Argox AS-8060 User manual

AS-8060
Barcode Scanner
User Manual
http://www.argox.com
[email protected]
Version: 1.0
Date: Sept. 18, 2019
V1.0-23-08-20
17

AS-8060
User Guide
ii
Regulatory Compliance
FEDERAL COMMUNICATIONS
COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/ TV
technician for help.
CAUTION:
Any changes or modifications not expressly
approved by the grantee of this device could void the
user's authority to operate the equipment.

AS-8060
User Guide
iii
Note: All brands and trademarks are the
property of their respective owners.
Note: The specifications contained herein
are subject to change without notice.
警告使用者:
這是甲類的資訊產品，在居住的環境中使用時，可
能會造成射頻干擾，在這種情況下，使用者會被要
求採取某些適當的對策。

AS-8060
User Guide
1
Introduction
Your AS-8060 is a 1D CCD scanner that has
been configured at the factory with default
settings.
Since many host systems have unique
formats and protocol requirements, Argox
provides a wide range of configurable
features that may be selected using this bar
code based configuration tool. Once the
configuration is completed, the scanner
stores the settings in nonvolatile memory.
The embedded memory saves the settings
when the power is turned off.
Turn off the computer’s power before
connecting the scanner, and then power up
the computer once the scanner is fully
connected.
You can change a parameter value in the
way described below:
Scan the appropriate bar codes in this
guide. These new values replace the
standard default values in memory.
NOTE: Most computer monitors allow scanning the
bar codes directly on the screen. When
scanning from the screen, be sure to set the
document magnification to a level where
you can see the bar code clearly, and bars
and/or spaces are not merging.

AS-8060
User Guide
2
Application Field:
Jewelry Tag
Manufacturing
Transportation & Logistics
Healthcare
Feature:
Rich to make daily work simple and easy
2500 pixels CCD image sensor
Scan Speed >= 270 times/sec
Max. reading resolution: 3mil (0.762mm)
Depth of Field: 15~330mm
(EAN, 13mil/0.33mm, PCS 90%)
Drop resistance: 1.5 meters onto the
concrete
Auto-sensing (presentation) mode
available

AS-8060
User Guide
3
Version information setting code
000A0
Version
(custom)
000A1
Display internal
string
(custom)
000A2
Display serial
number
(custom)
000B0
Factory default
09990
Enable the code
setting function
09991
Disable the code
setting function
Interface mode setting code
000601
RS-232
000602
USB-HID
(Default)
000603
USB Virtual Com
Note: If you use the scanner that communicates with your computer
via a serial interface (e.g. COM1...COM8), but your computer
does not have any serial port, you will require a so-called virtual
COM port driver. This virtual COM port driver allows you to
assign a virtual COM port connection number to your computer
connected via a USB port and enables bidirectional
communication between your computer and this scanner.
To download the USB virtual COM port driver, go to the Argox
global website (http://www.argox.com/) to download the virtual
COM port driver of AS-8060 scanner.
After downloading the driver, start to install it. When you finish
installing the driver, it is suggested to restart your computer. The
system will automatically detect the scanner.
Scan mode setting code
013300
Trigger mode
(Default)
013304
Continuous scan
mode
013302
Key delay

AS-8060
User Guide
4
013301
Single not
triggered
013303
Key delay not
triggered
013305
Auto flashing
Sound setting code
014201
Sound on
(Default)
014200
Sound off
0145800
Buzzer frequency
2048
014300
High volume
sound
014301
Low volume
sound
0145AAA
Buzzer frequency
2731
Character hiding and replacement setting code
01400
Code ID off
(Default)
01401
Code ID on
01402
Rear code ID on
0201x
Display code
front character
(Default)
0200[SPACE]
Hide code front
blank
0203
Display code rear
character
(Default)
0202[SP]
Hide code rear
character n
(“n” indicates a
blank key.)
0205-
Display characters
inside code
(Default)
0204-
Hide –inside
code

AS-8060
User Guide
5
020600
Disable A replace
0 in code
(Default)
02060A
Enable A replace 0
in code
023300
Display rear
characters
(Default)
023305
Hide rear 5
characters
023301
Hide rear 1
characters
023400
Display front
characters
(Default)
023405
Hide front 5
characters
023900
Display middle
characters
(Default)
023905
Hide 5 middle
characters
024004
Forward start from
4th character
0160049
FUNC1 replace
with 1
0161050
FUNC2 replace
with 2
0162051
FUNC3 replace
with 3
0163054
FUNC4 replace
with 4
0182013
Disable enter
replace
(Default)
0182055
Enter replace with
5

AS-8060
User Guide
6
Serial port setting code
000701
Baud rate 600bps
000702
Baud rate 1200bps
000703
Baud rate
2400bps
000704
Baud rate
4800bps
000705
Baud rate 9600bps
(Default)
000706
Baud rate
19200bps
000707
Baud rate
38400bps
000708
Baud rate 57600bps
000709
Baud rate
115200bps
001200
Serial Port:
No Check
001201
Serial port:
XON/OFF
001202
Serial port:
RTS/CTS
0013020
Serial port
handshake
timeout 2s
0013050
Serial port
handshake
timeout 5s
00080
Serial port
8-bit data
00081
Serial port
7-bit data
00090
Serial port
1 stop bit

AS-8060
User Guide
7
00091
Serial port
2 stop bits
001000
Serial port
No parity check
001001
Serial port
odd parity check
001002
Serial port
even parity check
Normal function setting code
02501
Enable upload
setting barcodes
02500
Disable upload
setting barcodes
(Default)
01640
FUNC cast light
upon cancel
(Default)
02510
Disable change
02511
All uppercase
02512
All lowercase
02513
Uppercase
interchange with
lowercase
01411
Enable
command beep
01410
Disable command
beep
00161
Forward image
identify
(Default)
00160
Reverse image
identify
001500
Fastest transmit
rate