Argos Home Normandy 4 Drawer Chest of Drawers User manual

MADE IN
BRITAIN
Dimensions
4 Drawer Chest
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Important - Please read these instructions fully before starting assembly
227/6478
266/2185
244/2941
Width - 75cm
Depth - 40cm
Height - 74.5cm
NEW MK2 VERSION
Issue 2 - 05/03/13 - Rebates taken off,Top Rail removed, panel numbers updated.
Issue 4 - 09/09/14
ALR3008
Issue 3 - 03/04/14 - Drawer box sizes increased.
Add 16 wedges.
Add 4 plastinails.
Remove old cat codes and add new ones.
Issue 4 - 09/09/14 - Removed‘Anderson’from the title so it can be used for both Anderson and Normandy.
Added 3 new cat codes for Normandy.
349/8042
356/9304
343/2709

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 26kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Panels
Please check you have all the panels listed below
2
1
100%
4
6Drawer Front (D0218A)
(737 x 162mm) x 4
2
3
5
10
9
Drawer Base (T695-367)
(695 x 367mm) x 4
Drawer Back (W684-124)
(684 x 124mm) x 4
Rail (D2201A)
(717 x 60mm) x 2
Top (D2200A)
(750 x 396mm)
Left Side (D2198A)
(721 x 372mm)
Right Side (D2199A)
(721 x 372mm)
Back (X741-700)
(741 x 700mm)
78
Left Drawer Side
(W370-124LH)
(370 x 124mm) x 4
Right Drawer Side
(W370-124RH)
(370 x 124mm) x 4

Please check you have all the fittings listed below
Tools required
3
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 6
B
Metal dowel (F901) x 14
C
D E F
G
K
Rule Scissors Hammer Eye protection
(when using a
hammer or drill)
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Large locking
nut (F900) x 6
Nail (F51) x 19
Small locking
nut (F3) x 8 9mm Screw (F73) x 16
9mm Screw (F74) x 8
H
Drawer runner (F1004) x 8
Cross-head
screwdriver
IHandle (F847a ) x 4
aIHandle screw (F847b) x 8
b J
Knock-in Peg (F171GY) x 16
L
Wedgefix (F639) x 16
Plastic Nail (F91) x 4

Assembly Instructions
4
Step 1
80%
B
B
B
6
Step 2
Prepare the drawer
fronts
Screw 2 metal dowels
into the holes shown on
the back of each drawer
front .
Note: Tighten metal
dowels up fully against
the panels.
B
6
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Step 3
D
7
8
Attach the drawer
sides to the drawer
front
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
7
8
6
D
7
8
x 4
D
x 4
Small groove
6
Note: The locking nuts can be on
either surface of the drawer sides.
Make sure that the small groove
is on the inside, as shown.
B
B
D
D
Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
DD
78
x 4 x 4
7
8

Assembly Instructions
5
Step 4
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
10
7 8
6
9
7 8
10
9
9
J
7 8
Attach the handles
Attach a handle to
each drawer front
using 2 screws .
6
I a
I b
6
6
x 4
x 4
11
J
J
Step 7
Fit the wedgefixes
Turn the drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
L
J
J
L
L
L
9
7
8
10
8
10
7
6
I
7
I b
I b
I a
6
x 4
6
L
L
x 4

A
Assembly Instructions
6
Step 8
Unfinished
back edge
F
H
a:
b:
Finished
front edge
F
H
Finished
front edge
Finished
front edge
F
H
F
H
F
H
F
H
F
F
F
F
Prepare the left side
a: Place 4 runners on
left side . Slide back
top of runner and use
2nd hole from the front
to fit 1st screw .
b: Slide runner back the
other way and use 2nd
hole from the back to fit
2nd screw .
c: Insert 1 large locking
nut into the left side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Tap a wooden dowel
into the left side .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Screw 2 metal dowels
into the left side .
1
H
F
F
1
1
c:
C
B
B
1
C
1
A
B
1
1
10mm
A
C

A
Assembly Instructions
Step 9
7
Prepare the right side
a: Place 4 runners on
right side . Slide back
top of runner and use
2nd hole from the front
to fit 1st screw .
b: Slide runner back the
other way and use 2nd
hole from the back to fit
2nd screw .
c: Insert 1 large locking
nut into the right
side .
Tap a wooden dowel
into the right side .
Screw 2 metal dowels
into the right side .
2
H
F
b:
c:
a:
Finished
front edge
F
H
Unfinished
back edge
F
H
F
H
F
H
F
H
F
H
2
Finished front edge
F
F
F
F
Finished front edge
2
F
2
C
B
B
C
2
2
2
A
B

A
Assembly Instructions
8
Step 10
A
C
C
Prepare the 2 rails
Insert 2 large locking
nuts into the holes in
the 2 rails .
Tap 1 wooden dowel
into each end of the 2
rails .
4
C
A
4
plain chipboard surface
4
Step 11
Fit the 2 rails
Push the 2 rails onto
right side as shown.
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the 2 rails.
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
C
C
4
2
25
Support this rail
until the left side
has been fitted in
the next step.
The back edge of the top
rail must be flush with the
back edge of the right side.
Finished
surface
plain chipboard surface
plain chipboard surface
4
4
x 2
plain chipboard surface
4
plain chipboard surface
4
2
B
C

Assembly Instructions
Step 12
9
Step 13
1
4
C
4
C
Fit the left side
Fit the left side to the
2 rails .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the 2 rails .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
Stand the unit up.
B
B
Prepare the top
Screw 2 metal dowels
into the top .
Note: Tighten metal
dowels up fully against
the panel.
B
3
3
4
4
1