Argos Home Scandinavia 642/3753 User manual

Page 1 of 17
Scandinavia
5+5 drw. chest
Scandinavia 5+5 drw. chest
400mm
1052mm
933mm

Please sort out all parts before you begin to assemble the item.
This to make sure you always use the correct part.
Fittings contained in the box.
Tools needed.
A12 pcs. Cam - ø15 x 12mm B40 pcs. Cam - ø12 x 10,5mm C52 pcs. Bolt - ø6,5 x 24/11mm
D60 pcs. Screw - ø4 x 13mm E55 pcs. Screw - ø3,5 x 35mm
G30 pcs. Nail - 1,2 x 20mm H10 pcs. Plastic runner - 340mm
L1 pcs. Joining strip - 940mm
J15 pcs.
0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
190
200
210
220
230
240
250
260
270
MM
Hazard Warning !
Keep small components out of the reach of children.
Fittings A, B, C, D, E, F and G are shown in their actual dimensions.
F6 pcs. Dowel - ø6 x 30mm
K10 pcs. Plastic Runner - 340mm
Knob
ø40 x 30mm
Page 2 of 17Scandinavia 5+5 drw. chest
M1 pcs. Nail guide

Wooden parts contained in the box.
1 pcs.
5Divider
2 pcs.
6Back
5 pcs.
7Drawer front, large
5 pcs.
8Drawer front, small
1 pcs.
3Top
2 pcs.
4Plinth.
5 pcs.
13 Drawer bottom, large
5 pcs.
14 Drawer bottom, small
5 pcs.
9Drawer back, large
5 pcs.
10 Drawer back, small
10 pcs.
12 Drawer side, right
10 pcs.
11 Drawer side, left
1 pcs.
1Side, left 1 pcs.
2Side, right
Page 3 of 17Scandinavia 5+5 drw. chest
919x370mm
1052 x 400mm
942 x 55mm
794x366mm
960 x 400mm
606 x 157mm
314 x 157mm
579 x 92mm
286 x 92mm
342 x 107mm
342 x 107mm
589 x 339mm 297 x 339mm
919x370mm

No.3 "Shield Anchor" Wall Plug
Heavy Loads
For use with heavier loads such as TV
& HiFi Speakers and Satellite Dishes etc.
No.4 "Cavity Fixing" Wall Plug
For use with plaster board partitions or
hollow wooden doors.
No.5 "Cavity Fixing - Heavy Duty"
Wall Plug
For use when fitting or supporting heavy
loads such as shelving, wall cabinets,
coat racks.
IMPORTANT:
When drilling into walls always check that there are no
hidden wires or pipes etc. Make sure that the screws and
wall plugs being used are suitable for supporting your unit.
Consult a qualified tradesperson if you are unsure.
HINTS:
1) General Rule Always use a larger screw and wall plug if you are not sure.
2) Ensure you use the recommended drill bit to match the wall plug and hole size.
3) Ensure you drill the hole horizontally, do not force the drill or enlarge the hole.
4) Take extra care when drilling high walls, ceilings and ceramic tiles. Ensure the plug is fitting below the ceramic
tile to avoid splitting or cracking.
5) Ensure wall plugs are well fitted and are a tight fit in the drilled hole.
Types Of Walls
You can use one of the following types
of wall plug if your walls are made of
brick, breeze block, concrete, stone,
wood or plaster board.
No.1 "Standard" Wall Plug
General Wall Materials
These come in various sizes and are made
from plastic or sometimes wood fiber.
No.2 "General Purpose" Wall Plug
Aerated / Breeze Block
Generally aerated blocks should not be
used to support heavy loads, use a
specialist fitting in this case.
For light loads, a General Purpose Plug
can be used.
No.6 "Hammer Fixing" Wall Plug
For use with walls stuck with plaster
board. The hammer fixing allows it to
be fixed to the wall rather than the plaster
board. Always check the fixing is secure
to the retaining wall.
CARE & MAINTENANCE
SAFETY
Always check the fitting and
location to ensure your safety in
and around the home.
FITTING
From time to time check the fitting
to ensure the wall plugs or screws
do not become loose.
Wall Mounting & Fixings
A Guide to
Page 4 of 17
Scandinavia 5+5 drw. chest

1
2
3
4
4
5
6
6
7
8
9
10
11
11
12
12
13
14
Key diagram.
Function of cam & bolt.
Page 5of 17Scandinavia 5+5 drw. chest
134
2
Step 2:
Push the wooden panel
with the attached bolt onto
the other wooden panel.
Step 4:
Tighten: Turn the cam to
the right.
Step 1:
Fix the bolt to the
wooden panel.
Step 3:
Place the cam into the
hole, arrow pointing
towards the bolt.
L
x 5
x 5

1. Inserting the dowels to the plinths.
2. Mounting the bolts to the plinths.
3. Mounting the bolts to the sides.
F
4 pcs.
C
2 pcs.
C
4 pcs.
F
C
C
C
Page 6 of 17Scandinavia 5+5 drw. chest
4
2 pcs.
Knock the dowels "F"
into the holes
indicated on both the
plinths "4".
Screw the bolts "C" into
the hole indicated on
both the plinths "4".
Screw the bolts "C" into
the holes indicated on
the sides "1" & "2".
4
2 pcs.
1
Side, left
2
Side, right

4. Mounting the plastic runners to the sides.
D
10 pcs
H
10 pcs
D
10 pcs
D
D
10 pcs
Page 7of 17Scandinavia 5+5 drw. chest
DD
D
Fig. 4.1
Fix the plastic runners
"H" to the sides "1" and
"2", using screws "D".
The dowel should be
pointing towards the
sides.
Start fixing the ends of
the plastic runners to
the sides as shown in
fig. 4.1
Finally fix the plastic
runners using the
central holes.
1
Side, left
2
Side, right
H
Plastic runner type "H"
note the dowel.
H
Dowel

5. Adding the plinths to the right hand side.
6. Assembling the left hand side to the plinths.
Fig. 5.1
A
2 pcs.
A
2 pcs.
Fig. 5.2
Page 8of 17Scandinavia 5+5 drw. chest
A
A
2
Side, right
4
Plinth
4
Plinth
Bolt "C"
Press the plinths "4"
onto the side "2".
See page 4 "Function of
the cam & bolt".
Place the cams "A" into
the holes indicated,
arrows pointing towards
the side / bolt.
Tighten:
Turn the cam to the right.
Fig. 5.2
4
Plinth
4
Plinth
2
Side, right
1
Side, left
Bolt "C"
Press the side "1" onto
the two plinths "4".
See page 4 "Function
of the cam & bolt".
Place the cams
"A" into the holes
indicated, arrows
pointing towards the
side / bolt.
Tighten:
Turn the cam to the
right. Fig. 5.2
Rabbet = Back

7. Inserting the dowels to the divider.
8. Mounting the plastic runners to the divider - part 1.
D
5 pcs.
D
5 pcs.
F
2 pcs.
F
D
DD
Fig. 8.1
Page 9of 17Scandinavia 5+5 drw. chest
D
5 pcs.
Knock the dowels "F"
into the holes indicated
on the divider "5".
Fix the plastic runners
"K" to the left hand
side of the divider "5",
using screws "D".
First use the two holes
in the plastic runners
nearest to the ends.
The holes mentioned
above should both fit
the holes in the divider.
See fig. 8.1
5
Divider
5
Divider K
Plastic runner type "K"
NO dowel

9. Mounting the plastic runners to the divider - part 2.
10. Mounting the bolts to the top.
D
5 pcs.
D
D
D
D
Fig. 9.1
D
5 pcs.
D
5 pcs.
C
6 pcs.
3
Top
Page 10 of 17Scandinavia 5+5 drw. chest
C
C
C
C
C
Turn around the divider.
Fix the plastic runners
"K" to the right hand
side.
First use the two holes in
the plastic runners
placed second from the
ends.
The holes mentioned
above should both fit the
holes in the divider.
See fig. 9.1
Screw the bolts "C" into
the holes indicated on
the top "3".
5
Divider
K
Plastic runner type "K"
NO Dowel
K
5 pcs.