ca
into
the holes indicated on
the divider 6. Arrows
pointing towards the
top 1.
Turn the cams
Ca
to the
right to x the divider 6.
Step 1.13
8
350271-09
Ca
ø15 x 10.5mm Cam x
6
Ca Ca
Ca
Ca
3
7
8
2
1
Cp
Cp
Cp
Cp
Cp
Cp
Ca Ca
Ca
ø15 x 10.5mm Cam x
2
1
6
Ca
Ca
Cp
ø5 x 11, cc34mm Bolt x 6

Assembly Instructions
Step 1.17
!
Important!
The work desk is
heavy.
Lift with care.
Its recommended that the
work desk is xed to the
wall.
Use the ttings
Fh
. Follow
the instructions included
with the ttings.
Place the sides 2and
3onto the top 1.
Push cams
Ca
into the
holes indicated on the
sides 2and 3.
Arrows pointing towards
the top 1.
Turn the cams
Ca
to the
right to x the top 1.
Step 1.15
Fix the back rail 8and
the front rail 7to the
divider 6as shown,
using screws
Dj
.
Step 1.16
350271-10
9
Wall strap and instruction x 1
Fh
Ca
ø15 x 10.5mm Cam x
4
1
3
2 Ca
Ca
Ca
ø5 x 38mm Screw x
Dj
2
Dj
Dj
87
6